Mitsubishi Electric GT10-LDR User Manual

JY997D29501FSafety Precaution (Read these precautions before using.)Before using this product, please read this manual and the relevant manualsintroduced in this manual carefully and pay full attention to safety to handle theproduct correctly.The precautions given in this manual are concerned with this product.In this manual, the safety precautions are ranked as "WARNING" and"CAUTION".Depending on circumstances, procedures indicated by "CAUTION" may also belinked to serious results.In any case, it is important to follow the directions for usage.Indicates that incorrect handling may cause hazardousconditions, resulting in death or severe injury.Indicates that incorrect handling may cause hazardousconditions, resulting in medium or slight personal injuryor physical damage.MOUNTING PRECAUTIONS Use the memory loader in the environment that satisfies the generalspecifications described in GT10 User's manual. Never use the product inareas with excessive dust, oily smoke, conductive dusts, corrosive gas (saltair, Cl2 , H2 S, SO 2 or NO 2), flammable gas, vibration or impacts, or exposedto high temperature, condensation, or rain and wind. Not doing so can causean electric shock, fire, malfunction or product damage or deterioration.STARTUP/MAINTENANCEPRECAUTIONS Do not disassemble or modify the memory loader.Doing so can cause a failure, malfunction, injury or fire. Do not touch the conductive and electronic parts of the memory loaderdirectly. Doing so can cause a memory loader malfunction or failure. When unplugging the cable connected to the GOT, do not hold and pull thecable portion. Doing so can cause the memory loader or cable to bedamaged or can cause a malfunction due to a cable connection fault. Do not bent at a sharp angle or tie the memory loader cables.Doing so can cause the breaking of the cables.DISPOSAL PRECAUTIONS When disposing of the product, handle it as industrial waste.TRANSPORTATIONPRECAUTIONS Make sure to transport the memory loader and/or relevant unit(s) in themanner they will not be exposed to the impact exceeding the impactresistance described in the general specifications of this manual, as they areprecision devices. Failure to do so may cause the unit to fail.Compliance with EC directive (CE Marking)This note does not guarantee that an entire mechanical module produced inaccordance with the contents of this note will comply with the following standards.Compliance to EMC directive for the entire mechanical module should be checked bythe user / manufacturer. For more details please contact the local Mitsubishi Electricsales site.Attention This product is designed for use in industrial applications. Authorized Representative in the European Community:Mitsubishi Electric Europe B.V.Gothaer Str. 8, 40880 Ratingen, GermanyRequirement for Compliance with EMC directiveThe following products have shown compliance through direct testing (to the identifiedstandards) and design analysis (forming a technical construction file) to the EuropeanDirective for Electromagnetic Compatibility (2004/108/EC) when used as directed bythe appropriate documentation.Type :Programmable Controller (Open Type Equipment)For more details please contact the local Mitsubishi Electric sales site.Associated ManualsThe following manuals are relevant to this product. When these loose manuals arerequired, please consult with our local distributor.Bundled ItemsStandard RemarkEN61131-2 : 2007Programmablecontrollers-Equipment,requirement and testsEMI Compliance with all relevant aspects of thestandard. (Radiated Emissions)EMSCompliance with all relevant aspects of thestandard.(ESD, RF electromagnetic field, EFTB, Surge, RFconducted disturbances and Power frequencymagnetic field)Manual name ContentsManualNumber(Model Code)GT10 User's ManualDescribes the GT10 hardware-relevantcontent such as part names, externaldimensions, mounting, power supplywiring, specifications, and introduction tooption devices.(sold separately)JY997D24701(09R819)GT Designer2Version2 BasicOperation/DataTransfer Manual(For GOT1000 Series)Describes methods of the GT Designer2installation operation, basic operation fordrawing and transmitting data toGOT1000 series(sold separately)SH-080529ENG(1D7M24)GT Designer3Version1 ScreenDesign Manual(For GOT1000 Series)(Fundamentals)Describes methods of the GT Designer3installation operation, basic operation fordrawing and transmitting data toGOT1000 series(sold separately)SH-080866ENG(1D7MB9)Bundled item QuantityGT10-LDR memory loader 1USB cable (1m) 1GT10-LDR Memory loader USER'S MANUAL (This manual) 11. OverviewGT10-LDR memory loader is the memory transfer module that reads/writes the data to GT10 or between a PC (GT Designer2 Ver.2.77F or later, GT Designer3 Ver.1.01B orlater) and GT10-LDR.*1 When GT10-LDR is connected to a PC via the USB hub, the power supply of the USB hub must be supplied by the AC adopter of the USB hub.GT10-LDR connected to the USB hub may not work properly depending on the PC environment. In the case, connect the GT10-LDR directly to the USB port on the PC.2. Specifications2.1 General Specifications*1 The wet bulb temperature is 39C or less.*2 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a malfunction.When the air inside the control panel is purged by pressurization, the surface sheet may be lifted by high pressure. As a result, the touch panel may be difficult to press,and the sheet may be peeled off.*3 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and themachinery within the premises.Category II applies to equipment for which electrical power is supplied from fixed facilities.The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.*4 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.2.2 Performance Specifications*1 ROM in which new data can be written without deleting the written data.Item SpecificationsOperating ambient temperature 0 to 40CStorage ambient temperature -20 to 60COperating ambient humidity *1 10 to 90% RH, non-condensingStorage ambient humidity *1 10 to 90% RH, non-condensingVibration resistanceConforms to JISB3502 andIEC61131-2Frequency Acceleration Half-amplitude Sweep CountUnder intermittentvibration5 to 9Hz -- 3.5mm10 times each in X, Yand Z directions9 to 150Hz 9.8m/s2 --Under continuousvibration5 to 9Hz -- 1.75mm9 to 150Hz 4.9m/s2 --Shock resistance Conforms to JIS B3502, IEC 61131-2 (147 m/s 2 , 3 times each in X, Y and Z directions)Operating atmosphere Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electro conductive dust particles and must be nodirect sunlight. (Same as for saving)Operating altitude *2 2000 m (6562 ft) max.Overvoltage category*3 II or lessPollution degree *4 2 or lessCooling method Self-coolingGT1020, GT1030PC(GT Designer2 Ver.2.77F or laterGT Designer3 Ver.1.01B or later)USB connectingcable (supplied)*1Item SpecificationsMemoryUser memory *1 Flash ROM 7.5MbyteLife (Number of writetimes) 100,000 timesLEDPOWER greenSET/RUN green/red/orangeERROR green/red/orangeItem SpecificationsSwitchRD/WR selectionswitch Paddle switchData selection switchENT keyTactile switchThe use of 100 thousand times is due forreplacement.(operating force 2.55N 0.69N)Write protection switch Slide switchExternal dimensions W70(2.75)H110(4.33)D21(0.82)[mm](inch)Weight 0.2kgGT10-LDR Memory loaderUser's ManualThis manual describes the part names, dimensions, mounting, and specificationsof the product. Before use, read this manual and manuals of relevant productsfully to acquire proficiency in handling and operating the product. Make sure tolearn all the product information, safety information, and precautions.And, store this manual in a safe place so that you can take it out and read itwhenever necessary. Always forward it to the end user.RegistrationThe company name and the product name to be described in this manual are theregistered trademarks or trademarks of each company.Effective April 2015Specifications are subject to change without notice. 2007 MITSUBISHI ELECTRIC CORPORATIONManual Number JY997D29501FDate April 2015