JVC KD-SHX855 Installation & Connection Manual

Also see for EXAD KD-SHX855: Instructions Installation & connection manual

KD-SHX855Installation/Connection Manual安裝／連接手冊LVT1373-010A[UT]0405MNMMDWJEINEN, CTJHandles板條型把手GLock nut (M5)鎖定螺母 (M5)HMounting bolt (M5 x 20 mm)緊固螺栓 (M5 x 20 mm)IRubber cushion橡膠防震墊A / BHard case/Controlpanel硬盒／控制面板CSleeve夾子接頭DTrim plate裝飾框EPower cord電路連接用的配線束ENGLISHThis unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If yourvehicle does not have this system, a voltage inverter is required, which can be purchased atJVC car audio dealers.Parts list for installation and connectionThe following parts are provided for this unit.After checking them, please set them correctly.INSTALLATION (IN-DASH MOUNTING)The following illustration shows a typical installation. If you have any questions or requireinformation regarding installation kits, consult your JVC car audio dealer or a company supplyingkits.• If you are not sure how to install this unit correctly, have it installed by a qualified technician.LRemote controller遙控器MBattery電池Removing the unitBefore removing the unit, release the rear section.*1 When you stand the unit, be careful not to damage the fuse on the rear.*1 您豎起本機時，小心不要損壞底部的保險絲。*2 Fit the protrusions outside the unit.*2 將突出部分安置在本機外部。NCD-ROM(Image Converter:Color Ver. 2.0)CD-ROM(Image Converter:Color Ver. 2.0)FWasher (ø5)墊圈 (ø5)Do the required electricalconnections.進行所需的電路連接。Bend the appropriate tabs to hold thesleeve firmly in place.弄彎機殼的突舌，把外套機殼牢固在儀表板內。Insert the two handles, then pull themas illustrated so that the unit can beremoved.按圖所示，將兩片板條型把手插入卡槽，然後輕穩地從兩側向外拉兩片把手，本機隨之拉出。中文本機僅可使用直流 12 V、負極接地的電源系統。如果您的車輛沒有這一電源系統，則需要一個電壓變換器，可以在 JVC 汽車音響分銷商處買到。用於安裝和連接的零件裹下列零件是隨本機提供的。清點以後，正確地將其裝配。安裝（裝設、固定在儀表板內）下面的圖解表示了典型的安裝程序。如果您有問題，或需要有關配套元件的資料，請向 JVC汽車音響分銷商或配套元件供應公司詢問。• 如果您不能確定如何正確地安裝本機，應請合格的技術人員來安裝。拆卸本機在拆卸本機前，應將本機後部的固定和連接部分鬆開。KDC/DC converter直流電／直流電變流器When installing the unit without using the sleeve /若不使用外套機殼安裝本機In a Toyota for example, first remove the car radio and install the unit in its place.以豐田牌（TOYOTA）汽車為例 : 首先取出汽車收音機，然後將本機裝入其空出的位置。When using the optional stay /若選用支撐架Note : When installing the unit on the mounting bracket, make sure to use the8 mm-long screws. If longer screws are used, they could damage theunit.注意 : 把本機安裝在托座上時，務必使用 8 mm 長的螺絲釘。如使用過長的螺絲釘，會損壞本機。Bracket *3托座 *3*3 Not included for this unit.*3 不包含在本機內。Flat type screws(M5 x 8 mm) *3平頭螺絲釘(M5 x 8 mm) *3Pocket空殼Flat type screws(M5 x 8 mm) *3平頭螺絲釘(M5 x 8 mm) *3Install the unit at an angle ofless than 30˚.將本機安裝在少於 30˚ 的角度。Bracket *3托座 *3Dashboard儀表板Fire wall防火板Stay(option)支撐架（選用的）Screw (option)螺絲釘（選用的）Fit the unit into the mounting sleeve byusing four corners of the trim plate.• DO NOT press the panel (shaded in theillustration).將本機用四個角的裝飾框固定到安裝套內。• 不要擠壓面板（圖中的陰影部分）。Caution when installing /安裝注意事項1

/ 4

Related manuals for JVC EXAD KD-SHX855