JVC KM-F700U Instructions Manual

E-5Before connection, be sure to refer to the instruction manuals of the equipment to be used.1. CONTROLS, INDICATORS AND CONNECTORS9 [VIDEO OUTPUT] terminal(Mini D-Sub 15-pin, female)Connect to the video-input terminal of an SXGA-compat-ible monitor. Note that when a sync signal from the cam-era is not input to the 0 VIDEO INPUT terminal, no videosignal is output.0[VIDEO INPUT] terminal(Mini D-Sub 15-pin, female)Connect to the MONITOR terminal of the camera (KY-F70/KY-F70B).! [WEN] write enable output terminalOutputs through the WEN (write enable) signal input tothe 6 CAMERA CTL terminal.(For specifications and operations KY-F70/KY-F70BINSTRUCTION MANUAL.)@ [FLASH] control output terminalConnect the external flash to this unit. The FLASH signalfrom the camera (KY-F70/KY-F70B) is output from here.(For specifications and operations KY-F70/KY-F70BINSTRUCTION MANUAL.)# [FREEZE] control input terminalUsed to control the freeze operation of the camera (KY-F70/KY-F70B) using an external switch. The external switchoutput signal is output to the 6 CAMERA CTL terminal.$ [SEND] SCSI output control terminalUsed when images from the camera (KY-F70/KY-F70B)are output to a MO/ZIP® drive or a printer using an ex-ternal switch. The external switch output signal is outputto the 6 CAMERA CTL terminal.1-2 Rear PanelSENDDC 12V INSEE INSTRUCTION MANUALCAMERA CTLRS-232CFREEZEFLASHWENMODEOUTPUTVIDEOINPUT! @ # $5678901 2ON3 41ON 2 3 41ON 2 3 4Standard mode(1280 x 1024 pixels)Wide mode(1360 x 1024 pixels)5 [DC 12V IN] power input terminal(Mini DIN 8-pin, female)Supplies power (DC 12V) to the unit. Connect this termi-nal to an AA-P700 AC adapter (optional) using the powercable provided.6 [CAMERA CTL] Camera ControlterminalWhen connected to the camera (KY-F70/KY-F70B) us-ing the provided cable, camera operations such as AutoWhite Balance or Freeze can be controlled remotely.7 [RS-232C] serial remote terminal(D-Sub 9-pin, male)This terminal is used when remotely controlling the cam-era (KY-F70/KY-F70B) with a personal computer.Use the D-sub 9 pin cross cable, which is available on themarket.8 [MODE] select switchSelect the output screen mode with this switch.●Switches 2, 3 and 4 are not used. Leave them in OFF mode.MEMO● When using the Wide mode with the D-ILA Projectorconnected, set the CLAMP item to [ST] in the ONSCREEN menu.● When using the Wide mode, a distorted video may bedisplayed depending on which monitor is being used.In this case use the Standard mode.MEMO● The 7 RS-232C, ! WEN, @ FLASH, $ SEND and# FREEZE terminals only function when the 6 CAM-ERA CTL terminal of this unit is connected to the RE-MOTE terminal of a KY-F70/KY-F70B camera.● Image output to ZIP® drives is only possible with KY-F70B cameras.E-41 [POWER] display lampThis lights up when power is supplied to the unit.2 [AUTO WHITE] buttonPress this button to start the Auto White balance func-tion of an attached camera (KY-F70/KY-F70B).(Valid only when camera is in Auto White mode)3 [SEND] buttonWhen a camera is in Freeze mode, press this button tosend the image to an MO/ZIP® drive or a printer.1.CONTROLS, INDICATORS AND CONNECTORS4 [FREEZE] buttonWhen this button is pressed, the image from the camerawill be in the freeze mode (Still image), pressing the but-ton again will release it from this mode.MEMOSelect image output equipment using the menu of thecamera (KY-F70/KY-F70B). ( page 6.)● Image output to ZIP® drives is only possible with KY-F70B cameras.MEMOThe 2 AUTO WHITE, 3 SEND and 4 FREEZE buttonoperations are available only when the 6 CAMERA CTLterminal is connected to the REMOTE terminal of the cam-era (KY-F70/KY-F70B).1-1 Front PanelSCAN RATE CONVERTER KM-F700POWER1 2 3 4AUTO WHITE SEND FREEZEBefore connection, be sure to refer to the instruction manuals of the equipment to be used.Downloaded from: https://www.usersmanualguide.com/