NAD M50.2 Owner's Manual

Also see for M50.2: Service manual User manual

Contents

NAD M50.2 Owner's Manual Manual pdf 3 page image

Battery must not be exposed to excessive heat such as sunshine, fire or thelike.WARNINGTO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TORAIN OR MOISTURE.CAUTIONTO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLYINSERT.FCC WARNING (USA NOTICE)This equipment may generate or use radio frequency energy. Changes ormodifications to this equipment may cause harmful interference unless themodifications are expressedly approved in the manual. The user could lose theauthority to operate this equipment if an unathorized change or modification is made.LABELING INFORMATIONThis device complies with Part 15 of the FCC rules. Operation is subject to the followingtwo conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that maycause undesired operation.RF EXPOSURE STATEMENTThe antenna(s) used for this transmitter must be installed to provide a separationdistance of at least 20 cm from all persons and must not be located or operated inconjunction with any antenna or transmitter other than those contained in this device.RESPONSIBLE PARTYLENBROOK AMERICA6 Merchant StreetSharon, MA 02067USATelephone: 800 263 4641; 781 784-8586Facsimile: 781 784-8386This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that maycause undesired operation.WARNINGChanges or modifications to this unit not expressly approved by the party responsiblefor compliance could void the user's authority to operate the equipment.NOTEThis equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.• Consult the dealer or an experienced radio/ TV technician for help.CANADA NOTICE“This Class B digital apparatus complies with Canadian ICES-003.”This device complies with Industry Canada license-exempt RSS-210. Operation issubject to the following two conditions: (1) this device may not cause Interference,and (2) this device must accept any interference, including interference that maycause undesired operation of the device.• no naked flame sources such as lighted candles should be placed on theapparatus;• the use of apparatus in tropical climateTHE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN ANEQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THEPRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THEPRODUCT’S ENCLOSURE THAT MAYBE OF SUFFICIENT MAGNITUDE TOCONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDEDTO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATINGAND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATUREACCOMPANYING THE APPLIANCE.CAUTIONThis equipment employs a Laser System. To ensure proper use of this product, pleaseread the complete owner’s manual, available online at www.nadelectronics.com/support, and retain for future reference. Should the unit require maintenance, contactan authorized service location. Use of controls, adjustments or the performance ofprocedures other than those specified may result in exposure to laser radiation. Toprevent direct exposure to laser beam, do not try to open the enclosure. Visible laserradiation when the enclosure is opened.DO NOT STARE INTO BEAMCAUTION REGARDING PLACEMENTTo maintain proper ventilation, be sure to leave a space around the unit (from thelargest outer dimensions including projections) that is equal to or greater than shownbelow.Left and Right Panels: 10 cmRear Panel: 10 cmTop Panel: 10 cmWARNINGIf this product is used at 240VAC, a suitable attachment plug should be used.IMPORTANT SAFETY INSTRUCTIONSCLASS 1 LASER PRODUCTKLASSE 1 LASER PRODUKTLUOKAN 1 LASER LAITEKLASS 1 LASER APPARATCLASSE 1 PRODUIT LASER3ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ