JVC 0303NHMMDWJEIN Instructions Manual

Also see for RX-7032VSL: Instructions Instructions Instructions Instructions Instruction manual

Contents

31EnglishYou can also use the remote control for adjusting the speakeroutput level.When using the remote control, you can make an adjustmentwhile listening to test tone.1. Press SOUND.The 10 keys are activated for sound adjustments.2. Press TEST to check if you can hear the sounds throughall the speakers at equal level.Test tone comes out of the speakers in the following order.• No test tone comes out of the speakers which are set to“NONE” in the speaker setting, and the subwoofer.FRNT L (Left front speaker) =CENTER (Center speaker) =FRNT R (Right front speaker) =SURR R (Right surround speaker) =SBACK (surround back speaker) =SURR L (Left surround speaker) =(Back to the beginning)3. Select a speaker you want to adjust.• To select the left front speaker, press FRONT•L.• To select the center speaker, press CENTER.• To select the right front speaker, press FRONT•R.• To select the right surround speaker, press SURR•R.• To select the surround back speaker, press SURR BACK.• To select the left surround speaker, press SURR•L.4. Press LEVEL + or – to adjust the speaker output level(–10 dB to +10 dB).5. Repeat steps 3 and 4 to adjust the other speaker’s outputlevels.6. Press TEST again to stop the test tone.Adjusting the Sound Parameters for theSurround and DSP ModesYou can adjust the Surround and DSP sound parameters to yourpreference.• When center speaker is set to “NONE,” CTR TONE, CNTRWIDTH, and CNTR GAIN are not available.7Adjustable parametersYou can adjust the following parameters:For Surround, DAP, and All Channel Stereo modes (when thecenter speaker is connected)• This setting is common to all surround modes, and ismemorized separately for DSP modes.CTR TONE: Adjust the center tone. As the numberincreases, the dialogue becomes clearer sothat the human voices change from soft tosharp. Normally select “3 (initial setting).”Adjustable range: 1 to 5For DAP modes• Once you have made an adjustment, it is memorized for eachDAP mode.EFFECT: Adjust the DAP effect level. As the numberincreases, the DAP effect becomes stronger.Normally select “3 (initial setting).”Adjustable range: 1 to 5ROOMSIZE: Adjust the virtual room size. As the numberincreases, the interval between reflectionsincreases so that you will feel as if you werein a larger room. Normally select “3 (initialsetting).”Adjustable range: 1 to 5LIVENESS: Adjust the liveness effect. As the numberincreases, the attenuation level of reflectionsover time decreases so that acoustics changefrom “Dead” to “Live.” Normally select “3(initial setting).”Adjustable range: 1 to 5For Pro Logic II Music onlyPANORAMA: Select “ON” to add “wraparound” soundeffect with side-wall image. (Initial setting:“OFF”)CNTR WIDTH: Adjust the center channel localizationbetween the center speaker and the left/rightfront speakers. As the number increases, thecenter channel sound moves toward the leftand right front speakers. Normally select “3(initial setting).”Adjustable range: OFF and 1 to 7DIMENSION: Adjust sound localization position. As thenumber increases, the sound localizationmoves towards forward from backward.Normally select “4 (initial setting).”Adjustable range: 1 to 7For Neo:6 Music onlyCNTR GAIN: Adjust the sound localization of the centerchannel. As the number increases, centerchannel will be localized clearly. Normallyselect “0.2 (initial setting).”Adjustable range: 0 to 0.52 315 648 97/P0 +1010/0