Mitsubishi Electric GT1675M-STBA General Description Manual

GT16 General DescriptionThank you for purchasing the GOT1000 Series.GT1695M-XTBAGT1675M-STBAGT1675-VNBAGT1665M-STBAGT1662-VNBAGT1695M-XTBDGT1675M-STBDGT1675-VNBDGT1665M-STBDGT1662-VNBDGT1685M-STBAGT1675M-VTBAGT1672-VNBAGT1665M-VTBAGT1655-VTBDGT1685M-STBDGT1675M-VTBDGT1672-VNBDGT1665M-VTBDPrior to use, please read both this manual and thedetailed manual thoroughly to fully understand theproduct.MODEL GT16-U-GD-EModelcode 1D7MP6IB(NA)-0800544ENG-A(1410)MEE12345678901234567890SAFETY PRECAUTIONS(Always read these precautions before using this equipment.)Before using this product, please read this manual and the relevantmanuals introduced in this manual carefully and pay full attention tosafety to handle the product correctly.The precautions given in this manual are concerned with this prod-uct.In this manual, the safety precautions are ranked as "WARNING"and "CAUTION".Note that the CAUTION level may lead to a serious accidentaccording to the circumstances.Always follow the instructions of both levels because they are impor-tant to personal safety.Please save this manual to make it accessible when required andalways forward it to the end user.[DESIGN PRECAUTIONS]Indicates that incorrect handling may causehazardous conditions, resulting in death orsevere injury.Indicates that incorrect handling may causehazardous conditions, resulting in medium orslight personal injury or physical damage. Some failures of the GOT, communication unit or cable may keep the outputson or off.Some failures of a touch panel may cause malfunction of the input objectssuch as a touch switch.An external monitoring circuit should be provided to check for output signalswhich may lead to a serious accident.Not doing so can cause an accident due to false output or malfunction. If a communication fault (including cable disconnection) occurs duringmonitoring on the GOT, communication between the GOT and PLC CPU issuspended and the GOT becomes inoperative.For bus connection : The CPU becomes faulty and the GOT becomesinoperative.For other than bus connection : The GOT becomes inoperative.A system where the GOT is used should be configured to perform anysignificant operation to the system by using the switches of a device otherthan the GOT on the assumption that a GOT communication fault will occur.Not doing so can cause an accident due to false output or malfunction. Do not use the GOT as the warning device that may cause a seriousaccident.An independent and redundant hardware or mechanical interlock is requiredto configure the device that displays and outputs serious warning.Failure to observe this instruction may result in an accident due to incorrectoutput or malfunction.WARNINGCAUTIONWARNING[DESIGN PRECAUTIONS][DESIGN PRECAUTIONS][MOUNTING PRECAUTIONS] Incorrect operation of the touch switch(s) may lead to a serious accident if theGOT backlight is gone out.When the GOT backlight goes out, although the POWER LED blinks (green/orange) and the display section dims, the input of the touch switch(s) remainsactive.This may confuse an operator in thinking that the GOT is in "screensaver"mode, who then tries to release the GOT from this mode by touching thedisplay section, which may cause a touch switch to operate.Note that the following occurs on the GOT when the backlight goes out.• GT1655-V: The POWER LED blinks (green/orange) and the monitor screenappears blank.• Models other than GT1655-V: The POWER LED blinks (green/orange) andthe monitor screen appears dimmed. The display section of the GT16 is an analog-resistive type touch panel.If you touch the display section simultaneously in 2 points or more, the switchthat is located around the center of the touched point, if any, may operate.Do not touch the display section in 2 points or more simultaneously.Doing so may cause an accident due to incorrect output or malfunction. When programs or parameters of the controller (such as a PLC) that ismonitored by the GOT are changed, be sure to reset the GOT or shut off thepower of the GOT at the same time.Not doing so can cause an accident due to false output or malfunction. Do not bundle the control and communication cables with main-circuit, poweror other wiring.Run the above cables separately from such wiring and keep them a minimumof 100mm apart.Not doing so noise can cause a malfunction. Do not press the GOT display section with a pointed material as a pen ordriver.Doing so can result in a damage or failure of the display section. When the GOT is connected to the Ethernet network, the available IPaddress is restricted according to the system configuration.• When multiple GOTs are connected to the Ethernet network:Do not set the IP address (192.168.0.18) for the GOTs and the controllers inthe network.• When a single GOT is connected to the Ethernet network:Do not set the IP address (192.168.0.18) for the controllers except the GOTin the network.Doing so can cause the IP address duplication. The duplication cannegatively affect the communication of the device with the IP address(192.168.0.18).The operation at the IP address duplication depends on the devices and thesystem. Turn on the controllers and the network devices to be ready forcommunication before they communicate with the GOT.Failure to do so can cause a communication error on the GOT. Be sure to shut off all phases of the external power supply used by thesystem before mounting or removing the GOT main unit to/from the panel.Not doing so can cause the unit to fail or malfunction. Be sure to shut off all phases of the external power supply used by thesystem before mounting or removing the communication unit, option functionboard onto/from the GOT.Not doing so can cause the unit to fail or malfunction. When installing the option function board, wear an earth band etc. to avoidthe static electricity.Not doing so can cause a unit corruption. Use the GOT in the environment that satisfies the general specificationsdescribed in this manual.Not doing so can cause an electric shock, fire, malfunction or productdamage or deterioration. When mounting the GOT to the control panel, tighten the mounting screws inthe specified torque range (0.36 to 0.48 N•m) with a Phillips-head screwdriverNo.2.Undertightening can cause the GOT to drop, short circuit or malfunction.Overtightening can cause a drop, short circuit or malfunction due to thedamage of the screws or the GOT. When loading the communication unit to the GOT, fit it to the connectioninterface of the GOT and tighten the mounting screws in the specified torquerange (0.36 to 0.48 N•m) with a Phillips-head screwdriver No.2.Under tightening can cause the GOT to drop, short circuit or malfunction.Overtightening can cause a drop, failure or malfunction due to the damage ofthe screws or unit. When mounting the option function board onto the GOT, connect it to thecorresponding connector securely and tighten the mounting screws within thespecified torque range (0.25 to 0.35 N•m) with a Phillips-head screwdriverNo.1.Undertightening can cause malfunction due to poor contact.Overtightening can cause malfunction due to screw or unit damage. When inserting a CF card into the GOT, push it into the insertion slot until theCF card eject button will pop out.If not properly inserted, a bad connection may cause a malfunction. When inserting/removing a CF card into/from the GOT, turn the CF cardaccess switch off in advance.Failure to do so may corrupt data within the CF card. When removing a CF card from the GOT, make sure to support the CF cardby hand, as it may pop out.Failure to do so may cause the CF card to drop from the GOT and break.WARNINGCAUTIONWARNINGCAUTION[MOUNTING PRECAUTIONS][WIRING PRECAUTIONS][TEST OPERATION PRECAUTIONS][STARTUP/MAINTENANCE PRECAUTIONS] When installing a USB memory to the GOT, make sure to install the USBmemory to the USB interface firmly.Failure to do so may cause a malfunction due to poor contact. Before removing the USB memory from the GOT, operate the utility screenfor removal. After the successful completion dialog box is displayed, removethe memory by hand carefully.Failure to do so may cause the USB memory to drop, resulting in a damageor failure of the memory. For closing the USB environmental protection cover, fix the cover by pushingthe mark on the latch firmly to comply with the protective structure. Remove the protective film of the GOT.When the user continues using the GOT with the protective film, the film maynot be removed. Operate and store the GOT in environments without direct sunlight, hightemperature, dust, humidity, and vibrations. When using the GOT in the environment of oil or chemicals, use theprotective cover for oil.Failure to do so may cause failure or malfunction due to the oil or chemicalentering into the GOT. Be sure to shut off all phases of the external power supply used by thesystem before wiring.Failure to do so may result in an electric shock, product damage ormalfunctions. Always ground the FG terminal, LG terminal, and Functional ground terminalof the GOT power to the protective ground conductors dedicated to the GOT.Not doing so may cause an electric shock or malfunction. When tightening the terminal screws, use a Phillips-head screwdriver No.2. Terminal screws which are not to be used must be tightened always at torque0.5 to 0.8 N•m.Otherwise there will be a danger of short circuit against the solderlessterminals. Use applicable solderless terminals and tighten them with the specifiedtorque.If any solderless spade terminal is used, it may be disconnected when theterminal screw comes loose, resulting in failure. Correctly wire the GOT power supply section after confirming the ratedvoltage and terminal arrangement of the product.Not doing so can cause a fire or failure. Tighten the terminal screws of the GOT power supply section in the specifiedtorque range (0.5 to 0.8 N•m). Undertightening can cause a short circuit ormalfunction.Overtightening can cause a short circuit or malfunction due to the damage ofthe screws or the GOT. Exercise care to avoid foreign matter such as chips and wire offcuts enteringthe GOT. Not doing so can cause a fire, failure or malfunction. The module has an ingress prevention label on its top to prevent foreignmatter, such as wire offcuts, from entering the module during wiring.Do not peel this label during wiring.Before starting system operation, be sure to peel this label because of heatdissipation. Plug the communication cable into the connector of the connected unit andtighten the mounting and terminal screws in the specified torque range.Undertightening can cause a short circuit or malfunction.Overtightening can cause a short circuit or malfunction due to the damage ofthe screws or unit. Plug the QnA/ACPU/Motion controller(A series) bus connection cable byinserting it into the connector of the connected unit until it "clicks".After plugging, check that it has been inserted snugly.Not doing so can cause a malfunction due to a contact fault. Before performing the test operations of the user creation monitor screen(such as turning ON or OFF bit device, changing the word device currentvalue, changing the settings or current values of the timer or counter, andchanging the buffer memory current value), read through the manualcarefully and make yourself familiar with the operation method.During test operation, never change the data of the devices which are used toperform significant operation for the system.False output or malfunction can cause an accident. When power is on, do not touch the terminals.Doing so can cause an electric shock or malfunction. Correctly connect the battery connector.Do not perform the following actions to the battery.• Charging, disassembling, heating, short-circuiting, or soldering the battery,or throwing it into the fireDoing so will cause the battery to produce heat, explode, or ignite, resulting ininjury and fire. Before starting cleaning or terminal screw retightening, always switch off thepower externally in all phases.Not switching the power off in all phases can cause a unit failure ormalfunction.Undertightening can cause a short circuit or malfunction.Overtightening can cause a short circuit or malfunction due to the damage ofthe screws or unit.CAUTIONWARNINGCAUTIONWARNINGWARNING[STARTUP/MAINTENANCE PRECAUTIONS][TOUCH PANEL PRECAUTIONS][BACKLIGHT CHANGING PRECAUTIONS][DISPOSAL PRECAUTIONS][TRANSPORTATION PRECAUTIONS] Do not disassemble or modify the unit.Doing so can cause a failure, malfunction, injury or fire. Do not touch the conductive and electronic parts of the unit directly.Doing so can cause a unit malfunction or failure. The cables connected to the unit must be run in ducts or clamped.Not doing so can cause the unit or cable to be damaged due to the dangling,motion or accidental pulling of the cables or can cause a malfunction due to acable connection fault. When unplugging the cable connected to the unit, do not hold and pull thecable portion.Doing so can cause the unit or cable to be damaged or can cause amalfunction due to a cable connection fault. Do not drop the module or subject it to strong shock. A module damage mayresult. Do not drop or give an impact to the battery mounted to the unit.Doing so may damage the battery, causing the battery fluid to leak inside thebattery.If the battery is dropped or given an impact, dispose of it without using. Before touching the unit, always touch grounded metals, etc. to dischargestatic electricity from human body, etc.Not doing so can cause the unit to fail or malfunction. Replace battery with GT15-BAT or GT11-50BAT by Mitsubishi electricCo.only.Use of another battery may present a risk of fire or explosion. Dispose of used battery promptly.Keep away from children.Do not disassemble and do not dispose of in fire. For the analog-resistive film type touch panels, normally the adjustment is notrequired.However, the difference between a touched position and the object positionmay occur as the period of use elapses. When any difference between atouched position and the object position occurs,execute the touch panelcalibration. When any difference between a touched position and the object positionoccurs, other object may be activated. This may cause an unexpectedoperation due to incorrect output or malfunction. Before changing the backlight, always switch off the GOT power externally inall phases (when the GOT is connected to the bus, the PLC CPU power mustalso be switched off externally in all phases) and remove the GOT from thecontrol panel.Not switching the power off in all phases may cause an electric shock.Not removing the unit from the control panel can cause injury due to a drop. When replacing the backlight, use the gloves.Otherwise, it may cause you to be injured. Start changing the backlight more than 5 minutes after switching the GOTpower off.Not doing so can cause a burn due to the heat of the backlight. When disposing of this product, treat it as industrial waste.When disposing of batteries, separate them from other wastes according tothe local regulations.(Refer to the User's Manual for the GOT you are using for details of thebattery directive in the EU member states.) When transporting lithium batteries, make sure to treat them based on thetransport regulations.(Refer to the User's Manual for the GOT you are using for details of theregurated models.) Make sure to transport the GOT main unit and/or relevant unit(s) in themanner they will not be exposed to the impact exceeding the impactresistance described in the general specifications of the User's Manual, asthey are precision devices.Failure to do so may cause the unit to fail.Check if the unit operates correctly after transportation. When fumigants that contain halogen materials such as fluorine, chlorine,bromine, and iodine are used for disinfecting and protecting woodenpackaging from insects, they cause malfunction when entering our products.Please take necessary precautions to ensure that remaining materials fromfumigant do not enter our products, or treat packaging with methods otherthan fumigation (heat method).Additionally, disinfect and protect wood from insects before packing products.CAUTIONCAUTIONWARNINGCAUTIONCAUTIONCAUTIONManualThe following shows manuals relevant to this product.For detailed manuals, refer to the PDF manuals stored in the DVD-ROM for thedrawing software used.For relevant manuals, refer to the Help or the PDF manuals stored in the DVD-ROM for the drawing software used.The latest manuals are also available from MITSUBISHI ELECTRIC FA GlobalWebsite (http://www.MitsubishiElectric.co.jp/fa/).© 2014MITSUBISHI ELECTRIC CORPORATIONBefore using the GOTConnect the connector of the GOT to the connector of the battery.For details on GT16 specifications, installing procedure, EMC Directive, wiring,maintenance and inspection, or checking method for the version and thecompatible standard, refer to GT16 User's Manual (Hardware).Packing ListThe GOT product package includes the following:1. FEATURES(1) Improved monitoring performance and connectivity to FA devices• GT1695M-X, GT1685M-S, GT1675M-S, GT1675M-V, GT1665M-S,GT1665M-V, GT1655-V: The TFT color liquid crystal display (high intensity,wide angle view, and high definition type) provides clear full-color displayand displays small characters clearly.(Displays digital images of BMP and other formats in 65536 colors.)GT1675-VN, GT1672-VN, GT1662-VN: The TFT color liquid crystal displayprovides 4096 or 16 colors to offer a wide range of models that meet userrequirements.• Provides multi-language display function based on Unicode2.1 True Typefont and high-speed drawing of beautiful text.• High speed monitoring through high speed communication at maximum of115.2kbps.• High speed display and high speed touch switch response.• The operation performance is improved by the analog touch panel.• GT1695M-X, GT1685M-S, GT1675M-S, GT1675M-V, GT1665M-S,GT1665M-V: Applicable to a video/RGB unit and a multimedia unit(2) More efficient GOT operations including screen design, startup, adjustment,management and maintenance works• GT1695M-X, GT1685M-S, GT1675M-S, GT1675M-V, GT1665M-S,GT1665M-V, GT1655-V: 15MB user memory is included as standard.GT1675-VN, GT1672-VN, GT1662-VN: 11MB user memory is included asstandard.• Interfaces are included as standard. (Ethernet, RS-232, RS-422/485, CFcard, and USB)• Font installation is available to increase the system fonts.• Combined use of 4 types of alarms (system alarm, user alarm, alarmhistory, alarm popup display) realizes more efficient alarm notification.• Maintenance timing report function is available that measures the backlightenergization time and notifies of maintenance time.Detailed ManualManual name Manual number(Model code)GT16 User's Manual (Hardware)(Sold separately)SH-080928ENG(1D7MD3)GT16 User's Manual (Basic Utility)(Sold separately)SH-080929ENG(1D7MD4)Relevant ManualsModel name Product QuantityGT1695M-XGOT 1Battery (GT15-BAT) 1Installation fitting 8GT16 General Discription 11GT1685M-SGT1675M-SGT1675M-VGT1675-VNGT1672-VNGT1665M-SGT1665M-VGOT 1Battery (GT15-BAT) 1Installation fitting 4GT16 General Discription 11GT1655-VGOT 1Battery (GT11-50BAT) 1Installation fitting 4GT16 General Discription 11• The USB interface is positioned on the GOT front. This enables the systemstartup to be performed more efficiently using FA device startup tool, andeliminates the necessity of indirect works (opening and closing the controlpanel, cable replacement, cable rewiring) in order to improve the workingefficiency.• The blown backlight bulb can be confirmed even during screen saving, withthe blinked POWER LED at backlight shutoff detection.(3) Enhanced support of FA device setup tools• Transferring and monitoring sequence programs with the personal computerconnected to the GOT can be executed when connecting to a PLC CPUwith the direct CPU connection or bus connection. (FA transparent function)2. Part Names and SettingsPart Names and Settings of the GT16*1: No video/RGB interface on the GT1675-VN, GT1672-VN, GT1662-VN, andGT1655-V.*2: Battery holder for the GT1665 and GT1662.*3: No extension interface 2 on the GT1655.*4: Located on the extension interface 2 on the GT1655.*5:Integral with the CF card interface cover for the GT1655.*6:No human sensor on the GT1675, GT1672, GT1665, GT1662, and GT1655.*7:No LG terminal on the GT1655.*8:On the rear face of the GT1655, the functional ground terminal is located on theleft side of the FG terminal.No. Name Description1) POWER LEDLit in green : Power is correctly supplied , Lit in orange :Screen savingBlinks in orange/green : Blown back light bulb , Not lit :Power is not supplied2) Display screen Displays the Utility and the user creation screen.3) Touch key For operating touch switches in the Utility and the usercreation screen4) USB interface (Device) For connecting a personal computer (Connector type: Mini-B)5) USB interface (Host) For USB mouse/keyboard ,data transfer and storage(Connector type: TYPE-A)6) RS-232 interface For communicating with a controller or connecting apersonal computer(Connector type: D sub 9-pin)7) Ethernet interface For communicating with a controller or using the gatewayfunction (Connector type: RJ-45 (modular jack))8) RS-422/485 interface For communicating with a controller (Connector type: 14-pin(female))9) Power terminal *8 Power input terminal, LG terminal*7 , FG terminal10) Extension interface1 For installing an extension unit (I/F-1)11) Extension interface2*3 For installing an extension unit (I/F-2)12) CF card interface For installing a CF card13) CF card access LED Lit : CF card accessed , Not lit : CF card not accessed14) CF card access switchUsed for accepting or stopping the access to the CF cardbefore removing the CF card from the GOTON :CF card being accessed (CF card removalprohibited)OFF :CF card not accessed (CF card removal possible)15) Video/RGB interface *1 For mounting the video input unit, RGB input unit, video/RGB input unit, RGB output unit, or multimedia unit16) Terminating resistorsetting switchFor switching on and off of the terminating resistor for theRS-422/485 communication port17) Optional functionboard interface*4 For installing the optional function board18) Reset switch Hardware reset switch (Inoperative in the bus connection orwith the bus connection unit installed)19) Hole for unitinstallation fitting Hole for inserting the unit installation fitting20) Battely cover*2*5 Houses the battery21) Human sensor*6 Sensor that detects human movement22) Installation switch Used for OS installations at the GOT startupGOTRear face20)12)13)14)21)1)4)5)2),3)19)6) 7) 8) 9)10) 11) 18)17) 16)15)22)Example)GT169519)19)3. Specifications3.1 General Specifications*1: When mounting a multimedia unit (GT16M-MMR), MELSECNET/Hcommunication unit (GT15-J71LP23-25, GT15-J71BR13), or CC-Linkcommunication unit (GT15-J61BT13), the operating ambient temperature mustbe reduced 5 °C against the maximum values described in generalspecifications.Lors du montage d'un module multimédia (GT16M-MMR), du module decommunication MELSECNET/H (GT15-J71LP23-25, GT15-J71BR13) ou dumodule de communication CC-Link (GT15-J61BT13), la température ambiantede fonctionnement doit être réduite de 5°C par rapport aux valeurs maximalesdécrites dans les spécifications générales.*2: Do not use or store the GOT under pressure higher than the atmosphericpressure of altitude 0m (0ft.). Failure to observe this instruction may cause amalfunction.When an air purge is made inside the control panel by adding pressure, theremay be a clearance between the surface sheet and the screen making it difficultto use the touch panel, or the sheet may come off.*3: This indicates the section of the power supply to which the equipment isassumed to be connected between the public electrical power distributionnetwork and the machinery within the premises.Category II applies to equipment for which electrical power is supplied fromfixed facilities.The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.*4: This index indicates the degree to which conductive material is generated in theenvironment where the equipment is used.In pollution degree 2, only non-conductive pollution occurs but temporaryconductivity may be produced due to condensation.3.2 Power Supply SpecificationsThe following indicates the power supply specifications for GT16.3.2.1 For GOTs powered from the 100 to 240VACpower supplyItem SpecificationsOperatingambienttemperature*1Températureambiante defonctionnement *1DisplaysectionZoned'affichage0 to 500 à 50Other thanthe displaysectionAutre que lazoned'affichage0 to 550 à 55Storage ambienttemperature -20 to 60Operating ambienthumidity 10 to 90% RH, non-condensingStorage ambient humidity 10 to 90% RH, non-condensingVibration resistanceCompliantwith JIS B3502 andIEC 61131-2Frequency Acceleration Half-amplitudeSweepcountUnderintermittentvibration5 to 8.4Hz - 3.5mm 10 timeseach in X,Y and Zdirections8.4 to150Hz 9.8m/s 2 -Undercontinuousvibration5 to 8.4Hz - 1.75mm-8.4 to 150Hz 4.9m/s 2 -Shock resistance Compliant with JIS B 3502 and IEC 61131-2 147 m/s 2(15G),3 times each in X, Y and Z directionsOperating atmosphereNo greasy fumes, corrosive gas, flammable gas, excessiveconductive dust, and direct sunlight (Same as storageatmosphere)Operating altitude *2 2000 m (6562 ft) max.Installation location Inside control panelOvervoltage category *3 II or lessPollution degree *4 2 or lessCooling method Self-coolingGrounding Grounding with a resistance of 100Ω or lessPointRefer to GT16 User's Manual for details of the performance specifications of each GOT.NoteOperation at momentary failure• If an instantaneous power failure occurs in the power supply and continues for morethan the permissible period, the GOT will be reset.• Make sure to power on the unit more than 5 seconds after power-off.ItemSpecificationsGT1695M-XTBA GT1685M-STBAGT1675M-STBAGT1675M-VTBAGT1675-VNBAGT1672-VNBAGT1665M-STBAGT1665M-VTBAGT1662-VNBAInput power supply voltage 100 to 240VAC (+10%, -15%)Input frequency 50/60Hz 5%Input max. apparent power 150VA(maximum load)110VA(maximum load)100VA(maximum load)Power consumption 64W or less 46W or less 39W or lessAt backlight off 38W or less 32W or less 30W or lessInrush current 28A or less (4ms) (maximum load)3.2.2 For GOTs powered from the 24VDC powersupply3.3 External DimensionsItemSpecificationsGT1695M-XTBA GT1685M-STBAGT1675M-STBAGT1675M-VTBAGT1675-VNBAGT1672-VNBAGT1665M-STBAGT1665M-VTBAGT1662-VNBAAllowable momentary powerfailure time 20 ms or less (100VAC or more)Noise immunity1,500Vp-p noise voltage, 1 s noise width (whenmeasuring with a noise simulator under 25 to 60Hznoise frequency)Dielectric withstand voltage 1500VAC for 1 minute across power terminals and earthInsulation resistance 10MΩ or more across power terminals and earth by a500V DC insulation resistance testerApplicable wire size 0.75 to 2[mm2]Applicable solderless terminal Solderless terminal for M3 screw RAV1.25-3, V2-S3.3,V2-N3A, FV2-N3AApplicable tightening torque(Terminal block terminal screw) 0.5 to 0.8[N•m]ItemSpecificationsGT1695M-XTBDGT1685M-STBDGT1675M-STBDGT1675M-VTBDGT1675-VNBDGT1672-VNBDGT1665M-STBDGT1665M-VTBDGT1662-VNBDGT1655-VTBDInput power supplyvoltage DC24V (+25%, -20%)Powerconsumption 60W or less 40W or less 38W or less 16W or lessAt backlight off 30W or less 26W or less 27W or less 14W or lessInrush current12A or less(75ms)(maximumload)12A or less (55ms) (maximumload)67A or less(1ms)(maximumload)Allowablemomentary powerfailure time10 ms or lessNoise immunity 500Vp-p noise voltage, 1 s noise width (when measuring with anoise simulator under 25 to 60Hz noise frequency)Dielectric withstandvoltage 500VDC for 1 minute across power terminals and earthInsulationresistance10MΩ or more across power terminals and earth by a 500V DCinsulation resistance testerApplicable wire size 0.75 to 2[mm 2]Applicablesolderless terminalSolderess terminal for M3 screw RAV1.25-3, V2-S3.3, V2-N3A, FV2-N3AApplicabletightening torque(Terminal blockterminal screw)0.5 to 0.8[N•m]Unit:mm (inch)397(15.6)320(12.6)296(11.7)320(12.6)6(0.24)61(2.40)10 382(15.0) 10281(11.1)(0.39) (0.39)GT169510(0.39)10(0.39)Unit: mm (inch)316(12.44)240(10.35)242(9.53)240(9.84)301(11.85)52(2.05)56(2.20)227(8.94) 10(0.39)GT168510(0.39)6(0.24)303 (11.93)252 (9.92)10(0.39)199 (7.83)214 (8.43)10(0.39)56 (2.20)49(1.93)288 (11.34)222 (8.74)Unit: mm (inch)GT1675,GT16726(0.24)190 (7.48)10(0.39)175 (6.89)226 (8.90)52(2.05)175.5 (6.91)175.5 (6.91)241 (9.49)56 (2.20)10(0.39)6(0.24)Unit: mm (inch)GT1665,GT1662135(5.31)10(0.39)10(0.39) 120(4.72)152(5.98)6(0.24)116(4.57)167(6.57)60(2.36)GT1655116(4.57)Unit: mm (inch)

/ 2

Related manuals for Mitsubishi Electric 1D7MP6