JVC KD-AV7008 Installation & Connection Manual

Also see for KD-AV7008: Service manual

1KD-AV7008Installation/Connection ManualLVT1174-002A[A]This unit is designed to operate only on 12 V DC, NEGATIVE ground electrical systems. If yourvehicle does not have this system, a voltage inverter is required, which can be purchased at JVCcar audio dealers.WARNINGS• DO NOT install any unit in locations where;– it may obstruct the steering wheel and gearshift lever operations, as this may result in a trafficaccident.– it may obstruct the operation of safety devices such as air bags, as this may result in a fatalaccident.– it may obstruct visibility.• DO NOT operate any unit while manipulating the steering wheel, as this may result in a trafficaccident.• The driver must not watch the monitor while driving.If the driver watches the monitor while driving, it may lead to carelessness and cause an accident.• If you need to operate the main unit while driving, be sure to look ahead carefully or you may beinvolved in a traffic accident.• If the parking brake is not engaged, “DRIVER MUST NOT WATCH THE MONITOR WHILEDRIVING.” appears on the monitor, and no playback picture will be shown.– This warning appears only when the parking brake wire is connected to the parking brakesystem built in the car.Notes on mounting the hideaway unit• Mount on a firm surface, under the front seat or in the trunk.• Since heat is generated inside the unit, do not mount near inflammable objects. In addition, mountin an area that will not prevent the unit from dissipating heat.• Do not mount the unit in the places which are subject to heat such as near a radiator, in a glovecompartment or in insulated area such as under a car mat that will prevent the unit from dissipatingheat.Notes on electrical connections• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVCcar audio dealer.• Maximum input of the speakers should be more than 50 W at the rear, 50 W at the front, and35 W at the center, with an impedance of 4 Ω to 8 Ω.• Be sure to ground each unit to the car’s chassis.• The main unit and the hideaway unit become very hot after use. Be careful not to get burnedwhen removing them.• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.• Take preventative measures to avoid unexpected disconnection of the cords anddamage to the cords. This trouble may happen while moving or reclining the seat.1004MNMMDWJEINENParts lista Main unitr Washer—ø5 s Rubber cushionq Lock nut—M5b Hideaway unitt Remote controller u BatteryCR2025RM-RK220v Center speaker/rearcamera cordw Extension antenna cordC Sleeve-mounting platesType A Type Bd Fixing screws—M5 x 6 mme, f Power cordse For main unit: f For hideaway unit:g AV bus cable—2.5 mh Crimp connectors i Handles j Soft case k Trim platel Sleeve m Brackets n Fixing screws—M4 x 8 mmo Blind coverp Mounting bolt—M5 x 20 mmWhen installing the unit without using the sleeveIn a Toyota for example, first remove the car radio and install the unit in its place.Note : When installing the unit on the mounting bracket, make sure to use screws of properlength refering to the table above. If longer screws are used, they could damage the unit.Flat type screws* 2Bracket*2*2 Not included with this unit.Pocket1 2 3 4 56 7 8 9lr qpWhen using the optional stayScrew (option)Stay (option)Fire wallDashboardInstall the unit at an angle of less than 30˚, taking it into accountthat the monitor would eject when in use (see below).30˚Required space for the monitor ejection60˚105˚51.8143.31512.2mm177© 2004 Victor Company of Japan, LimitedUse the following screwsFor No.1 – 5 M5 x 8 mm*2For No.6 – 9 M4 x 3 mm*2

/ 4

Related manuals for JVC KD-AV7008