Makita BLS713 Instruction Manual
Also see for BLS713: Instruction manualInstruction manualInstruction manualInstruction manualInstruction manual
1120. Disposal of battery.Ensure battery is disposed of safely as instructed bythe manufacturer.ADDITIONAL SAFETY RULESFOR TOOL ENB118-21. Wear eye protection.2. Keep hands out of path of saw blade. Avoidcontact with any coasting blade. It can still causesevere injury.3. Do not operate saw without guards in place.Check blade guard for proper closing before eachuse. Do not operate saw if blade guard does notmove freely and close instantly. Never clamp or tiethe blade guard into the open position.4. Do not perform any operation freehand. Theworkpiece must be secured firmly against the turnbase and guide fence with the vise during alloperations. Never use your hand to secure theworkpiece.5. Never reach around saw blade.6. Turn off tool and wait for saw blade to stop beforemoving workpiece or changing settings.7. Remove the battery cartridge before changingblade or servicing.8. Always secure all moving portions before carryingthe tool.9. Stopper pin which locks the cutter head down isfor carrying and storage purposes only and not forany cutting operations.10. Do not use the tool in the presence of flammableliquids or gases. The electrical operation of the toolcould create an explosion and fire when exposed toflammable liquids or gases.11. Check the blade carefully for cracks or damagebefore operation.Replace cracked or damaged blade immediately.12. Use only flanges specified for this tool.13. Be careful not to damage the arbor, flanges(especially the installing surface) or bolt. Damageto these parts could result in blade breakage.14. Make sure that the turn base is properly securedso it will not move during operation.15. For your safety, remove the chips, small pieces,etc. from the table top before operation.16. Avoid cutting nails. Inspect for and remove allnails from the workpiece before operation.17. Make sure the shaft lock is released before theswitch is turned on.18. Be sure that the blade does not contact the turnbase in the lowest position.19. Hold the handle firmly. Be aware that the sawmoves up or down slightly during start-up andstopping.20. Make sure the blade is not contacting theworkpiece before the switch is turned on.21. Before using the tool on an actual workpiece, let itrun for a while. Watch for vibration or wobblingthat could indicate poor installation or a poorlybalanced blade.22. Wait until the blade attains full speed beforecutting.23. Stop operation immediately if you notice anythingabnormal.24. Do not attempt to lock the trigger in the onposition.25. Be alert at all times, especially during repetitive,monotonous operations. Do not be lulled into afalse sense of security. Blades are extremelyunforgiving.26. Always use accessories recommended in thismanual. Use of improper accessories such asabrasive wheels may cause an injury.27. Do not use the saw to cut other than wood.28. Connect miter saws to a dust collecting devicewhen sawing.29. Select saw blades in relation to the material to becut.30. Take care when slotting.31. Replace the kerf board when worn.32. Do not use saw blades manufactured from highspeed steel.33. Some dust created from operation containschemicals known to cause cancer, birth defects orother reproductive harm. Some examples of thesechemicals are:• lead from lead-based-painted material and,• arsenic and chromium from chemically-treatedlumber.Your risk from these exposures varies,depending on how often you do this type ofwork. To reduce your exposure to thesechemicals: work in a well ventilated area andwork with approved safety equipment, such asthose dust masks that are specially designed tofilter out microscopic particles.34. To reduce the emitted noise, always be sure thatthe blade is sharp and clean.35. The operator is adequately trained in the use,adjustment and operation of the machine.36. Use correctly sharpened saw blades. Observe themaximum speed marked on the saw blade.37. Refrain from removing any cut-offs or other partsof the workpiece from the cutting area whilst thetool is running and the saw head is not in the restposition.38. Use only saw blades recommended by themanufacturer which conform to EN847-1.39. Wear gloves for handling saw blade (saw bladesshall be carried in a holder wherever practicable)and rough material.SAVE THESE INSTRUCTIONS.IMPORTANT SAFETYINSTRUCTIONS ENC007-7FOR BATTERY CARTRIDGE1. Before using battery cartridge, read allinstructions and cautionary markings on (1)battery charger, (2) battery, and (3) product usingbattery.2. Do not disassemble battery cartridge. |
Related manuals for Makita BLS713
Makita BLS713 Instruction Manual
Makita BLS713 Instruction Manual
Makita BLS713 Instruction Manual
Makita BLS712SF Instruction Manual
Makita DLS713 Instruction Manual
Makita DLS713 Instruction Manual
Makita DLS713 Instruction Manual
Makita DLS713 Instruction Manual
Makita DLS713 Instruction Manual
Makita DLS713 Instruction Manual
This manual is suitable for:
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved