OneStart

Menu

Kaden KU5 Installer Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Warnings and Important Information
  4. General Guidelines
  5. Gas Inlet Connection
  6. Heater Positioning
  7. Installation of Internal Heaters - Room, Enclosure or Plant Room
  8. KU Universal Model Guidelines
  9. Return & Supply Air POP Rotation Procedure
  10. Internal Model Flueing Instructions
  11. External Installation
  12. Installation of Flue Terminal
  13. Installation of Flashing
  14. Thermistor Installation KU4 & KU5
  15. KU4 & KU5 - Adaptive Zoning & Add-On AC
  16. KE External Model Guidelines
  17. Installation
  19. Fan Speed Setting For KU3, KE3 & KE4 Models
  20. Ducting Information
  21. Outlet Guide
  22. Outlet Register Chart
  23. Wall Control Installation
  24. Programmable Wall Control Installation
  25. Wiring the Programmable Wall Control to a KE4 Heater
  26. Wiring the Manual Wall Control to a KE3 Heater
  27. Commissioning KU4 & KU5
  28. Installer Parameters Control LCD Settings
  29. KU4 & KU5 Commissioning Instructions
  30. Final Checks
  31. Commissioning KU3, KE3 & KE4
  32. Setting the fan speed
  33. Technical Specifications
  34. Technical Support
Kaden KU5 Installer Manual Manual pdf 14 page image
14Kaden Installer's ManualDucted Gas Heaters2.4 EXTERNAL INSTALLATION2.4.1 Supply Air Overheat Switch Position (KU530 & KU330 ONLY)For external installations of the KU530 (refer to Diagram 5) and KU330 (refer to Diagram 6) heaters the supply airoverheat switch position must be changed from end discharge to side discharge modify as follows:2.4.1.1 KU5301. Disconnect the quick connect terminals (Orange / White) for the overheat switch loom connected from theend discharge overheat switch behind the burners.2. Reconnect the quick connect terminals (Orange / White) to the side discharge overheat switch. Theseterminals can be identified by the label "SIDE DISCHARGE O/H SWITCH".Flue TerminalConnectionKU530 End Discaharge O/H Switchquick connect terminals(factory default connection)Side Discharge O/H Switchquick connect terminals12O/H Switch LoomDiagram 52.4.1.2 KU3301. Disconnect the quick connect terminals (Orange / White) for the overheat switch loom connected to the enddischarge overheat switch behind the burners.2. The KU330 is fitted with both left and right side discharge O/H Switches, reconnect the quick connectterminals (Orange / White) to the O/H Switch on the same side the air is supplied from. These terminals canbe identified by labels on the sheet metal plate above the burner "LEFT SIDE DISCHARGE O/H SWITCH"or "RIGHT SIDE DISCHARGE O/H SWITCH".Flue TerminalConnectionKU330 Left Side Discharge O/HSwitch quick connect terminals122LREnd Discaharge O/H Switchquick connect terminals (factorydefault connection)O/H Switch LoomRight Side Discharge O/HSwitch quick connect terminalsDiagram 62.4.2 Modifying KU Model Duct OrientationThe duct orientation of KU series heaters can be reversed if the installation requires it. For more information referto "2.3.3 Return & Supply Air POP Rotation Procedure" on page 12.
/ 40
This manual is suitable for:
KE3KE4KU3KU4KU5
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved