Lake LM Series Operation Manual

Also see for LM 26: Specifications Operation manual Quick start guide

Lake LM Series Operation Manual Manual pdf 57 page image

Appendix51Lake LM Series Operation Manual Rev 1.3.5Router 5: EmptyRouter 6: EmptyRouter 7: EmptyRouter 8: Empty8.3.2.2 Router Defaults (LM 44)Router 1: Priority 1 = Dante (Ch.1), Priority 2 = Empty, Priority 3 = AES1 (Ch.1), Priority 4 = Analog 1Router 2: Priority 1 = Dante (Ch.2), Priority 2 = Empty, Priority 3 = AES1 (Ch.2), Priority 4 = Analog 2Router 3: Priority 1 = Dante (Ch.3), Priority 2 = Empty, Priority 3 = AES2 (Ch.3), Priority 4 = Analog 3Router 4: Priority 1 = Dante (Ch.4), Priority 2 = Empty, Priority 3 = AES2 (Ch.4), Priority 4 = Analog 4Router 5: Priority 1 = Empty, Priority 2 = Empty, Priority 3 = AES3 (Ch.5), Priority 4 = EmptyRouter 6: Priority 1 = Empty, Priority 2 = Empty, Priority 3 = AES3 (Ch.6), Priority 4 = EmptyRouter 7: Priority 1 = Empty, Priority 2 = Empty, Priority 3 = AES4 (Ch.7), Priority 4 = EmptyRouter 8: Priority 1 = Empty, Priority 2 = Empty, Priority 3 = AES4 (Ch.8), Priority 4 = Empty8.3.3 Other Device DefaultsDual Redundancy: DisabledDante Slave Only: DisabledGPIO: No Action / No IndicationIP Configuration: Auto Zero Conf. (Auto IP)8.4 Glossary of Terms, Acronyms and AbbreviationsThe explanations given in Table 8-2 below are based on the specific use of each term in this manual. Thedefinitions are not intended to be exhaustive and many of these terms have wider meanings.Term Description100/1000 Base-T 100/1000 Base-T is IT industry-speak for different standards of Ethernet network. This term incorporates 100 Base-TX, which operatesat 100 Mbps, and 1000 Base-T which operates at 1000 Mbps (1 Gbps).Access Point See Wireless Access Point.Auto-Sensing The Ethernet ports automatically determine the base speed of the network they are connected to (10 Base-T or 100 Base-T) andconfigure themselves appropriately. This is termed auto-sensing.Auto-Uplink The Ethernet ports can operate with either straight or crossed network cables. This ability to connect correctly with either type istermed auto-uplinking.Auxiliary Output Some of the configurations possible in the Lake processing system Modules result in a single audio processing channel being created inaddition to a crossover. This is termed an Auxiliary output.Backbone Large Ethernet networks are often implemented with a very high speed “trunk” part of the network topology feeding main switches,which in turn support smaller, lower-speed local networks. The term backbone is used to describe such a trunk.Bandwidth The bandwidth of a signal channel or interconnection is the range of frequencies it is able to handle. The term can be applied to bothaudio channels and Ethernet networks.Cat-5e/Cat-6, etc. Designations of industry-standard cables suitable for Ethernet networks using four twisted pairs of conductors. Often referred to as UTPcable (Unscreened Twisted Pair). Cat-5 has generally been replaced by Cat-5e (e = ‘enhanced’). Either Cat-5e or Cat-6 cable are suitablefor networking Lake and Lab.gruppen devices.Chain An Ethernet network comprising several devices interconnected using the Secondary connectors to daisy-chain the units together is anexample of a network with a chain topology.Clock Digital audio is produced by sampling analog audio at a known, fixed rate, controlled by some form of master clock. Problems can occurwhen interconnecting two pieces of digital audio equipment if their internal master clocks are not synchronized. Various techniques maybe employed to ensure that this is the case.

/ 71

This manual is suitable for:

LM 26 LM 44 LM Series

Lake LM Series Operation Manual

Product

Learn More

Legal