Mitsubishi Electric GOT1000 User Manual

Also see for GOT 1000 Series: Training manual Handbook Connection manual Manual Connection manual

SideASideBJAPANESEENGLISHJY997D40401ESideBSafety Precaution (Read these precautions before using.)Before using this product, please read this manual and the relevant manualsintroduced in this manual carefully and pay full attention to safety to handle theproduct correctly.The precautions given in this manual are concerned with this product.In this manual, the safety precautions are ranked as and .Depending on circumstances, procedures indicated by may also belinked to serious results.In any case, it is important to follow the directions for usage.Indicates that incorrect handling may cause hazardousconditions, resulting in death or severe injury.Indicates that incorrect handling may cause hazardousconditions, resulting in medium or slight personal injury orphysical damage.DESIGN PRECAUTIONS Some failures of the GOT or cable may keep the outputs on or off.An external monitoring circuit should be provided to check for output signalswhich may lead to a serious accident.Not doing so can cause an accident due to false output or malfunction. If a communication fault (including cable disconnection) occurs duringmonitoring on the GOT, communication between the GOT and PLC CPU issuspended and the GOT becomes inoperative.A system where the GOT is used should be configured to perform anysignificant operation to the system by using the switches of a device otherthan the GOT on the assumption that a GOT communication fault will occur.Not doing so can cause an accident due to false output or malfunction. Do not use the GOT as the warning device that may cause a seriousaccident. An independent and redundant hardware or mechanical interlock isrequired to configure the device that displays and outputs serious warning.Failure to observe this instruction may result in an accident due to incorrectoutput or malfunction. Incorrect operation of the touch switch(s) may lead to a serious accident if theGOT backlight is gone out. When the GOT backlight goes out, the POWERLED flickers (green/orange) and the display section turns black and causesthe monitor screen to appear blank, while the input of the touch switch(s)remains active. This may confuse an operator in thinking that the GOT is in"screensaver" mode, who then tries to release the GOT from this mode bytouching the display section, which may cause a touch switch to operate.Note that the following occurs on the GOT when the backlight goes out.- The POWER LED flickers (green/orange) and the monitor screen appearsblank.DESIGN PRECAUTIONS Do not bundle the control and communication cables with main-circuit, power orother wiring. Run the above cables separately from such wiring and keep them aminimum of 100mm (3.94in.) apart.Not doing so noise can cause a malfunction.MOUNTING PRECAUTIONS Make sure to turn off the Connector Conversion Box's power before attaching ordetaching it to/from the GOT.Failure to do so may cause unit failure or malfunctions.MOUNTING PRECAUTIONS Use the Connector Conversion Box within the generic environment specificationsdescribed in this manual. If the product is used in such conditions, electric shock,fire, malfunctions, deterioration or damage may occur.WIRING PRECAUTIONS Be sure to shut off all phases of the external power supply used by the systembefore wiring. Failure to do so may result in an electric shock, product damage ormalfunctions. Please make sure to ground FG terminal of the Connector Conversion Box powersupply section by applying 100 or less which is used exclusively for the GOT. Notdoing so may cause an electric shock or malfunction. Correctly wire the Connector Conversion Box power supply section afterconfirming the rated voltage and terminal arrangement of the GOT. Not doing socan cause a fire or failure. Exercise care to avoid foreign matter such as chips and wire offcuts entering theGOT. Not doing so can cause a fire, failure or malfunction.WIRING PRECAUTIONS Plug the communication cable into the connector of the connected unit andtighten the mounting and terminal screws in the specified torque range.Undertightening can cause a short circuit or malfunction. Overtightening cancause a short circuit or malfunction due to the damage of the screws or unit.TEST OPERATIONPRECAUTIONS Before performing the test operations of the user creation monitor screen (such asturning ON or OFF bit device, changing the word device current value, changingthe settings or current values of the timer or counter, and changing the buffermemory current value), read through the manual carefully and make yourselffamiliar with the operation method. During test operation, never change the dataof the devices which are used to perform significant operation for the system.False output or malfunction can cause an accident.STARTUP/MAINTENANCEPRECAUTIONS When power is on, do not touch the terminals.Doing so can cause an electric shock or malfunction. Before starting cleaning or terminal screw retightening, always switch off thepower externally in all phases. Not switching the power off in all phases can causea unit failure or malfunction. Undertightening can cause a short circuit ormalfunction. Overtightening can cause a short circuit or malfunction due to thedamage of the screws or unit.STARTUP/MAINTENANCEPRECAUTIONS Do not disassemble or modify the unit.Doing so can cause a failure, malfunction, injury or fire. Do not touch the conductive and electronic parts of the unit directly.Doing so can cause a unit malfunction or failure. The cables connected to the unit must be run in ducts or clamped.Not doing so can cause the unit or cable to be damaged due to the dangling,motion or accidental pulling of the cables or can cause a malfunction due to acable connection fault. When unplugging the cable connected to the unit, do not hold and pull the cableportion. Doing so can cause the unit or cable to be damaged or can cause amalfunction due to a cable connection fault.DISPOSAL PRECAUTIONS When disposing of the product, handle it as industrial waste.Certification of UL, cUL standardsUL, cUL Standards are recognized in use by the following combination. GT1665HS-VTBD (Hardware version F or later) GT16H-CNB-42S External cable (GT16H-C30-42P, GT16H-C60-42P, GT16H-C100-42P)General notes on power supplyThis equipment must be supplied by a UL Listed or Recognized 24 V dc ratedpower supply and UL Listed or Recognized fuse rated not higher than 4A, or a ULListed Class 2 power supply.Compliance with EC directive (CE Marking)This note does not guarantee that an entire mechanical module produced inaccordance with the contents of this note will comply with the following standards.Compliance to EMC directive for the entire mechanical module should be checked bythe user/manufacturer. For more details please contact the local Mitsubishi Electricsales site.Attention This product is designed for use in industrial applications. Authorized Representative in the European Community:Mitsubishi Electric Europe B.V.Gothaer Str. 8, 40880 Ratingen, GermanyRequirement for Compliance with EMC directiveThe following products have shown compliance through direct testing (to theidentified standards) and design analysis (forming a technical construction file) to theEuropean Directive for Electromagnetic Compatibility (2004/108/EC) when used asdirected by the appropriate documentation.Type: Programmable Controller (Open Type Equipment)For more details please contact the local Mitsubishi Electric sales site.Notes for compliance to EMC regulation1) General notes on the control panelMake sure to combine the GT16 Handy GOT with the Connector ConversionBox to comply with the EMC directive. The Connector Conversion Box is anopen type device (device installed to another device) and must be installed in aconductive control panel.2) General notes on the use of communication cables External cable (GT16H-C30-42P, GT16H-C60-42P, GT16H-C100-42P) Direct connection cable Ethernet connection cable (Shielded twisted pair cable (STP)) PLC (manufactured by other company), microcomputer, temperaturecontroller, inverter, servo amplifier, CNC, MODBUS(R)/RTU or MODBUS(R)/TCP connectionProduce the cable (RS-232 cable, RS-422 / 485 cable) for connecting the GOTto a controller with reference to the following manual. GOT1000 Series Connection Manual for GT Works3 and a controller used3) General notes on Power supplyThe Connector Conversion Box requires anadditional ferrite filter to be attached to the24V DC power supply cables. The filtershould be attached in a similar manner asshown in the figure opposite, i.e. the powerc a b l e s a r e w r a p p e d a r o u n d t h e f i l t e r.However, as with all EMC situations the morecorrectly applied precautions the better thesystems Electro-magnetic Compatibility. Theferrite recommended is a TDK ZCAT3035-1330 or similar. The ferrite should be placedas near to the 24V DC terminals of theConnector Conversion Box as possible (whichshould be within 75mm of the GOT terminal).Associated ManualsThe following manuals are relevant to this product. When these loose manuals arerequired, please consult with our local distributor.For details of a PLC to be connected, refer to the PLC user's manual respectively.Bundled Items1. FeaturesThe Connector Conversion Box relays the GOT's external 42-pin connector to thepower supply/switch and the PLC's connector and terminal block, while enablingusers to operate the Handy GOT outside the enclosure.2. SpecificationsGeneral SpecificationsOther specifications are the same as the GT16 Handy GOT main unit.TRANSPORTATIONPRECAUTIONS The Connector Conversion Box is a precision instrument. During transportation,avoid impacts larger than those specified in this manual. Failure to do so maycause failures in the unit. After transportation, verify the operations of the unit.Standard RemarkEN61131-2 : 2007P r o g r a m m a b l econtrollers- Equipment,requirement and testsEMI Compliance with all relevant aspects of thestandard. (Radiated Emissions)EMSCompliance with all relevant aspects of thestandard. (ESD, RF electromagnetic field, EFTB,Surge, RF conducted disturbances and Powerfrequency magnetic field)Existing Cables User Made CablesGT01-C30R4-8PGT11H-C30R2-6PThe cable need to be independently tested by the user todemonstrate EMC compatibility when they are used withthe GOT, the PLC of MELSEC-Q series, MELSEC-L series,MELSEC-QnA, MELSEC-A series and MELSEC-FX series.Up to 75mm(2.95inch)TDKManual name Contents Manual Number(Model Code)G T 1 6 H a n d yG O T U s e r ' sManual(Hardware/Utility,Connection)1/2, 2/2(sold separately)Describes the Handy GOT hardware-relevant content such as part names,external dimensions, mounting, powers u p p l y w i r i n g , s p e c i f i c a t i o n s , a n dintroduction to option devicesJY997D41201JY997D41202(09R821)Bundled item QuantityGT16H-CNB-42S Connector conversion box 1Packing for panel installation 1Flange for GT10-9PT5S 1Screws for flange installation (M3×8) 2CONNECTOR CONVERSION BOX GT16H-CNB-42S User’sManual (This manual) 1Item SpecificationsOperatingambienttemperature0 to 55CStorageambienttemperature-20 to 70CVibrationresistance WheninstallingDIN railFrequency Acceleration Half-amplitudeSweepCount5 to 9Hz -- 1.75mm 10 timeseach in X, Yand Zdirections9 to 150Hz 4.9m/s 2 --OperatingatmosphereMust be free of lamp black, corrosive gas, flammable gas, orexcessive amount of electroconductive dust particles and must be nodirect sunlight. (Same as for saving)Control panel oroperation panelPLCGT16H-CNB-42SConnector Conversion BoxHandy GOTExternal cableGT16H-C -42P(Option)CONNECTOR CONVERSION BOXGT16H-CNB-42SUser's ManualThis manual describes the part names, dimensions, mounting, and specificationsof the product. Before use, read this manual and manuals of relevant productsfully to acquire proficiency in handling and operating the product. Make sure tolearn all the product information, safety information, and precautions.And, store this manual in a safe place so that you can take it out and read itwhenever necessary. Always forward it to the end user.RegistrationEthernet is a registered trademark of Xerox Corporation in the United States.MODBUS is a trademark of Schneider Electric SA. The company name and theproduct name to be described in this manual are the registered trademarks ortrademarks of each company.Effective April 2015Specifications are subject to change without notice. 2010 MITSUBISHI ELECTRIC CORPORATIONManual Number JY997D40401EDate April 2015

/ 3

Related manuals for Mitsubishi Electric GOT 1000 Series