Makita 6953 Instruction Manual

Also see for 6953: Instruction manual Instruction manual Instruction manual Parts Breakdown Instruction manual

616. Remove adjusting keys and wrenchesForm the habit of checking to see that keys andadjusting wrenches are removed from tool beforeturning it on.17. Avoid unintentional startingDon’t carry plugged-in tool with finger on switch.Be sure switch is off when plugging in.18. Outdoor use extension cordsWhen tool is used outdoors, use only extensioncords intended for use outdoors and so marked.19. Stay alertWatch what you are doing. Use common sense.Do not operate tool when you are tired.20. Check damaged partsBefore further use of the tool, a guard or otherpart that is damaged should be carefully checkedto determine that it will operate properly and per-form its intended function. Check for alignment ofmoving parts, binding of moving parts, breakageof parts, mounting, and any other conditions thatmay affect its operation. A guard or other partthat is damaged should be properly repaired orreplaced by an authorized service center unlessotherwise indicated elsewhere in this instructionmanual. Have defective switches replaced byand authorized service center. Do not use tool ifswitch does not turn it on and off.21. WarningThe use of any other accessory or attachmentother than recommended in this operatinginstruction or the catalog may present a risk ofpersonal injury.22. Have your tool repaired by an expertThis electric appliance is in accordance with therelevant safety rules. Repairing of electric appli-ances may be carried out only by experts other-wise it may cause considerable danger for theuser.ADDITIONAL SAFETY RULES FOR TOOLENB003-11. Hold tool by insulated gripping surfaces whenperforming an operation where the cutting toolmay contact hidden wiring or its own cord. Con-tact with a “live” wire will also make exposedmetal parts of the tool “live” and shock the oper-ator.2. Wear ear protectors.3. Check the socket carefully for wear, cracks ordamage before installation.4. Hold the tool firmly.5. Always be sure you have a firm footing.Be sure no one is below when using the tool inhigh locations.6. The proper fastening torque may differ depend-ing upon the kind or size of the bolt. Check thetorque with a torque wrench.SAVE THESE INSTRUCTIONS.OPERATING INSTRUCTIONSSelecting correct socketAlways use the correct size socket for bolts and nuts. Anincorrect size socket will result in inaccurate and incon-sistent fastening torque and/or damage to the bolt or nut.Installing or removing socketCAUTION:Always be sure that the tool is switched off andunplugged before installing or removing the socket.1. For socket without O-ring and pin (Fig. 1)To install the socket, push it onto the anvil of the tooluntil it locks into place.To remove the socket, simply pull it off.2. For socket with O-ring and pin (Fig. 2)Move the O-ring out of the groove in the socket andremove the pin from the socket. Fit the socket ontothe anvil of the tool so that the hole in the socket isaligned with the hole in the anvil. Insert the pinthrough the hole in the socket and anvil. Then returnthe O-ring to the original position in the socketgroove to retain the pin. To remove the socket, followthe installation procedures in reverse.Switch action (Fig. 3)CAUTION:Before plugging in the tool, always check to see that theswitch trigger actuates properly and returns to the “OFF”position when released.To start the tool, simply pull the switch trigger. Tool speedis increased by increasing pressure on the switch trigger.Release the swithch trigger to stop.Holding the tool (Fig. 3)Hold the tool only by the handle when performing anoperation.Do not touch the metal part.Reversing switch action (Fig. 4)CAUTION:• Always check the direction of rotation before operation.• Use the reversing switch only after the tool comes to acomplete stop. Changing the direction of rotationbefore the tool stops may damage the tool.This tool has a reversing switch to change the direction ofrotation. Depress the reversing switch lever from the Aside for clockwise rotation or from the B side for counter-clockwise rotation.HookThe hook is convenient for temporarily hanging the tool.This can be removed without using a tool. This can beinstalled on either side of the tool.Installing and removing hook (Fig. 5)Expand the upper part of the hook in both directions andremove it. To install the hook, follow the removal proce-dure in reverse.

/ 24

Related manuals for Makita 6953

Makita 6953 Instruction Manual

This manual is suitable for:

6953

Makita 6953 Instruction Manual

Product

Learn More

Legal