KitchenAid Architect Series II KUDE60FX User Manual

Also see for Architect Series II KUDE60FX: Installation instructions Energy guide

Contents

KitchenAid Architect Series II KUDE60FX User Manual Manual pdf 10 page image

10Dishwasher Feedback SectionControl Lock Avoids unintended use of the dishwasher between cycles, or cycle and option changes during a cycle.To turn on Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. The ControlLock light will stay on for a short time, indicating that it is activated, and all buttons are disabled. If you press any buttonwhile your dishwasher is locked, the light flashes 3 times and an audible tone will sound. The dishwasher door can stillbe opened/closed while the controls are locked.To turn off Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. The lightturns off.NOTE: If your model requires you to press and hold 4 Hour Delay to lock the controls, the Control Locked LED will beon or off to indicate if the Control Lock is active or not.CONTROLS AND CYCLE STATUSCONTROL PURPOSE COMMENTSTo start or resume awash cycleIf the door is opened during a cycle or the power is interrupted, the START/RESUMEindicator flashes. The cycle will not resume until the door is closed and START/RESUME ispressed.NOTE: If the START/RESUME button is located on top of door, push door firmly closedwithin 3 seconds of pressing START/RESUME. If the door is not closed within 3 seconds,the start button LED will flash, an audible tone will be heard, and the cycle will not start.To reset any cycle oroptions duringselection.To cancel a washcycle after it'sstarted.Press CANCEL/DRAIN to reset any control selections made.See “Canceling A Cycle After Dishwasher Is Started” and “Changing a Cycle AfterDishwasher is Started” sections.To turn the audibletones on or off.Press and hold the Hi Temp Scrub button for 3 seconds to turn the audible tones on or off.Only audible tones for confirming button presses can be turned on/off. Important audibletones, such as indicating a cycle has been interrupted, cannot be deactivated.CONTROLS AND CYCLE STATUSCONTROL PURPOSE COMMENTSThe Cycle Status IndicatorLights are used to follow theprogress of the dishwashercycle. Located on the frontof the dishwasher for frontcontrol models, and locatedon the top of the door forhidden control models.Clean indicator glows when a cycle is finished.If you select the Sani Rinse option, when the Sani Rinse cycle is finished,the Sanitized indicator glows. If your dishwasher did not properly sanitizeyour dishes, the light flashes at the end of the cycle. This can happen if thecycle is interrupted, or the water could not be heated to the requiredtemperature.The Clean and Sanitized lights go off when you open and close the door orpress CANCEL.The Front Indicator Light orSingle Exterior Light (A)shows progress of yourdishwasher cycle by color(for hidden control modelsonly).The light will be blue if the dishwasher is washing or rinsing. The light willbe red when the dishwasher is drying. The light will be green to indicatethat the cycle is complete. If the Front Indicator Light is blinking, see“Troubleshooting” section.The Cycle Status Display isused to follow the progressof the dishwasher cycle, andto show other information.(Available on some modelsinstead of Cycle StatusIndicator Lights)The indicators will inform you if you are able to add a dish to the cycle afterit has started. It will also inform you if the dishwasher is washing, rinsing,drying, complete, and/or sanitized. They will show whether the control islocked and/or the delay option is selected. A series of bars will count downthe duration of the cycle remaining from left to right. Each bar equalsapproximately 24 minutes of cycle length. The bars will also count downthe delay feature from left to right, and the delay indicator will be activated.OPTION SELECTIONSOPTIONS CAN BESELECTED WITH WHAT IT DOES ADDED TIME TO CYCLE ADDEDWATERGALLONS(LITERS)TYPICAL MAXorA