Model 2001 MultimeterQuick Reference Guide

Safety Precautions

Introduction

Operation Summary

Multiple Displays

Menu Structures

Default Conditions

Error and Status Messages

IEEE-488.2 Common Commands and Queries

SCPI Command Subsystems

Keithley 2001 Quick Reference Manual

2001

safety precautions

Manual addenda

Front and rear panel summary

getting started

Front panel display

Overview of measurement process

Idle

Initial configuration

Storing DC voltage readings example

IEEE-488.2 and SCPI basics

Syntax rules

Programming examples

Power-up procedure

Line fuse replacement

High energy circuit safety precautions

Power-on default conditions

Multiple displays

Information messages

Menu structures

Functions

DC and AC voltage

DC and AC current

Two and four-wire resistance

Frequency

Temperature

Range

Autoranging

Enabling rel

Configuring the measure layer

Configuring the scan layer

Configuring the arm layer

Halting triggers

Trigger Link

Buffer

Burst mode

Configuring data storage

Storing and recalling readings

Buffer multiple displays

Filters

digital filter

filter

Math

Percent

Scanning

channels

examples

SAVESETUP

GPIB

CALIBRATION

TEST

STATUS-MSG

Primary address selection

Status structure

Operation event status

Arm event status

Sequence event status

Trigger event status

Measurement event status

Questionable event status

Queues

Status byte and service request (SRQ)

Trigger Model (IEEE-488 operation)

scan layer

General bus commands

REN (remote enable)

GTL (go to local) and local

Programming syntax

Program messages

Response messages

Message exchange protocol

Common commands

CLS - clear status

ESE? - event enable query

IDN? - identification query

OPC? - operation complete query

OPT? - option identification query

RCL - recall

SRE - service request enable

SRE? - service request enable query

STB? - status byte query

TRG - trigger

TST? - self-test query

Signal oriented measurement commands

SCPI command subsystems

Calculate subsystems

CALCulate[1]

CALCulate2

CALCulate3

CALibration subsystem

DISPlay subsystem

performance verification

restoring default conditions

verification procedures

dc current verification

ac current verification

resistance verification

frequency accuracy verification

temperature reading checks

line power

required order of command execution

calibration errors

ieee-488 bus error reporting

ieee-488 bus comprehensive calibration

ac self-calibration

low-level calibration summary

front panel low-level calibration procedure

calibration:protected subsystem

calibration:unprotected subsystem

detecting calibration step completion

using the *opc command

frequency counter

general program instructions

Warranty information

Figure 2-1 Model 2001 front panel

Figure 2-2 Model 2001 rear panel

Table 2-1 DCV multiple displays

Front panel operation

Figure 2-4 Typical DC voltage connections

Table 2-3 CONFIGURE DCV menu structure

Table 2-4 Multiple displays for recalled readings

Abbreviated SCPI command summary

Table 2-7 Abbreviated SCPI command summary

Table 3-1 Data checked on power-up

Figure 3-1 Model 2001 display formats

Table 3-3 Multiple displays by function

Figure 3-3 Bar graph (zero-at-left) multiple display

Table 3-4 Status and error messages

Figure 3-6 DC voltage measurements

Table 3-6 CONFIGURE DCV menu structure

Table 3-7 CONFIGURE ACV menu structure

Table 3-8 DCV and ACV integration times set-by-resolution

Table 3-10 DCV and ACV auto resolution

Figure 3-8 Positive and negative peak spikes

Figure 3-9 DC voltage multifunction multiple displays

Figure 3-10 AC voltage multifunction multiple displays

Figure 3-11 DC and AC current measurements

Table 3-11 CONFIGURE DCI menu structure

Table 3-12 CONFIGURE ACI menu structure

Table 3-15 DCI and ACI auto resolution

Figure 3-12 DC in-circuit current measurements

Figure 3-14 Two-wire resistance measurements

Figure 3-15 Four-wire resistance measurements

Table 3-17 CONFIGURE OHMS-4W menu structure

Table 3-20 Ω 2 and Ω 4 auto resolution

Figure 3-16 Frequency measurements

Table 3-22 CONFIGURE FREQUENCY menu structure

Figure 3-17 4-wire RTD temperature measurements

Figure 3-18 3-wire RTD temperature measurements

Table 3-23 CONFIG TEMPERATURE menu structure

Figure 3-21 Temperature equations

Table 3-25 Temperature integration time set-by-resolution

Table 3-26 Temperature auto resolution

Table 3-28 CONFIGURE TRIGGER menu structure

Figure 3-22 Trigger model (front panel operation)

Figure 3-27 External trigger connectors

Figure 3-29 DUT test system

Figure 3-31 Operation model for asynchronous trigger link example #1

Figure 3-32 Connections using Trigger Link adapter

Figure 3-34 Trigger Link connections (asynchronous example #2)

Figure 3-35 Operation model for asynchronous Trigger Link example #2

Figure 3-37 Typical semi-synchronous mode connections

Figure 3-38 Trigger Link connections (semi-synchronous example)

Figure 3-39 Operation mode for semi-synchronous Trigger Link example

Available functions in burst mode

Burst mode sequence

CONFIG-FILTER menu structure

Enabling math

Keithley 2001 Quick Reference Manual

Product

Learn More

Legal


Contents Table Of Contents Safety Precautions Introduction Operation Summary Multiple Displays Menu Structures Default Conditions Error and Status Messages IEEE-488.2 Common Commands and Queries SCPI Command Subsystems	Model 2001 MultimeterQuick Reference Guide Next / 94