Mitsubishi Electric FR-800 Series Installation Manual

Also see for FR-A800: Instruction manual Safety stop function instruction manual Instruction manual Instruction manual Safety stop function instruction manual

Mitsubishi Electric Europe B.V. /// FA - European Business Group ///Germany /// Tel.: +49(0)2102-4862048 /// Fax: +49(0)2102-4861120 ///https://eu3a.mitsubishielectric.comInstallation manual for CC-Link IE TSNInterface Option Unit FR-A8NCGArt.no.: 503423 ENG, Version A, 18082020Safety InformationFor qualified staff onlyThis manual is only intended for use by properly trained and qualified electri-cal technicians who are fully acquainted with automation technology safetystandards. All work with the hardware described, including system design,installation, setup, maintenance, service and testing, may only be performedby trained electrical technicians with approved qualifications who are fullyacquainted with the applicable automation technology safety standards andregulations.Proper use of equipmentThe frequency inverters of the FR-A800 and FR-F800 series are only intendedfor the specific applications explicitly described in this manual and the manu-als listed below. Please take care to observe all the installation and operatingparameters specified in the manuals. Only accessories and peripherals specifi-cally approved by Mitsubishi Electric may be used. Any other use or applica-tion of the products is deemed to be improper.Relevant safety regulationsAll safety and accident prevention regulations relevant to your specific appli-cation must be observed in the system design, installation, setup, mainte-nance, servicing and testing of these products.In this manual special warnings that are important for the proper and safe useof the products are clearly identified as follows:Further InformationThe following manuals contain further information about the devices:● Instruction manual of the frequency inverter FR-A800● Instruction manual of the frequency inverter FR-F800● Instruction manual of the plug-in option FR-A8NCG● Beginner’s Guide of the frequency inverter FR-A800● Installation Guide of the frequency inverter FR-A800● Installation Guide of the frequency inverter FR-F800These manuals are available free of charge through the internet:https://eu3a.MitsubishiElectric.com/fa/en/If you have any questions concerning the programming and operation of theequipment described in this manual, please contact your relevant sales officeor department.General DescriptionWith the CC-Link IE TSN interface adapter, the FR-A800 and FR-F800 series fre-quency inverters can be connected to an CC-Link IE TSN network by using a RJ45connector.Important InformationPlease observe all the following warnings and information to ensure that theoption unit is installed correctly.Installing the Plug-in OptionThe following operation steps describe the physical installation of the optionunit. You will find a detailed description how to mount the interface optionunit in the FR-A8NCG instruction manual and the FR-A800 and FR-F800 fre-quency inverter instruction manuals. Unfasten the lower screws on the front of the inverter and remove the frontlower cover. Remove the front top cover in the same manner. Insert three spacers into the mounting holes that will not be filled withmounting screws. Fit the board mounted option connector on this product to the guide ofthe option connector on the inverter and insert the plug-in option as far asit goes. (Select option connector 1 on the inverter.) Fasten the earth plate to the inverter using the one mounting screwthrough the hole on the left side. Fasten this product to the inverter using the one mounting screw throughthe hole on the left side. Fasten the earth plate and this product to theinverter using the last screw through the hole on the right side of the earthplate and this product. Connect the Ethernet cables to the network connectors on the option unit.PORT1 and PORT2 do not need to be distinguished.When only one connector is used in star topology, either PORT1 or PORT2is applicable.When using two connectors for line topology, an Ethernet cable can beconnected to the connectors in any combination. For example, the cablecan be connected between PORT1s or between PORT1 and PORT2.Cut off the hooks on the rear of the inverter front cover with a nipper etc.,and remove the lid. Place the Communication option LED display cover inthe empty position.Reinstall the front covers, giving safe passage for the network cables. Theoption unit is now installed and ready for configuration.Attach power cable and supply power to configure the inverter and theoption unit.Package ContentsFrequencyInvertersP DANGER:Personnel health and injury warnings.Failure to observe the precautions described here can resultin serious health and injury hazards.E CAUTION:Equipment and property damage warnings.Failure to observe the precautions described here can resultin serious damage to the equipment or other property.P DANGER● Cut off all phases of the power source externally before starting theinstallation or wiring work, thus avoiding electric shock or damages tothe product.● After disconnecting the power wait for at least 10 minutes beforeinstalling option units to allow the power capacitors in the inverter todischarge to a safe level.● The inverter must be grounded with a proper earth connector con-forming to all national and local safety regulations and standards (JIS,NEC Section 250, IEC 61140 Class 1 and other standards).● Do not remove any components unless explicitly instructed to do so inthis manual. Failure to observe this warning can result in damage tothe inverter.E WARNING● Only operate the inverter and the option units within the environmen-tal parameters specified in the inverter manual. Take steps to ensurethat neither the inverter nor the option units are exposed to dust, oilspray, corrosive and flammable gases, intense vibrations and physicalshocks, high temperatures, condensation or damp.● When drilling screw holes or wiring, cutting chips or wire chips shouldnot enter ventilation slits. Such an accident may cause fire, failure ormalfunction.● Do not touch any of the inverter‘s live components, such as the connec-tion terminals or plug connectors.● The inverter housing gets very hot during operation. To avoid burnsdo not touch the inverter when it is turned on and wait for a shortperiod after its power supply has been switched off before touchingthe housing.● To avoid damage due to static electricity, static electricity in your bodymust be discharged before you touch the product.NOTEWhen a communication option is installed to the FR-A800-E/FR-F800-E seriesinverter, use the earthing (grounding) cable supplied with the inverter insteadof the earth plate supplied with the communication option.Inverter side option connectorSpacerSpacerSpacerEarth plateMounting screwSpacerSpacerMounting screwMounting screwConnector 2Connector 3Connector 1Do not insert theplug-in option toconnector 2 or 3.SpacerEarth plateItem No. of piecesPCB board 1M3 x 8 mm screw 3Board spacer 3Communication option LED display cover 1Earth plate 1Connectors forcommunicationTo the nextconnector forcommunication(PORT2)Connection betweenPORT1 and PORT1, PORT2 and PORT2Connection betweenPORT1 and PORT2(PORT2) (PORT1)To the nextconnector forcommunication(PORT2)Connectors forcommunication(PORT2) (PORT1)Connectors forcommunication(PORT2) (PORT1)Connectors forcommunication(PORT2) (PORT1)HooksHooksCommunication option LED display cover