Makita CG100DSAX Instruction Manual

Also see for CG100D: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

10 ENGLISHInstalling or removing the rod and piston1. Insert the rod from the rear side of the tool with itsteeth facing down.► Fig.13: 1. Long rod or black rodNOTICE: For 600 ml size holder, use the longrod. For 800 ml size holder, use the black rod.2. Attach the piston with the screw.► Fig.14: 1. Screw 2. Piston 3. Long rod or black rodTo remove the rod and piston, follow the installationprocedure in reverse.Installing or removing 600 ml or 800ml size holderCAUTION: Secure the holder to the holderjoint firmly. Otherwise the holder may come offduring operation and may cause an injury.To install the holder, turn it clockwise firmly until it stopswhile holding the holder joint.► Fig.15: 1. HolderTo remove the holder, follow the installation procedurein reverse.OPERATIONUsing cartridgePreparing cartridge for use1. Cut the tip of the cartridge nozzle so that the suit-able amount of caulking material is fed.► Fig.16: 1. Nozzle2. Make a hole on the protective film with the tip ofthe nozzle.► Fig.17: 1. Nozzle3. Attach the nozzle to the cartridge.NOTICE: Be sure to check the cartridge fordamage before installation. Using the damagedcartridge may cause malfunction.NOTICE: When reusing the partially used car-tridge, be sure to remove the solid caulking mate-rial before the installation.Installing cartridge to 300 ml sizeholderNOTICE: Make sure that piston A is attachedto the rod. Do not use other type of piston forcartridge.1. Pull the rod handle backward slowly until it stops.► Fig.18: 1. Rod handle2. Insert the cartridge into the holder as shown in thefigure.► Fig.193. Push the rod gently until the piston touches thebottom of cartridge.To remove the cartridge, follow the installation proce-dure in reverse.Installing cartridge to 600 ml or 800ml size holderNOTICE: Make sure that piston A (for 600 mlsize holder) or piston D (for 800 ml size holder) isattached to the rod. Do not use other type of pis-ton for cartridge.1. Remove the holder cap from the holder, and thenpull the rod handle backward slowly until it stops.► Fig.20: 1. Holder cap 2. Rod handle2. Insert the cartridge into the holder.► Fig.21: 1. Holder3. Attach the holder cap by turning it firmly whileholding the holder.► Fig.22: 1. Holder cap 2. Holder4. Push the rod gently until the piston touches thebottom of cartridge.To remove the cartridge, follow the installation proce-dure in reverse.Using film type packagePreparing package for useCut off the tip of the package.► Fig.23NOTICE: Be sure to check the package for dam-age before installation. Using the damaged pack-age may cause malfunction.Installing film type package to 600 mlor 800 ml size holderNOTICE: Make sure that piston B (for 600 mlsize holder) or piston E (for 800 ml size holder) isattached to the rod. Do not use other type of pis-ton for film type package.1. Remove the holder cap, nozzle, and rubber ringfrom the holder.► Fig.24: 1. Holder cap 2. Nozzle 3. Rubber ring4. Holder2. Pull the rod handle backward slowly until it stops.3. Insert the package into the holder.► Fig.25: 1. Holder4. Attach the rubber ring, nozzle, and holder cap byturning the holder cap firmly.► Fig.26: 1. Holder cap 2. Nozzle 3. Rubber ring4. Holder5. Push the rod gently until the piston touches thepackage.To remove the package, remove the holder cap, nozzle,rubber ring, and then push the rod handle forward untilit stops.