JVC LT-32C650 Quick Start Manual

Also see for LT-32C650: Quick start guide Quick start guide Instruction manual

• Do not connect the TV to the mains supply until you have completed all the connections.• Always disconnect the TV from the mains socket when not in use for a long period of time.• The button on the remote control is only used for switching the TV into standby, it does not disconnect the TV from the mains power.To completely disconnect the mains power, please remove the mains plug from the mains socket.Please inspect your TV for damage after unpacking. If you do notice any damage please consult your dealer.Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations.TVTV StandScrews x 4Remote Control/AAA Batteries x2YPbPr CableFAV CableInstruction ManualQuick Start GuideUnpacking11. Connect one end of the RF coaxial cable to the aerial socket on the walland the other end of the cable to the ANT socket on the back of yourTV.2. Plug the TV into a mains socket and switch on at the mains.3. In standby mode, press the button on the remote control to turn theTV on. The LED indicator will flash for a few seconds then the TV willswitch on.Connecting the Aerial and Turning on the TV41. Slide open the battery compartment on the back of the remote control.Operating Your Remote Control2Thank you for purchasing your new JVC TV.Your new TV incorporates the latest technology to enhance yourviewing experience. We would suggest that you allow about 20 minsfor initial setup.Please follow this guide for a successful first time installation.The latest eco-friendly power-saving technology will switch offthe TV if it is left on and idle for 4 hours. Please refer to “AutoStandby” under the “Time Settings” section of the instructionmanual for more detail.Quick Start Guide32" LEDSmart HD TVLT-32C650SCARTSPDIFCoax.OUTVGAANT.HDMI 1(ARC)HDMI 2LANSCARTSPDIFCoax.OUTVGAANT.HDMI 1(ARC)HDMI 2LANRF coaxial cable(not included)2. Insert two AAA size batteries. Make sure to match the (+) and ( - )ends of the batteries with the (+) and ( - ) ends indicated in the batterycompartment.3. Slide the battery compartment cover back into place. Make sure it clicksinto place.OptionalIf you want to connect to the internet via a wired connectionthen connect your ethernet cable to the LAN socket.Need More Help!If you need help setting up your TV then please call:UK: 0344 561 1234Ireland: 1890 818 575Lines are open 24/7The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object,or anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time becausethe screen could crack.Fitting the Stand to the TV3. Ensure the TV is switched off and not connected to the mains power supply.4. Lay the TV down on a flat surface ideally on the edge of a table so the base of theTV slightly overhangs the edge of the table, with the back side facing up. Pleasemake sure a soft cushioned material (such as a dry bath towel or thick piece offoam) is placed beneath the screen.5. Slide the stand under the lip, the neck will fit snugly over the screw holes. Thenscrew the stand to the TV using the 4 screws supplied.Fitting the Stand Neck and Base Together1. Fit the neck onto the base.2. Using 4 of the supplied screws, screw the neck to the base.Installing the Base Stand3Slide underthe lipSlide underthe lipSCARTSPDIFCoax.OUTVGAANT.HDMI 1(ARC)HDMI 2LANTableCushionedmaterialTV stand (supplied)LT-32C650_QSG.indd 1 17/04/2015 16:07

/ 2

Related manuals for JVC LT-32C650