Menu
Lenovo SW12041 Manual
              |
Third Edition (December 2017)© Copyright Lenovo 2015, 2017.LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth inContract No. GS-35F-05925.ThinkStation Static Rail Kithttp://www.lenovo.com/support PN: SP40K32881Printed in ChinaImportant information about the ThinkStationStatic Rail KitThis document provides important information about the ThinkStation Static Rail Kit.If you want to install a ThinkStation ® computer into a rack, you need one set of rails. Theset of rails is designed for fixing a 4U ThinkStation computer into a rack without theflexibility of sliding in or out. (“U” is the unit of measurement for defining the vertical spaceused by your ThinkStation computer and 1U is equivalent to 4.445 cm or 1.75 inches.)Your rail kit package contains: One set of rails Two locking clips One stopper Two cage nuts Two bolts DocumentationIf any item is missing or damaged, contact your place of purchase. Ensure that you retainyour proof of purchase and packing material. They might be required to receive warrantyservice.About the rackCAUTION: Be sure to read and understand the documentation that comes with therack for safety and cabling information. Before you install a workstation into therack, also ensure that you read and understand all safety information andguidelines in this document. Reading and understanding the information reducesthe risk of personal injury and damage to your product.The rack must meet one of the following requirements: Standard 4-post (square-hole), 19-inch rack configuration compliant with EIA-310-Eas defined by the Electronic Industries Alliance Standard 4-post (unthreaded round-hole), 19-inch rack configuration compliant withEIA-310-E as defined by the Electronic Industries AllianceThe dimensions of the rack must meet the following requirements:Rear mounting flangeFront mounting flangeRack front doorThe following table explains the dimension requirements of the rack.Item Dimensions DescriptionA 609.6 – 914.4 mm(24 – 36 inches)Item A refers to the distance between the frontmounting flange and the rear mounting flange .The distance must be 609.6 mm (24 inches) inminimum and 914.4 mm (36 inches) in maximum.B > 474 mm(18.66 inches)Item B refers to the internal width of the rail kit. Thewidth must exceed 474 mm (18.66 inches).D > 60 mm(2.36 inches)Item D refers to the distance between the frontmounting flange and the inside of the rack frontdoor . The distance must exceed 60 mm (2.36inches). This clearance is required for the chassis pullhandles on the front of the ThinkStation computer aswell as air circulation through the rack.L > 950 mm(37.4 inches)Item L refers to the distance between the frontmounting flange and the rear of the rack. Thedistance must exceed 950 mm (37.4 inches).Read these guidelines firstBefore you install the ThinkStation computer into a rack, review the following guidelines.The guidelines help you in your installation and avoid the risk of personal injury anddamage to your product.Two or more people are required to lift a ThinkStation computer, move a ThinkStationcomputer, or install a ThinkStation computer into a rack. You also can use a workstationcomputer-lifting tool for help.≥ 18 kg (39.7 lb)< 32 kg (70.5 lb)≥ 32 kg (70.5 lb)< 55 kg (121.2 lb)≥ 55 kg (121.2 lb)< 100 kg (220.5 lb)CAUTIONUse safe practices when lifting. Before installing a ThinkStation computer into a rack, remove all media from thedrives and turn off all attached devices and the ThinkStation computer. Then,disconnect all power cords from electrical outlets and disconnect all cables that areconnected to the ThinkStation computer. Ensure that the room air temperature is below 35°C (95°F). Do not block any air vents; usually 15 cm (6 inches) of space provides proper airflow. Do not leave open spaces above or below an installed ThinkStation computer in yourrack. To help prevent damage to ThinkStation computer components, always install ablank filler panel to cover the open space and to help ensure proper air circulation. Install the ThinkStation computer only in a rack with perforated doors for both securityand proper airflow. Start from the bottom of the rack for the ThinkStation computer or device installation. Install the heaviest ThinkStation computer or device in the bottom of the rack. Do not extend more than one ThinkStation computer or device out of the rack at thesame time. If possible, remove the doors and side panels of the rack to provide easier accessduring installation. Do not overload the electrical outlet when you install multiple devices in the rack. Connect all power cords to proper electrical outlets and properly manage all thecables in the rack. Refer to the documentation that comes with the rack aboutmanaging cables. Do not place any object on top of rack-mounted devices. When you move or ship the rack, remove the ThinkStation computer secured by therail kit from the rack first. Refer to the documentation that comes with the rack and thedocumentation that comes with each rail kit for detailed information.Installing a ThinkStation computer into a rack(with static rail kit)Before you begin, remove all the parts from the rail kit package and lay all the parts on aworking surface. Measure the rack before the installation to ensure that the rack canaccommodate the static rail.Note: The holes in a mounting flange are separated into groups by measuring marks. Thethree holes between two adjacent measuring marks form a group, which indicates 1Uspace. Note the measuring marks on a mounting flange to help you correctly select a rackmounting area for the ThinkStation computer. For more information about the placementof the holes in a mounting flange, refer to the documentation that comes with the rack.To install a ThinkStation computer into a rack, do the following:1. Install the rail kit by doing the following:a. Select a proper rack mounting area for the left static rail. Position the rear end ofthe left rail to the mounting area. Ensure that the tabs on the rear end of the railare aligned with the corresponding holes in the mounting area. Press the latchand push the rail until the rear end of the left static rail is firmly secured to themounting flange.If the holes in a mounting flange are round, the installation method is the same.Press the latch and push the rail until the inner round posts of the tabs areinserted into the corresponding holes. Then, the rear end of the rail is firmlysecured to the mounting flange.b. Position the front end of the left static rail to the mounting flange. Ensure that thefront end and rear end of the left static rail are at the same horizontal level. Pressthe latch and push the rail until the front end of the rail is firmly secured to themounting flange.If the holes in a mounting flange are round, the installation method is the same.Press the latch and push the rail until the inner round posts of the tabs areinserted into the corresponding holes. Then, the front end of the rail is firmlysecured to the mounting flange.c. Repeat steps a through b to install the right static rail to the opposite side of therack.2. Depending on the type of the handles on the front of your computer, install a lockingclip or two cage nuts on the front mounting flange.• For the computer handle with a hole, install a locking clip. Remove the two screwson the side of the locking clip. Install the locking clip on the mounting flangeabove the rail as shown. Then reinstall the two screws to secure the locking clipto the mounting flange.• For the computer handle without a hole, install the two cage nuts on the mountingflange above the rail as shown.3. Remove the four feet on the bottom of the computer.4. Position the computer onto the rails. Then slide the computer to the rear of the rackuntil the hole in the computer handle is aligned with the locking clip.5. Secure the computer to the rack by either of the following:• Press the button on each locking clip.• Press the button on the locking clip . Align the holes in the stopper with theinstalled cage nuts and position the stopper onto the computer handle. Install thetwo bolts to secure the stopper on the mounting flange .Legal noticesLenovo ®, the Lenovo logo, ThinkStation, and the ThinkStation logo are trademarks ofLenovo in the United States, other countries, or both.Other company, product, or service names may be trademarks or service marks of others. |
Related manuals for Lenovo 4XF0K29048
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved