Makita RP1800 Instruction Manual

Also see for RP1800: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

9 ENGLISHENGLISH (Original instructions)SPECIFICATIONSModel RP1800/RP1800FRP1801/RP1801FRP2300FC RP2301FCCollet chuck capacity 12 mm or 1/2"Plunge capacity 0 - 70 mmNo load speed (min -1 ) 22,000 9,000 - 22,000Overall length 312 mmNet weight 6.0 kg 6.1 kgSafety class /II• Due to our continuing programme of research and development, the specifications herein are subject to changewithout notice.• Note: Specifications may differ from country to country.• Weight according to EPTA-Procedure 01/2003Intended useThe tool is intended for flush trimming and profiling ofwood, plastic and similar materials.Power supplyThe tool should be connected only to a power supply of thesame voltage as indicated on the nameplate, and can only beoperated on single-phase AC supply. They are double-insu-lated in accordance with European Standard and can, there-fore, also be used from sockets without earth wire.For Model RP1800For public low-voltage distribution systems ofbetween 220 V and 250 V.Switching operations of electric apparatus cause volt-age fluctuations. The operation of this device underunfavorable mains conditions can have adverse effectsto the operation of other equipment. With a mainsimpedance equal or less than 0.40 Ohms it can be pre-sumed that there will be no negative effects. The mainssocket used for this device must be protected with afuse or protective circuit breaker having slow trippingcharacteristics.For Model RP1800FFor public low-voltage distribution systems ofbetween 220 V and 250 V.Switching operations of electric apparatus cause volt-age fluctuations. The operation of this device underunfavorable mains conditions can have adverse effectsto the operation of other equipment. With a mainsimpedance equal or less than 0.39 Ohms it can be pre-sumed that there will be no negative effects. The mainssocket used for this device must be protected with afuse or protective circuit breaker having slow trippingcharacteristics.For Model RP1801,RP1801FFor public low-voltage distribution systems ofbetween 220 V and 250 V.Switching operations of electric apparatus cause volt-age fluctuations. The operation of this device underunfavorable mains conditions can have adverse effectsto the operation of other equipment. With a mainsimpedance equal or less than 0.38 Ohms it can be pre-sumed that there will be no negative effects. The mainssocket used for this device must be protected with afuse or protective circuit breaker having slow trippingcharacteristics.For Model RP1800,RP1800F,RP1801,RP1801FNoiseThe typical A-weighted noise level determined accord-ing to EN60745:Sound pressure level (LpA ) : 86 dB(A)Sound power level (LWA ) : 97 dB(A)Uncertainty (K) : 3 dB(A)Wear ear protectionVibrationThe vibration total value (tri-axial vector sum) deter-mined according to EN60745:Work mode : cutting grooves in MDFVibration emission (ah ) : 4.0 m/s 2Uncertainty (K) : 1.5 m/s2For Model RP2300FC,RP2301FCNoiseThe typical A-weighted noise level determined accord-ing to EN60745:Sound pressure level (LpA ) : 87 dB(A)Sound power level (LWA ) : 98 dB(A)Uncertainty (K) : 3 dB(A)Wear ear protectionVibrationThe vibration total value (tri-axial vector sum) deter-mined according to EN60745:Work mode : cutting grooves in MDFVibration emission (ah ) : 4.5 m/s 2Uncertainty (K) : 1.5 m/s2NOTE: The declared vibration emission value hasbeen measured in accordance with the standard testmethod and may be used for comparing one tool withanother.NOTE: The declared vibration emission valuemay also be used in a preliminary assessment ofexposure.