JVC RX-7030VBK Instructions Manual

Also see for RX-7032VSL: Instructions Instructions Instructions Instructions Instruction manual

Contents

i_j _ ']/'_ [.]11_1 [']iiYou can enjoy the sound closer lo the original source by oven'idingthe sound adjustments such as speaker output level adjustments (seepage 32), Digital Equalization (see page 32), Surround and DSPmodes (see pages 34 to 39), Bass Boost (see page 22) and MidnightMode (see page 20). You can only adjust the volume level whileAnalog Direct is in use.• Once you have made adjustment, it is memorized for each analogsource.L=====JII_©° o_====2Press ANALOG DIRECT so that "A DIRECT" appears on thedisplay.The lamp on the button also lights up.• Each time you press the button, Analog Direct turns on and off.Notes:• Whendigitalinputmodeisinuse, AnafogDirectisnotavailable.• Turning on Surround or DSP mode cancels Analog Direct andpreviously selected sound adjustments are recalled.• If Analog Direct is in use, Midnight Mode is temporarily canceled,• Turning on Analog Direct cancels Input Attenuator (page 20) (andCC Converter for RX-803OVBK: below).I _v_t_ _'_ l _ L'_II__"_!IT_ IJVC's CC (Compensalive Compression) Converter eliminates jilterand ripples, achieving a drastic reduction in digital distortion byprocessing the digital music data in 24 bit-quantization and byexpanding the sampling frequency to 128 kHz (for fs 32 kHzsignals)/176.4 kHz (for fs 44.1 kHz signals)!192 kHz (for fs 48 kHzsignals)+By using CC Converter, you can obtain a nalural sound field fromboth digital and analog sources.When you have connected an MD recorder to the TAPE/MD jacksor a DBS tuner to the TV SOUND/DBS jacks on lhe rear panel,change the source name which will be shown on the display.c:::zc:::zc:::3©L=====JI==...... I°0°L====JWhen changing the source name from "TV" to "DBS":1. Press TV SOUND/I)BS.• Make sure "TV" appeal's on the display.2. Press and hold TV SOUND/DBS until "ASSGN DBS"appears on the display._u_oa[] []H." -':, "3 i.:i i"i i..: ,--:,"3 vo_ 2 5Note:When connecting a DBS tuner to the TV SOUND/DBS IN jacks,change the source name to +DBS," which will be shown on the displaywhen selected as the source. Otherwise you cannot view any picturefrom DBS tune_['or RX-803OVBK:When changing the source name from "TAPE" to "MD":1. Press TAPED.• Make sure "TAPE" appears on the display.2. Press and hold TAPE/MD until ASSGN MD appears onthe display.For RX- 7030 VBK/RX- 7032 VSL:When changing the source name from "TAPE" to "CDR":1. Press TAPE/CDR.• Make sure "TAPE" appears on the display.2. Press and hold TAPE/CDR until "ASSGN CDR" appears onthe display.L====J _====JPress CC CONVERTER so that the lamp on the button lightsup.• Each time you press the button, CC Converter turns on and off(thelamp goes oft') alternately.Note:You cannot use this function while Analog Direct is in use. If you turnon Analog Direct while this function is in use, this function will becanceled.To change the source name to TV and TAPE, repeat Ihesame procedure above.Note:Without changing the source name, you can still use theconnectedcomponents, However, there may be some inconvenience.• For RX.803OVBK:- "TAPE"or "TV" will appear on the display when you select the MDrecorder or DBS tune_- You cannot use the digital input (see pages 19 and 20) for theMD recorder.- You cannot use the COMPU LINK remote control system (seepages 41) to operate the MD recorder.• ForRX.TO3OVBK/RX-7032VSL:- "TAPE"or "TV" will appear on the display when you select the CDrecorder or DBS tune_- You cannot use the digital input (see pages 19 and 20) for theCD recorde_21