Mitsubishi Electric MI1002-W Startup Manual

Also see for MELIPC MI1002-W: User manual Startup guide

MITSUBISHI ELECTRICINDUSTRIAL PCMI1002-W，MI1002-W-CLSTART-UP GUIDEBCN-P5999-0990-E(2102)NEC Ver.5 Feb. 2021Before using this product, please read this manual and the relevant manuals carefully and pay fullattention to safety to handle the product correctly.Follow the instructions in this document for the safe use of this product. User's Manual describes hazardousparts of the product, possible hazards, and how to avoid them. Components of the product with possibledanger are indicated with a warning label placed on or around them (or, in some cases, by printing thewarnings on the computer).In User's Manual or on warning labels, " " or " " is used to indicate a degree of danger.These terms are defined as follows:Indicates the potential for death or serious injury.Indicates there is a risk of burns, other personal injury,or property damage.Under some circumstances, failure to observe the precautions given under " " may lead toserious consequences.Observe the precautions of both levels because they are important for personal and system safety.Make sure that the end users read this manual and then keep the manual in a safe place for future reference.Precautions and notices against hazards are presented with one of the following three symbols.AttentionThis symbol indicates the presence of a hazard if theinstruction is ignored. An image in the symbol illustratesthe hazard type. Electric shock riskProhibitedactionThis symbol indicates prohibited actions. An image in thesymbol illustrates a particular prohibited action.Do not disassembleMandatoryactionThis symbol indicates mandatory actions. An image in thesymbol illustrates a mandatory action to avoid a particularhazard. Disconnect a plugAttentionIndicates the potential forsmoke and/or fire to occur. Indicates the risk of electric shock.Indicates the potential for damagecaused by high temperatures.Indicates there is a risk ofexplosion that can result in injuries.Indicates an attention that cannotbe specifically identified.Make sure to follow the instruction.Prohibited actionsDo not disassemble, repair, ormodify this product. Otherwise,an electric shock or fire may becaused.Do not use this product in placesnear water or liquids. Otherwise anelectric shock or fire may becaused.Do not install this product near afire. Otherwise a fire may becaused.Do not touch with wet hand.Otherwise, an electric shockmay be caused.Do not touch this product.Otherwise, an electric shockmay be caused.Indicates a general prohibitedaction that cannot be specificallyidentified.Mandatory actionsUnplug the power cord of thisproduct. Otherwise, an electricshock or fire may be caused.Indicates a mandatory action thatcannot be specifically identified.Make sure to follow theinstruction.Make sure equipment is properlygrounded.Notations in this manualIndicates items that must be observed in handling the hardware.General NotesDo not use the product if any smoke, odor, or noise is present.If smoke, an abnormal odor or a sound is generated from the product, immediatelyturn off the main unit, unplug the power cable from the outlet, and then contact yournearest sales agent or maintenance service company. An electric shock or firemight result if you continue to use the product.Do not insert needles or metal objects.Do not remove rubber caps or other covers on this product to insert needles, metalobjects, or other foreign objects into openings. Doing so may cause an electricshock, burns, or fire.Keep water or foreign objects away from the product.Do not drop liquids such as water or other foreign objects such as a pin or a paperclip into this product. Failure to follow this warning may cause an electric shock, afire. If such things accidentally enter the product, immediately turn off the power anddisconnect the power plug from the outlet. Do not disassemble the product, andcontact your sales representative or a maintenance service company.Notes on Power ConnectionsPlug the power cord into an outlet that matches the voltage of the unit.Plug the power cord supplied with this product into a 100V outlet in line with thevoltage inscribed on the unit. When using this product in a country or region otherthan Japan, prepare a power cord corresponding to the power supply for the countryor region where this product will be used. Failure to use an appropriate power cablemay cause a fire.Do not hold the power plug with a wet hand.Do not insert/remove the power cable plug with wet hands.Failure to follow this warning may cause an electric shock.Secure safety grounding.Connect the 3-pin power plug of the attached AC power cable to a 3-pin outlet. Usethe attached conversion plug for the double-pole outlet to connect the earth cableto the earth terminal for the double-pole outlet. Secure grounding for safety (toprevent electric shock) by using the FG cable. Ground the main unit beforeconnecting the power plug.Disconnect the power plug from the power source before disconnecting grounding.Plug the power cord into the specified outlet.Use a 3-pin outlet with ground electrode or 2-pin outlet with ground terminal thatmatches the specified voltage. If you are using a 2-pin outlet with ground terminal,use a 2-pin conversion plug with a ground wire supplied with this product andconnect the ground wire securely to the ground terminal of the outlet. Use of anoutlet other than that specified may result in fire or electrical leakage.Do not use extension cords.Do not install the server in any environment that requires an extension cord.Connecting to a cord that does not conform to the power supply specs of thisproduct causes overheating, resulting in fire.Do not connect power cable to overloaded extension cords.The electric current exceeding the rated flow overheats the outlet, which may causea fire.Hold the plug part when removing the AC power cable.Pull the plug by holding the plug part to disconnect the AC power cable. Pulling theAC power cable by holding the cord will cause breakage and might cause fires tooccur.Secure the AC power cable in place.Be sure to secure the AC power cable in place. Incomplete installation causes aloose connection, resulting in smoke or fire.Use the authorized AC power cable.Use only the AC power cable supplied with the product. Electric current exceedingthe rated flow could cause fire. Also, observe the following precautions to preventelectrical shock or fire caused by a damaged power cable.◇ Do not stretch the power cable.◇ Do not bend the power cable.◇ Do not step on the power cable.◇ Do not pinch the power cable.◇ Do not secure the power cable with staples or equivalents.◇ Uncoil the power cable before use.◇ Keep chemicals away from the power cable.◇ Do not place any object on the power cable.◇ Do not alter, modify, or repair the power cable.◇ Do not use a damaged power cable. Replace the damaged power cable with apower cable of the same standard. Contact your sales representative or amaintenance service company for replacement.Do not use the attached power cable for any other devices or usage.The power cable that comes with the product is designed for this product. Do not usethe attached power cord for any other products or purposes. Doing so may cause afire or an electric shock.Notes on Installation EnvironmentDo not connect the ground wire to a gas pipe.Never connect the ground wire to a gas pipe. Failure to follow this warning maycause a gas explosion or a fire.Install or store this product in the specified place.Do not install this product in the following places or any place other than specifiedin this manual. Failure to follow this instruction may cause a fire.● A dusty or humid place● A place exposed to direct sunlight or rainwater● A place where flammable gas or corrosive gas is present● An unstable placeDo not use this product in an environment where corrosive gas is present.Do not install this product in a place subject to corrosive gases including sulfurdioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, or ozone. Do notinstall this product in an environment containing corrosion promoting componentssuch as sodium chloride and sulfur and conductive metal etc. in dust and air. Failureto follow this warning may corrode the printed board in this product, leading tomalfunction, smoke emission or fire. If you have any questions, please contact yoursales or maintenance representative.Remove AC power cable when connecting interface cables.Remove the AC power cable from the outlet or other supply power source whenconnecting or removing interface cables.Connecting or removing interface cables while the AC power cable is connected tothe outlet or other supply power source might result in electric shock.Use only the specified interface cable.Use only interface cables provided by MITSUBISHI ELECTRIC CORPORATIONand locate a proper device and connector before connecting a cable. Using anunauthorized cable or connecting a cable to an improper destination may cause ashort circuit, resulting in a fire. Also, observe the following notes on using andconnecting an interface cable.● Do not use any damaged cable connector. ● Do not step on the cable.● Do not place any object on the cable. ● Do not use any damaged cable.● Do not use the server with loose cable connections.For more information about interface cables, please contact your sales ormaintenance representative.Secure cables in place.Be sure to secure the power cable and interface cables in place. Incomplete installationcauses a loose connection, resulting in smoke or fire.Hold the plug part when removing the AC power cable and interface cables.Pull the plug by holding the plug part to disconnect the AC power cable and interfacecables. Pulling these cables by holding the cord will cause breakage and mightcause fires to occur.Notes for MaintenanceDo not remove the lithium metal battery (button type).A lithium metal battery (button type) is installed in this product. Do not attempt toremove this lithium metal battery (button type). Exposing the battery to flame orwater may cause it to catch fire or rupture.If the product does not work normally due to the dead battery, please contact yoursales or maintenance representative. Never disassemble or replace the battery byyourself.Remove AC power cable when connecting interface cables.Remove the AC power cable from the outlet or other supply power source whenconnecting or removing interface cables.Connecting or removing interface cables while the AC power cable is connected tothe outlet or other supply power source might result in electric shock.Do not touch high temperature parts.Do not touch the chassis and AC power adaptor immediately after using the device.They are hot and might cause burns when touched.Wait at least 30 minutes after turning the power to the main device OFF beforeinstalling/removing devices installed in the main unit.Secure cables in place.Be sure to secure the power cable and interface cables in place. Incompleteinstallation causes a loose connection, resulting in smoke or fire.Do not use while dust is accumulated on the AC power cable.Do not use this main unit while dust is accumulated on the power cable plug. Longperiods of use without cleaning the dust that has accumulated on the power cableplug might result in electric discharge between the plug and pins and causes firesto occur.Notes on maintenancePlease read the manual for each component before maintenance.Do not disassemble.Please do not disassemble the power supply, battery, optical drives, and disk drivesin a manner other than that for which described in this document.Not only does the product not work properly but also there is a risk of electric shockor fire.Notes for OperationDo not touch during thunderstorms.Do not remove the main unit cover when the power plug is connected tothe AC outlet. Failure to follow this warning may cause an electric shock.Keep creatures away from this product.Keep small animals, insects, and other creatures away from this product. Hair orother waste matter from the creature may enter this product and cause a fire orelectric shock.Do not place any objects on this product.Doing so may cause the product to malfunction, or the object placed on the productmay fall and cause personal injury or damage to nearby personal belongings.Do not touch high temperature parts.Do not touch the chassis and AC power adaptor immediately after using the device.They are hot and might cause burns when touched.Wait at least 30 minutes after turning the power to the main device OFF beforeinstalling/removing devices installed in the main unit.A warning label is placed on the components and peripherals that require careful handling (The warning labelis printed or attached). The warning labels contain information about possible dangers in dealing with thisproduct. Therefore, do not peel off, cover, or dirty the warning labels. If no warning label is printed or attachedon this product, or if the attached or printed warning label is peeling off or dirty, please contact your salesrepresentative.● Precautions for transferring this product to a third partyWhen transferring (or selling) this product to a third party, please pass on this document, the attached partsand instructions, license agreement and other documents together with the product.● Disposal precautionsWhen disposing of this product, treat it as industrial waste.This product contains lithium battery. When disposing of batteries, separate them from other wastesaccording to the local regulations. For details on battery regulations in EU member states, refer to theUser’s Manual.Be sure to dispose of the attached AC adaptor and power cord together with this product to preventdiversion for other purposes.When transporting lithium batteries, follow the transportation regulations. For details on the regulations, referto Mitsubishi Technical Bulletins as follows.Precautions for transport regulations on lithium batteries (FA-A-0259)This equipment has been tested and complies with the limits for a Class A digital device, pursuant to Part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferencewhen the equipment is operated in a commercial environment. This equipment generates, uses, and canradiate radio frequency energy and, if not installed and used in accordance with the instruction manual, maycause harmful interference to radio communications. Operation of this equipment in a residential area is likelyto cause harmful interference, in which case the user will be required to correct the interference at his ownexpense.This Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.This is a Class A product. In a domestic environment, this product may cause radio interference, in which casethe user may be required to take adequate measures.This product complies with harmonic current standard EN 61000-3-2.This product has been designed and produced to meet the harmonic environmental target level of thecommercial power system according to “Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits forharmonic current emissions (equipment input current ≦ 20 A per phase)” of EN.(1). This product ("the PRODUCT") shall be used in conditions;i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major orserious accident; andii) where the backup and fail-safe function are systematically or automatically provided outside of thePRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.(2). The PRODUCT has been designed and manufactured for the purpose of being used in generalindustries. MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOTLIMITED TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY,TORT, PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGETO PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOTINTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED INMITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS ANDGUIDELINES FOR the PRODUCT.("Prohibited Application")Prohibited Applications include, but not limited to, the use of the PRODUCT in; Nuclear Power Plants and any other power plants operated by Power companies, and/or any othercases in which the public could be affected if any problem or fault occurs in the PRODUCT. Railway companies or Public service purposes, and/or any other cases in which establishment of aspecial quality assurance system is required by the Purchaser or End User. Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevatorand Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment forRecreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials orChemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury tothe public or property.Equipment base label Serial No. referenceexample ) TSBH12345678BH: Last two digits of manufacturing age (A:0, … , J:9)1: manufacturing month (1:January, … , 9:September, A:October, B:November, C:December)WarningCaution!WarningCaution!WarningCaution!WarningCaution!Caution!WarningCaution!Caution!SAFETY PRECAUTIONSSymbols used in this manual and on warning labelsSafety NotesSAFETY PRECAUTIONS - CONT’D -Warning LabelsPrecaution for transfer or disposal of this productBe sure to erase important data in the storage completely before transferring or disposing ofthis product. Even if the data is invisible on the OS, it may remain in storage. To prevent dataleakage to third parties, the customer is responsible for erasing the data.Cautions for transportation by air or seaFCC statementIndustry Canada statementEuropean Community statementHarmonic Current Standard ComplianceUsing this productConfirmation method in the manufacture dateThis product is developed and manufactured with NEC Corporation.Produced by NEC CorporationMI1002-W AC AdapterExampleExampleExampleCAUTION: For use with Information Technology EquipmentINDOOR USE ONLYWarning" WarningWarningWarningWarning Caution!"Caution!*CBZ-020996-001-03*

/ 2

Related manuals for Mitsubishi Electric MELIPC MI1002-W