Mitsubishi Electric GT10 General Description Manual

Also see for GOT 1000 Series: Training manual Handbook Connection manual Manual Connection manual

SideASideBJAPANESEENGLISHJY997D31001NSideBSafety Precaution (Read these precautions before using.)Before using this product, please read this manual and the relevant manuals introducedin this manual carefully and pay full attention to safety to handle the product correctly.The precautions given in this manual are concerned with this product.In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".Depending on circumstances, procedures indicated by "CAUTION" may also belinked to serious results.In any case, it is important to follow the directions for usage.Indicates that incorrect handling may cause hazardousconditions, resulting in death or severe injury.Indicates that incorrect handling may cause hazardousconditions, resulting in medium or slight personal injuryor physical damage.DESIGN PRECAUTIONS Some failures of the GOT or cable may keep the outputs on or off.An external monitoring circuit should be provided to check for output signalswhich may lead to a serious accident.Not doing so can cause an accident due to false output or malfunction. If a communication fault (including cable disconnection) occurs duringmonitoring on the GOT, communication between the GOT and PLC CPU issuspended and the GOT becomes inoperative.A system where the GOT is used should be configured to perform anysignificant operation to the system by using the switches of a device otherthan the GOT on the assumption that a GOT communication fault will occur.Not doing so can cause an accident due to false output or malfunction. Do not use the GOT as the warning device that may cause a serious accident.An independent and redundant hardware or mechanical interlock is required toconfigure the device that displays and outputs serious warning.Failure to observe this instruction may result in an accident due to incorrectoutput or malfunction. Incorrect operation of the touch switch(s) may lead to a serious accident if theGOT backlight is gone out. When the GOT backlight goes out, causes themonitor screen to appear blank, while the input of the touch switch(s) remainsactive. This may confuse an operator in thinking that the GOT is in"screensaver" mode, who then tries to release the GOT from this mode bytouching the display section, which may cause a touch switch to operate.DESIGN PRECAUTIONS Do not bundle the control and communication cables with main-circuit, poweror other wiring.Run the above cables separately from such wiring and keep them a minimumof 100mm (3.94in.) apart. Not doing so noise can cause a malfunction. Do not press the GOT display section with a pointed material as a pen ordriver. Doing so can result in a damage or failure of the display section. Before connecting to GOT, turn ON the controller to enable thecommunication. When the communication of controller is not available, acommunication error may occur in GOT.MOUNTING PRECAUTIONS Be sure to shut off all phases of the external power supply used by the systembefore mounting or removing the GOT to/from the panel.Not doing so can cause the unit to fail or malfunction. When installing the battery wear an earth band etc. to avoid the static electricity.The static electricity can cause the unit to fail or malfunction.MOUNTING PRECAUTIONS Use the GOT in the environment that satisfies the general specificationsdescribed in this manual. Not doing so can cause an electric shock, fire,malfunction or product damage or deterioration. When mounting the GOT to the control panel, tighten the mounting screws in thespecified torque range. Undertightening can cause the GOT to drop, short circuitor malfunction, and deteriorate the waterproof effect and oilproof effect.Overtightening can cause a drop, short circuit or malfunction due to the damageof the screws or the GOT, and deteriorate the waterproof effect and oilproof effectdue to distortion of the protective cover for oil, GOT or panel. When using the GOT in the environment of oil or chemicals, use the protectivecover for oil. Failure to do so may cause failure or malfunction due to the oil orchemical entering into the GOT.WIRING PRECAUTIONS Be sure to shut off all phases of the external power supply used by the systembefore wiring. Failure to do so may result in an electric shock, product damage ormalfunctions. Please make sure to ground FG terminal of the GOT power supply section byapplying 100 or less which is used exclusively for the GOT. Not doing so maycause an electric shock or malfunction. Correctly wire the GOT power supply section after confirming the rated voltageand terminal arrangement of the product. Not doing so can cause a fire or failure. Tighten the terminal screws of the GOT power supply section in the specifiedtorque range. Undertightening can cause a short circuit or malfunction.Overtightening can cause a short circuit or malfunction due to the damage of thescrews or the GOT. Exercise care to avoid foreign matter such as chips and wire offcuts entering theGOT. Not doing so can cause a fire, failure or malfunction.WIRING PRECAUTIONS Plug the communication cable into the connector of the connected unit andtighten the mounting and terminal screws in the specified torque range.Undertightening can cause a short circuit or malfunction. Overtightening cancause a short circuit or malfunction due to the damage of the screws or unit.TEST OPERATIONPRECAUTIONS Before performing the test operations of the user creation monitor screen (such asturning ON or OFF bit device, changing the word device current value, changingthe settings or current values of the timer or counter), read through the manualcarefully and make yourself familiar with the operation method.During test operation, never change the data of the devices which are used toperform significant operation for the system. False output or malfunction cancause an accident.STARTUP/MAINTENANCEPRECAUTIONS When power is on, do not touch the terminals.Doing so can cause an electric shock or malfunction. Connect the battery correctly. Do not discharge, disassemble, heat, short, solder orthrow the battery into the fire. Incorrect handling may cause the battery togenerate heat, burst or take fire, resulting in injuries or fires. Before starting cleaning or terminal screw retightening, always switch off thepower externally in all phases. Not switching the power off in all phases can causea unit failure or malfunction. Undertightening can cause a short circuit ormalfunction. Overtightening can cause a short circuit or malfunction due to thedamage of the screws or unit.STARTUP/MAINTENANCEPRECAUTIONS Do not disassemble or modify the unit.Doing so can cause a failure, malfunction, injury or fire. Do not touch the conductive and electronic parts of the unit directly.Doing so can cause a unit malfunction or failure. The cables connected to the unit must be run in ducts or clamped.Not doing so can cause the unit or cable to be damaged due to the dangling,motion or accidental pulling of the cables or can cause a malfunction due to acable connection fault. When unplugging the cable connected to the unit, do not hold and pull the cableportion. Doing so can cause the unit or cable to be damaged or can cause amalfunction due to a cable connection fault.Compliance with EC directive (CE Marking)This note does not guarantee that an entire mechanical module produced in accordancewith the contents of this note will comply with the following standards. Compliance toEMC directive for the entire mechanical module should be checked by the user/manufacturer. For more details please contact the local Mitsubishi Electric sales site.Attention This product is designed for use in industrial applications.Requirement for Compliance with EMC directiveThe following products have shown compliance through direct testing (to theidentified standards) and design analysis (forming a technical construction file) to theEuropean Directive for Electromagnetic Compatibility (2004/108/EC) when used asdirected by the appropriate documentation.Type :Programmable Controller (Open Type Equipment)For more details please contact the local Mitsubishi Electric sales site.Notes for compliance to EMC regulation1) General notes on the use of communication cablesAny device which utilizes a data communication function is susceptible to thewider effects of local EMC noise. Therefore, when installing any communicationcables care should always be taken with the routing and location of those cables.The GOT units identified on the previous chapter are compliant with the EMCrequirement when the following communication cables are used.2) General notes on Power supplyThe GT1055-QSBD and GT1050-QBBD unitrequires an additional ferrite filter to be attached tothe 24V DC power supply cables. The filter shouldbe attached in a similar manner as shown in thefigure opposite, i.e. the power cables are wrappedaround the filter. However, as with all EMCsituations the more correctly applied precautionst h e b e t t e r t h e s y s t e m s E l e c t r o - m a g n e t i cCompatibility. The ferrite recommended is a TDKZCAT3035-1330 or similar. The ferrite should beplaced as near to the 24V DC terminals of theGT1055-QSBD and GT1050-QBBD as possible(wh ich s houl d be wi thin 75 mm of the GO Tterminal).Associated ManualsThe following manuals are relevant to this product. When these loose manuals arerequired, please consult with our local distributor.*1 Stored in the GT Works2/GT Designer2/GT Works3/GT Designer3 in PDFformat.For details of a PLC to be connected, refer to the PLC user's manual respectively.Bundled Items「电器电子产品有害物质限制使用标识要求」的表示方式Note: This symbol mark is for China only.含有有害6物质的名称，含有量，含有部品本产品中所含有的有害 6 物质的名称，含有量，含有部品如下表所示。STARTUP/MAINTENANCEPRECAUTIONS Do not drop or apply any impact to the battery.If any impact has been applied, discard the battery and never use it.The battery may be damaged by the drop or impact. Before touching the unit, always touch grounded metal, etc. to discharge staticelectricity from human body, etc.Not doing so can cause the unit to fail malfunction. Replace battery with GT11-50BAT by Mitsubishi electric Co. only.Use of another battery may present a risk of fire or explosion. Dispose of used battery promptly.Keep away from children. Do not disassemble and do not dispose of in fire.DISPOSAL PRECAUTIONS When disposing of the product, handle it as industrial waste. When disposing of batteries, separate them from other wastes according to thelocal regulations. (For details of the battery directive in EU member states, referGOT User's Manual.)TRANSPORTATIONPRECAUTIONS When transporting lithium batteries, make sure to treat them based on thetransport regulations. (Refer to User's Manual for details of the reguratedmodels.) Before transporting the GOT, turn the GOT power on and check that the batteryvoltage status is normal on the Time setting & display screen (utilities screen). Inaddition, confirm that the adequate battery life remains on the rating plate.Transporting the GOT with the low battery voltage or the battery the reachedbattery life may unstabilize the backup data unstable during transportation. Make sure to transport the GOT main unit and/or relevant unit(s) in the mannerthey will not be exposed to the impact exceeding the impact resistancedescribed in the general specifications of this manual, as they are precisiondevices. Failure to do so may cause the unit to fail.Check if the unit operates correctly after transportation.Standard RemarkEN61131-2 : 2007Programmablecontrollers- Equipment,requirement and testsEMI Compliance with all relevant aspects of thestandard. (Radiated Emissions)EMSCompliance with all relevant aspects of thestandard. (ESD, RF electromagnetic field, EFTB,Surge, RF conducted disturbances and Powerfrequency magnetic field)GOT Unit Existing Cables User Made CablesGT1055-QSBDandGT1050-QBBDGT01-C30R4-8Pmodified asshown in EX.1Those cables need to be independentlytested by the user to demonstrate EMCcompatibility when they are used withM i t s u b i s h i G O T u n i t a n d F X 3 UProgrammable Controllers.100mm250mm140mmGT01-C30R4-8PComes equippedAdded by userGOT unitsProgrammablecontrollerAdded by user(9.84inch) (3.93inch)(5.51inch)Ex.1F = Ferrite coreEx. NEC TOKIN - ESD-R-17S or similarF F FManual name ContentsManualNumber(Model Code)GT10 User's Manual(sold separately)Describes the GT10 hardware-relevantcontent such as part names, externaldimensions, mounting, power supplywiring, specifications, and introduction tooption devicesJY997D24701(09R819)GOT1000 SeriesConnection Manual1/3, 2/3, 3/3(sold separately) *1Describes system configurations of thec o n n e c t i o n m e t h o d a p p l i c a b l e t oGOT1000 series and cable creationmethodSH-080532ENG(1D7M26)GT Designer2 Version 2Basic Operation/DataTransfer Manual(For GOT1000 Series)(sold separately) *1Describes methods of the GT Designer2installation operation, basic operation ford r a w i n g a n d t r a n s m i t t i n g d a t a t oGOT1000 seriesSH-080529ENG(1D7M24)GT Designer2 Version2Screen Design Manual(For GOT1000 Series)1/3, 2/3, 3/3(sold separately) *1Describes specifications and settings oft h e o b j e c t f u n c t i o n s u s e d i n G TDesigner2SH-080530ENG(1D7M25)GT Designer3 Version1Screen Design Manual(For GOT1000 Series)(Fundamentals) 1/2, 2/2(sold separately) *1Describes methods of the GT Designer3installation operation, basic operation ford r a w i n g a n d t r a n s m i t t i n g d a t a t oGOT1000 seriesSH-080866ENG(1D7MB9)GT Designer3 Version1Screen Design Manual(For GOT1000 Series)(Functions) 1/2, 2/2(sold separately) *1Describes specifications and settings oft h e o b j e c t f u n c t i o n s u s e d i n G TDesigner3SH-080867ENG(1D7MC1)Model Name RemarkGT1055-QSBD GOT main unit(The maintenance supplies below are packed with the product.)GT1050-QBBDMaintenance Supplies QuantityPanel Mounting Bracket (with M4  20 screws) 4Panel Mounting Packing 1GT10 General Description (This manual) 1Up to75mm(2.95inch)GT1055-QSBD, GT1050-QBBDGT10 General DescriptionThis manual describes the specifications of the product. Before use, read thismanual and manuals of relevant products fully to acquire proficiency in handlingand operating the product. Make sure to learn all the product information, safetyinformation, and precautions.And, store this manual in a safe place so that you can take it out and read itwhenever necessary. Always forward it to the end user.RegistrationThe company name and the product name to be described in this manual are theregistered trademarks or trademarks of each company.Effective: Jul. 2019Specifications are subject to change without notice. 2008 MITSUBISHI ELECTRIC CORPORATIONManual Number JY997D31001NDate Jul. 2019

/ 3

Related manuals for Mitsubishi Electric GOT 1000 Series