Kelvinator KWH20CRC User Manual

Also see for KWH20CRC: User manual

Contents

Kelvinator KWH20CRC User Manual Manual pdf 10 page image

10 installation instructions Kelvinator Air ConditioningNote: unit may be supported by asolid frame from below orby a hanger from a solidoverhead support.Preferred method of installation into a timberframed wall, partition or window.Flash or seal around externalWall frame or architraveFlash or seal around externalWall frame or architraveEnsure louvresare entirelyoutside the wallDrain panSteadying bracket(one per side)Solid timber supportStudy timberframeTimber framewall or partitionSturdy timberframe allround unitTimber framedWall or partitionDrain panExternal supportframe at balancepoint of A/CAlternately, bracketsas illustrated belowmay be used.Alternative method of installation if external45° brick cut awayto clear louvresFrontLouvresupport cannot be provided.AIR INAIR OUT100mm minimumAIR INOPTION A OPTION BAIR OUT100mmAIR IN TOPVIEWBR ICKWALLAIR INflash or seal around externalwall frame of architravesturdy timberframe allaround unittimber framedwall or partitionexternal support frameat balance point of A/Calternately, brackets asillustrated below maybe usedpreferred method of installation into a timberframed wall, partition or windowdrainInstallation of the unit into the housing1 Slide the unit into the housing until it is firmly against therear of the housing. Care is required to ensure the foamsealing strips on the housing remain in position.2 Connect the air conditioner to the power and positionexcess cord length beneath the air conditioner base.3 Engage the chassis fixing brackets into the bottomhousing rail and secure to the base with thescrews provided.4 Remove the front panel from it's carton and plastic bagand fit as per the Installation lnstruction.5 Switch unit on. Check for operation of the unit and checkfor vibration in the installation.6 Fit the drain pan to the housing and run a drain line to asuitable location if required.Installing the unit into the wallNote: unit may be supported by asolid frame from below orby a hanger from a solidoverhead support.Preferred method of installation into a timbeframed wall, partition or window.Flash or seal around externalWall frame or architraveFlash or seal around externalWall frame or architraveEnsure lare entiroutsideDrain pSteadying bracket(one per side)Solid timber supportStudy timberframeTimber framewall or partitionSturdy timberframe allround unitTimber framedWall or partitionDrainExternal supportframe at balancepoint of A/CAlternately, brackeas illustrated belowmay be used.Alternative method of installation if ext45° brickto clear losupport cannot be provided.AIR INAIR OUT100mm minimumAIR INOPTION AABRWAAIR INair inair inair out100mm minimumoption Aair inNote: unit may be supported by asolid frame from below orby a hanger from a solidoverhead support.Preferred method of installation into a timberframed wall, partition or window.Flash or seal around externalWall frame or architraveFlash or seal around externalWall frame or architraveEnsure louvresare entirelyoutside the wallDrain panSteadying bracket(one per side)Solid timber supportStudy timberframeTimber framewall or partitionSturdy timberframe allround unitTimber framedWall or partitionDrain panExternal supportframe at balancepoint of A/CAlternately, bracketsas illustrated belowmay be used.Alternative method of installation if external45° brick cut awayto clear louvres 45° brick cut awayto clear louvresFrontLouvresupport cannot be provided.AIR INAIR OUT100mm minimumAIR INOPTION A OPTION BBR ICKWALLAIR OUTA100mm100mmIR INAIR IN TOPVIEWBR ICKWALLAIR INair outair inair inlouvre100mm100mmfront45° brick cut awayto clear louvres45° brick cut awayto clear louvresoption BSelect the best location1 To avoid vibration and noise, make sure the unit isinstalled securely and firmly.2 Install the unit where the sunlight does not shine directlyon the unit.If the unit receives direct sunlight, build an awning toshade the cabinet.3 There should be no obstacle, such as a fence or wall,within 50cm from the back of the cabinet because it willprevent heat radiation of the condensor.Restriction of outside air will greatly reduce the coolingand heating efficiency of the air conditioner.4 Install the unit a little obliquely outward not to leak thecondensed water into the room (about 10mm or 1/4bubble with level).5 Install the unit with its bottom portion 75~150cm abovethe floor level.6 The power cord must be connected to an independentcircuit. The yellow/green wire must be grounded.7 Based on calculations in compliance with AS60335.2.40there is no minimum safe floor area for the installation ofthe air conditioners described in this manual.cautionAll side louvers of the cabinet must remain exposed to theoutside of the structure.less than 220mmmore than 160mmwall thickness is less than 220mmmake rear of the airconditioner (outside)lower than the front of the airconditioner(inside) to allow water to drain5-10mmInstallation of the Housing1 Remove the air conditioner from its packaging, removefixing screws and slide the air conditioner out of itshousing (Refer to Installation Steps).2 Prepare the hole in the wall so that the bottom ofthe housing is well supported, the top has minimumclearance and the air inlet louvers have clearance asshown below in options A and B. Holes from the outsidethrough to the cavity should be sealed. The housingshould slope down towards the rear by about 5mm toallow water formed during operation to drain.3 Install the housing into the wall and secure. Ensure thefoam seals are not damaged. Flash, seal or fill gapsaround the inside and outside to provide satisfactoryappearance and protection against the weather, insectsand rodents.Note: Unit may be supported by a solid frame from below orby a hanger from a solid overhead support.Installation instructions