JVC RA-P10J Instructions Manual

Also see for RA-P10: Instructions Instructions

PORTABLE AUDIO SYSTEMRA-P10LVT1634-001B [J] ©2006 Victor Company of Japan, Limited 0906NSMCREBETWarnings, Cautions and Others / Mises en garde, précautions et indications diverses(For U.S.A)CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).NO USER SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.RISK OF ELECTRIC SHOCKDO NOT OPENThe lightning flash with arrowhead symbol,within an equilateral triangle is intended toalert the user to the presence of uninsulated"dangerous voltage" within the product'senclosure that may be of sufficientmagnitude to constitute a risk of electricshock to persons.The exclamation point within an equilateraltriangle is intended to alert the user to thepresence of important operating andmaintenance (servicing) instructions in theliterature accompanying the appliance.CAUTION(For U.S.A)WARNING: TO REDUCE THE RISK OF FIREOR ELECTRIC SHOCK, DO NOT EXPOSETHIS APPLIANCE TO RAIN OR MOISTURE.• Rating label is placed on the exterior of the bottom.(For U.S.A)This equipment has been tested and found to complywith the limits for a Class B digital device, pursuantto part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection againstharmful interference in a residential installation.This equipment generates, uses and can radiateradio frequency energy and, if not installed andused in accordance with the instructions, may causeharmful interference to radio communications.However, there is no guarantee that interference willnot occur in a particular installation. If this equipmentdoes cause harmful interference to radio or televisionreception, which can be determined by turning theequipment off and on, the user is encouraged totry to correct the interference by one or more of thefollowing measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment andreceiver.Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.Consult the dealer or an experienced radio/TVtechnician for help.(For U.S.A)CAUTIONChanges or modifications not approved by JVCcould void the user’s authority to operate theequipment.For Canada/pour le CanadaTHIS DIGITAL APPARATUS DOES NOTEXCEED THE CLASS B LIMITS FORRADIO NOISE EMISSIONS FROM DIGITALAPPARATUS AS SET OUT IN THEINTERFERENCE-CAUSING EQUIPMENTSTANDARD ENTITLED “DIGITAL APPARATUS,”ICES-003 OF THE DEPARTMENT OFCOMMUNICATIONS.CET APPAREIL NUMERIQUE RESPECTE LESLIMITES DE BRUITS RADIOELECTRIQUESAPPLICABLES AUX APPAREILS NUMIRIQUESDE CLASSE B PRESCRITES DANS LA NORMESUR LE MATERIEL BROUILLEUR; “APPAREILSNUMERIQUES”, NMB-003 EDICTEE PAR LEMINISTRE DES COMMUNICATIONS.Precautions• Install in a place which is level, dry and neither toohot nor too cold–between 5°C and 35°C (41°F and95°F).• Install the System in a location with adequateventilation to prevent internal heat buildup insidethe System.• Leave sufficient distance between the System andthe TV.• Keep the speakers away from the TV to avoidinterference with TV.Caution: Proper VentilationTo avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:Front: No obstructions and open spacing.Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a standwith a height of 10 cm (3- 15 /16") or more.Attention: Aeration correctePour prevenir tout risque de decharge electrique ou d’incendie et eviter toute deterioration, installez l’appareil de la maniere suivante:Avant: Bien degage de tout objet.Cotes/dessus/dessous: Assurez-vous que rien ne bloque les espaces indiques sur le schema ci-dessous.Dessous: Posez l’appareil sur une surface plane et horizontale. Veillez a ce que sa ventilation correctepuisse se faire en le placant sur un support d’au moins dix centimetres de hauteur.15cm15cm15cm15cm 15cm10cm(5- 15/ 16")(5-15/ 16") (5- 15/ 16")(3- 15/ 16")(5- 15/ 16")(5- 15/ 16")FrontFaceSideCôtéGetting StartedWarning• Store the battery in a place where children cannot reach. If a child accidentally swallows the battery,consult a doctor immediately.• Do not recharge, short, disassemble or heat the battery or dispose of it in a fire. Doing any of these thingsmay cause the battery to give off heat, crack, or start a fire.• Do not leave the battery with other metallic materials. Doing this may cause the battery to give off heat,crack, or start a fire.• When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may start togive off heat, crack, or start a fire.• Do not poke the battery with tweezers or similar tools. Doing this may cause the battery to give off heat,crack, or start a fire.• Dispose of battery in the proper manner, according to federal, state, and local regulations.• The batteries (battery pack or batteries installed ) shall not be exposed to excessive heat source such assunshine, fire or the like.For USA-California OnlyThis product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handlingamay apply.See www.dtsc.ca.gov/hazardouswaste/perchlorateOperating on the Remote ControlQ Supplied AccessoriesAfter unpacking, check to be surethat you have all the following items.• Remote control• AC adaptor• Attachments (6 types)• Rubber pads (A type×2, B type×2)• CR2025 (×2) lithium coin batteriesOne is loaded on the remotecontrol at the factory.Q Prepare the RemoteControl• When you use the remotecontrol for the first time, pullout the insulation sheet.Replacing the Batteryin the Remote Control• Insert the battery into theremote control by matchingthe polarity (+ and –)correctly.Insulation sheetLithiumcoin battery(CR2025)Q Preparation of the Unit9V 1.5A Loading batteries for the ClockBe sure to match the poles (+/-) correctly.Lithium coinbattery(CR2025)(supplied)FM wire antenna(Pass through the notch in the cover)9V 1.5AAC adaptor: AA-R9028 (supplied)To a wall outletPlug the AC adaptoronly after all connectionsare completed.1 SOURCE buttonSwitch the sound source.2 FM MODE buttonSwitch FM stereo/monaural.3 MUTING buttonTurn off the sound. Return to original mode bypressing again.4 PRESET +/- buttonSelect a registered FM radio station (P01 to 20).5 iPod 6 buttonPlay/pause the iPod.6 buttonSwitch the backlight on/off.7 4/¢ buttonFast-forward/rewind the iPod song.Change frequencies to tune in to FM radiostation.8 VOLUME +/- buttonYou can adjust the volume level from 00 to amaximum of 20.TroubleshootingIf you are having a problem with your System, check this list for a possible solution before calling for service.In These Cases Check the following pointsPower does not come on. • AC adaptor is not inserted securely. Plug in securely.• The batteries are exhausted.No longer works. Press the “RESET” button (see “Resetting the unit”).Cannot set the iPod. • Is the selected attachment compatible to your iPod? Confirm thecompatibility of iPod and attachments in “iPod Compatibility Chart”.• Is the attachment properly mounted on the unit? Make sure to mount theattachment properly.Cannot operate iPod. • Is the iPod firmly connected to the connector plug of the unit?• Is the iPod properly functioning? Test the iPod functions in stand alonecondition.iPod cannot be charged. • Is the iPod firmly connected to the connector plug of the unit?• Is the AC adaptor connected? The iPod cannot be charged while the Unitis operated on batteries.• For iPod 3rd Generation, set the “CHARGING SWITCH” to “FIREWIRE”(see “Charging the iPod”).Hard to listen to broadcastsbecause of noise.The FM antenna is not properly extended and positioned.Unable to operate the Systemfrom the remote control.• The path between the remote control and the remote sensor on theSystem is blocked.• The batteries are exhausted.When the volume level ismanually set higher than “08”,the unit automatically lowersthe level to “08”.The unit’s battery runs low (The “---” (Low battery) appears on the display).Replace the batteries with new ones.Q Resetting the unitIf “Troubleshooting” does not eliminate malfunctioning (failure to operate ordisplay properly, etc.), press the “RESET” button on the rear of the unit withsomething having a sharp point, while the unit is turned on. After pressing“RESET” button, unplug the AC adaptor and wait a while before plugging itagain.• When using “RESET” button, make sure the lithium coin battery is loaded.• While resetting the unit, the clock is also reset. Adjust the clock after resettingthe unit.SpecificationsModel RA-P10Type Portable audio systemAmplifier Power Output 4W x 21kHz 10% THD, 6ΩInput Sensitivity/ Impedance AUX Input 250mV/47kΩFM TunerTuning Range 87.5MHz - 108.0MHzFrequency Step 100kHzPreset Stations 20Speaker 1way full range, diameter 35mm x2Input Terminal External DC IN ( for AC adaptor)AUX IN (mini jack)Power SourceDC9V 1.5A (EXTERNAL DC IN)DC9V (SIZE R6, AA BATTERY OR EQUIVALENT x6)DC3V (CR2025, for the clock)AC adaptor Input : AC 110-240V , 50/60HzOutput : DC 9V 1.5ADimensions (W x H x D) (W) 331 mm x (H) 71 mm x (D) 98 mm (13- 1/16" x 2- 13/16" x 3- 7/8")Weight (Without batteries) 0.7kg (1.6 lbs)Accessory See Supplied AccessoriesSpecifications and appearance are subject to change without prior notice.12345678INSTRUCTIONSENOpen the battery compartmentcover by pressing the small tab. Loading batteries for the Unit (The battery power supply)Close the cover in the order shown by the numbers.R6 (SUM-3)/AA (15F) (not supplied)CAUTION:Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type. Connecting the AC adaptorInsert three batteries to each compartment (six batteries total). Be sure to match the poles (+/-) correctly.While the AC adaptor is connected to the wall outlet, the unit works without batteries.Press the tab to openthe cover.Close the cover in the ordershown by the numbers.CAUTION:To avoid risk of fire, and to prevent damage.• Do not use AC adaptors except for the supplied AC adaptor.• Do not use the supplied AC adaptor for other equipment.(Front side)(Rear side)NOTES• Point the remote control at the remote control sensor on the front panel.• The remote control sensor is designed to receive signals from up toapproximately 7 m distance when the remote control is pointed directly. If theremote control is pointed with an angle, the distance may become shorter.DO NOT install the System in a locationnear heat sources, or in a place subject todirect sunlight, excessive dust or vibration.For Customer Use:Enter below the Model No. and Serial No.which are located either on the rear, bot-tom or side of the cabinet. Retain thisinformation for future reference.Model No.Serial No.

/ 2

Related manuals for JVC RA-P10