Makita RP1110CJ Instruction Manual

Also see for RP0910: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

5ENGLISH (Original instructions)Explanation of general view1 Adjusting knob2 Stopper pole3 Depth pointer4 Stopper pole setting nut5 Lock knob6 Fast-feed button7 Adjusting hex bolt8 Stopper block9 Nylon nut10 Lock button11 Switch trigger12 Speed adjusting dial13 Collet nut14 Wrench15 Shaft lock16 Tighten17 Loosen18 Correct size collet cone19 Workpiece20 Bit revolving direction21 Feed direction22 View from the top of the tool23 Straight guide24 Lock screw25 Guiding surface26 Templet guide27 Screw28 Bit29 Base30 Templet31 Workpiece32 Distance (X)33 Outside diameter of the templetguide34 Nozzle assembly35 Dust nozzle assembly36 Limit mark37 Brush holder cap38 ScrewdriverSPECIFICATIONSModel RP0910 RP1110CMax. collet capacity ..................................................................... 8 mm or 1/4" 8 mm or 1/4"Plunge capacity ........................................................................... 0 – 57 mm 0 – 57 mmNo load speed (min–1) ................................................................. 27,000 8,000 – 24,000Overall height .............................................................................. 260 mm 260 mmNet weight .................................................................................... 3.3 kg 3.4 kgSafety class ................................................................................. /II /II• Due to our continuing program of research and devel-opment, the specifications herein are subject to changewithout notice.• Specifications may differ from country to country.• Weight according to EPTA-Procedure 01/2003 ENE010-1Intended useThe tool is intended for flush trimming and profiling ofwood, plastic and similar materials. ENF002-2Power supplyThe tool should be connected only to a power supply ofthe same voltage as indicated on the nameplate, and canonly be operated on single-phase AC supply. They aredouble-insulated and can, therefore, also be used fromsockets without earth wire. GEA010-1General Power Tool Safety WarningsWARNING Read all safety warnings and allinstructions. Failure to follow the warnings andinstructions may result in electric shock, fire and/orserious injury.Save all warnings and instructions for future refer-ence.GEB018-4ROUTER SAFETY WARNINGS1. Hold power tool by insulated gripping surfaces,because the cutter may contact its own cord.Cutting a “live” wire may make exposed metal partsof the power tool “live” and shock the operator.2. Use clamps or another practical way to secureand support the workpiece to a stable platform.Holding the work by your hand or against the bodyleaves it unstable and may lead to loss of control.3. Wear hearing protection during extended periodof operation.4. Handle the bits very carefully.5. Check the bit carefully for cracks or damagebefore operation. Replace cracked or damagedbit immediately.6. Avoid cutting nails. Inspect for and remove allnails from the workpiece before operation.7. Hold the tool firmly with both hands.8. Keep hands away from rotating parts.9. Make sure the bit is not contacting the work-piece before the switch is turned on.10. Before using the tool on an actual workpiece, letit run for a while. Watch for vibration or wobblingthat could indicate improperly installed bit.11. Be careful of the bit rotating direction and thefeed direction.12. Do not leave the tool running. Operate the toolonly when hand-held.13. Always switch off and wait for the bit to come toa complete stop before removing the tool fromworkpiece.14. Do not touch the bit immediately after operation;it may be extremely hot and could burn yourskin.15. Do not smear the tool base carelessly with thin-ner, gasoline, oil or the like. They may causecracks in the tool base.16. Use bits of the correct shank diameter suitablefor the speed of the tool.17. Some material contains chemicals which may betoxic. Take caution to prevent dust inhalationand skin contact. Follow material supplier safetydata.18. Always use the correct dust mask/respirator forthe material and application you are workingwith.SAVE THESE INSTRUCTIONS.