Lantronix SISPM1040-582-LRT Quick Start Manual

Also see for SISPM1040-582-LRT: Quick start guide Install guide Manual

Lantronix SISPM1040-582-LRT Quick Start Manual Manual pdf 1 page image

SISPM1040-582-LRT Quick Start Guide33754 Rev. F https://www.lantronix.com/ Page 1 of 2SISPM1040-582-LRTManaged Hardened PoE++ Switch (8) 10/100/1000Base-T PoE++Ports + (2) 100/1000Base-X SFP SlotQuick Start GuideSee the Install Guide for important Cautions and Warnings, Features,Specs, Back and Front Panel, LEDs, DIP Switch Settings, RESET button,Installation, Mounting, Installing SFPs, Connecting Devices, DI/DO Relay,Grounding, Connecting P1 and P2, Power Supply, Initial Config,Troubleshooting, Warranty, PoE Modes, Compliance, and Tech Support.Warning and Caution - Proper Installation and Operation (English): These devices are open-type devices that are to be installed in anenclosure only accessible with the use of a tool, suitable for the environment. This equipment is suitable for use in Class I, Division 2,Groups A, B, C, and D or non-hazardous locations only. WARNING – EXPLOSION HAZARD. DO NOT DISCONNECT WHILE THE CIRCUIT IS LIVEOR UNLESS THE AREA IS FREE OF IGNITIBLE CONCENTRATIONS.Avertissement et mise en garde - Installation et fonctionnement corrects (français): Ces périphériques sont des périphériques de typeouvert qui doivent être installés dans un enceinte uniquement accessible à l'aide d'un outil, adapté à environnement.Cet équipement peut être utilisé dans la classe I, division 2, groupes A, B, C, et D ou des emplacements non dangereux seulement.AVERTISSEMENT - RISQUE D'EXPLOSION. NE PAS SE DÉCONNECTER LORSQUE LE CIRCUIT EST VIVANT OU À MOINS QUE LA ZONE NE SOITLIBRE DE CONCENTRATIONS IGNIFIABLES.Package Contents: Verify you received one Switch with Terminal Block attached, one DB-9 to RJ-45 Cable, four adhesiverubber feet, this document, and one DIN Rack mount kit.Front Panel: The SISPM1040-582-LRT front panel ports, LEDs, Power Input terminal block, DI/DO terminal block,CONSOLE port, DIP Switch, RESET button, and Ground screw.LED Indicators: The front panel LEDs provide switch and Ring status. Power LEDs indicate if the switch is powered upcorrectly. System LED: indicates if the system is ready or not ready. Alarm LED indicates if the system is normal or not.Ring Master LED and Rapid Chain LED indicate if the Rapid Ring is ready. Port Status LEDs indicate the current status ofeach port. See the Install Guide for details.DIP Switch for Ring Settings: The two-position DIP switch is labeled RC (1) (Rapid Chain) and RM (2) (RingMaster). The DIP switch lets you avoid having to access the Web UI or CLI to configure a ring. See theInstall Guide for DIP switch setting details.RESET Button: To reset the switch press RESET for 2~7 seconds; the SYS LED blinks green; Port status LEDs are Off.To restore to defaults, press RESET for 7~12 seconds; the SYS LED blinks green; Port status LEDs are all ON.Installation: Caution: The switch is an indoor device. If used with outdoor devices such as outdoor IP cameras oroutdoor Wi-Fi APs, then it is strongly suggested to install a surge protector or surge suppressor to protect the switch.Compliant with 802.3at in Environment A when using an isolated power supply. For other apps, see the Install Guide.These devices are open-type devices that are to be installed in an enclosure only accessible with the use of a tool,suitable for the environment. This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D or non-hazardous locations only. “WARNING – EXPLOSION HAZARD. DO NOT DISCONNECT WHILE THE CIRCUIT IS LIVE ORUNLESS THE AREA IS FREE OF IGNITIBLE CONCENTRATIONS. Temperature code (T-Code) – T4.Grounding Screw: CAUTION: Be sure to disconnect the Switch from the power source before installing and wiring thedevice. ATTENTION: This case must be earth grounded. No DC input may be earth grounded. Use Isolated Power Supply.Caution: The switch is intended to be grounded to a well-grounded mounting surface such as a metal plate. Install thegrounding wire prior to connecting any other device to the Switch.Warning: Turn the power off before connecting or disconnecting modules or wires. The correct power supply voltage islisted on the product label. Check the voltage of your power source to make sure that you are using the correct voltage.Do NOT use a voltage greater than what is specified on the product label.

/ 2

Related manuals for Lantronix SISPM1040-582-LRT