Key Digital KD-IP120TX Operating Instructions Manual

Also see for KD-IP120POERX: Guide Manual

Contents

Key Digital KD-IP120TX Operating Instructions Manual Manual pdf 8 page image

12 13For KD-IP120 Tx and Rx› Network Setup is where the IP Addresss, Subnet Mask, and Router IP Address may bechanged when. Click Apply to save changes› Multicast Setup is where the Group ID may be changed and IGMP may be enabled ordisabled. **Please be aware that Group ID’s cannot clash for Tx Units. Each Tx Unitmust have a unique Group ID. Treat Group ID as Source Input Number. Rx Unit GroupID’s are to connect to a Tx to view video from that source**› Main Firmware Upgrade is where the firmware of the unit may be upgraded by file. Rebootmay also be accessed from here.For KD-IP120 Tx Only› Encoder Firmware Upgrade is where the encoder may be upgraded by file. Encoderfeature may be rebooted from here.› EDID Upgrade is where the EDID settings may be changed by file. Update the EDID perspecific Tx source to ensure the optimal video resolution is output by your source.Default EDID file of KD-IP120 units is 1080p with 2ch audio.» Email tech@keydigital.com for additional EDID files.Protocol: RS-232 and TCP/IP CommandsWith the companion of a KD-MC1000 or other Compass Control MC gateways, 3rd partyintegrators may control the switching capabilities of the KD-IP120 system with a few simplecommands.Connection to the KD-IP120 via KD-MC1000 plugged into the same network may be donethrough RS-232 or TCP/IP.For RS-232 control, the only Multi-Function I/O port that supports a RS-232 connectionfor KD-IP120 control is the Zigbee RS-232 I/O port on the rear of the KD-MC1000, modelKD-3.5MDB964C.The KD-MC1000 comes with a special 3.5 to RS-232 cable that has3 rings, 4 conductors. This is the only cable that may be used in the Zigbee RS-232 I/O port.›Pin 5 – GroundPin 3 – ReceivePin 2 – TransmitRS-232 cable pin outRS-232 Protocol:» Baud Rate = 57600 bits per second» Data Bits = 8» Stop Bits = 1» Parity = None» Flow Control = None» Carriage Return: Required» Line Feed: Required› Commands are not case-sensitive. Spaces shown below may be excluded.› Carriage return and line feed is required at the end of each string.For TCP/IP control, make sure the TCP/IP client is on the same network as the KD-MC1000 and the KD-IP120. The port for control is telnet (23).Commands:SPO xxxx SI yyyy Switches the desired Video Input to the desired Outputxxxx = the Output number [0000 to 9999] –or– [A] for allValue for xxxx/yyyy may range from 2 to 4 characters long (xx to xxxx).yyyy = the Input number [00 to 1024] –or– [U, D] for “Up” and “Down”respectively[U, D] will increase/decrease the input number from its current positionThis command will switch Inputs to your desired OutputExample: To switch Output 8 to Input 4, issue the command:SPO08SI04Example: To increment the Input Up on Output 14, issue the command:SPO14SIUExample: To switch All Outputs to Input 9, issue the command:SPOASI09STA Gets Status of KD-IP120 SystemSTPI xxxx Gets Video Status of Tx Inputxxxx = the Input number [00 to 1024]STPO xxxx Gets Video Status of Rx Inputxxxx = the Output number [0000 to 9999]SPCDF Reset All to Factory DefaultSpecificationsTechnical:» Inputs (each): 1 HDMI connector, Type A, 19 pin female; 1 HD» Outputs (each): 2 HDMI connectors, Type A, 19 pin female;» TMDS Bandwidth: 2.25 Gb/s per Channel» Deep Color Support: Supports digital video formats in Deep Color Mode up to 12 bits/color with all HDMI and HDCP technologies» Link: Single Link» DDC Signal (Data): Input DDC signal – 5 Volts p-p (TTL)» HDMI Video/Audio Signal: 1.2 Volts p-p» DDC Communication: EDID and HDCP buffering between source and display» Power: KD-PS5V2ASC, 5V/2A, 100-240VAC, 50-60Hz, Interchangeable head,screw-in connectorKD-IP120_Manual.indd 12-13 5/3/16 4:53 PM

/ 10

Related manuals for Key Digital KD-IP120POERX