JVC LVT0858-001A Instructions Manual

Also see for RX-E111RSL: Service manual Service manual Instructions Instructions

Contents

15Basic Settings1 Press SETTING.The CONTROL buttons now work for basicsettings.2 Press CONTROL ∞ (or 5) repeatedly until oneof the following speakers (with the currentsetting)* appears.FRNT SP (Front Speaker) : To register the front speaker size.CNTR SP (Center Speaker): To register the center speaker size.REAR SP (Rear Speaker) : To register the rear speaker size.* “SML (small)” is the initial setting. If you have alreadychanged the setting, another size will be shown.3 Press CONTROL 3 (or 2) to select theappropriate speaker size.• Each time you press the button, the speaker size changes asfollows:LRG (Large) : Select this when the speaker size is relativelylarge. (See “Notes” below.)SML (Small) : Select this when the speaker size is relativelysmall. (See “Notes” below.)NO : Select this when you have not connected aspeaker. (Not selectable for the front speakers.)4 Repeat steps2 and3 to select the appropriatesize for the other speakers.Notes:• Use the following criteria as reference when adjusting:– If the size of the cone speaker unit built in your speaker is greaterthan 12 cm, select “LRG (large),” and if it is smaller than 12 cm,select “SML (small).”• If you have selected “NO” for the subwoofer, you can only select“LRG (large)” for the front speaker size.• If you have selected “SML (small)” for the front speaker size, youcannot select “LRG (large)” for the center and rear speaker sizes.SETTINGANALOG PR ΙΙSUBWFR LFEVOLAUTO SRINPUT ATTDSPL C RLS S RSLPCMDOLBY DDTSCONTROLANALOG PR ΙΙSUBWFR LFEVOLAUTO SRINPUT ATTDSPL C RLS S RSLPCMDOLBY DDTSCONTROLEx.: When registering the rear speaker size.“YES” for the subwoofer and “SML” for the front, center andrear speakers are initial settings. To get best possible sound,change the subwoofer and speaker settings to fit your listeningconditions.Setting the Subwoofer InformationRegister whether you have connected a subwoofer or not. If youhave already connected a subwoofer, follow the procedure below.Before you start, remember...There is a time limit in doing the following steps. If the setting iscanceled before you finish, start from step1 again.1 Press SETTING.The CONTROL buttons now work for basicsettings.2 Press CONTROL ∞ (or 5) repeatedly until“SUBWFR (Subwoofer)” (with the currentsetting)* appears on the display.* “YES” is the initial setting. If you have already changed thesetting, “NO” will be shown.3 Press CONTROL 3 (or 2) to select “YES.”• Each time you press the button, the subwoofer settingalternates between “YES” and “NO.”YES : Select this when you have connected a subwoofer.The subwoofer speaker indicator ( SUBWFR ) lightsup on the display (see page 11). You can adjust thesubwoofer output level (see page 22).NO : Select this when you have not connected or havedisconnected a subwoofer.RemoteNOTSETTINGCONTROLR ΙΙVOLSRATTANALOG PR ΙΙSUBWFR LFEVOLAUTO SRINPUT ATTDSPL C RLS S RSLPCMDOLBY DDTSCONTROLSetting the SpeakersInformationTo obtain the best possible effect from the Surround modes (seepage 32), register the following information after all connections arecompleted.• Speaker Size—FRNT SP, CNTR SP, REAR SP• Speaker Distance—FRNT D, CNTR D, REAR D• Crossover Frequency—CROSS• Low Frequency Effect Attenuator—LFE• Dynamic Range Compression—D.COMPSpeaker Size—FRNT SP, CNTR SP, REAR SPRegister the sizes of all the connected speakers.• When you change your speakers, register the information aboutthe speakers again.Before you start, remember...There is a time limit in doing the following steps. If the setting iscanceled before you finish, start from step1 again.RemoteNOT