JVC 0209RYMMDWDAT Instructions Manual

CAUTION: Proper VentilationTo avoid risk of electric shock and fire, and to preventdamage, locate the apparatus as follows:1. Front: No obstructions and open spacing.2. Sides/Top/Back: No obstructions should be placed in theareas shown by the dimensions below.3. Bottom: Place on the level surface. Maintain an adequateair path for ventilation by placing on a stand with a heightof 10 cm or more.ATTENTION: Aération correctePour prévenir tout risque de décharge électrique oud’incendie et éviter toute détérioration, installez l’appareil dela manière suivante:1. Avant: Bien dégagé de tout objet.2. Côtés/dessus/dessous: Assurez-vous que rien ne bloqueles espaces indiqués sur le schéma ci-dessous.3. Dessous: Posez l’appareil sur une surface plane ethorizontale. Veillez à ce que sa ventilation correcte puissese faire en le plaçant sur un support d’au moins dixcentimètres de hauteur.Connections For iPodUsing HeadphonesBe sure to turn down the volume before connecting or putting onthe headphones.• Connecting the headphones will deactivate the speakers.• Sound adjustments also affect the sound through the headphones.Display DemonstrationWhen you plug in the System, the display demonstrationautomatically starts.To cancel the display demonstration, press and hold DEMO until“DEMO CLR” is displayed while the System is on standby.• When the ECO Mode is activated, the display demonstration doesnot work (and you cannot deactivate it).• When the display demonstration is activated, it also starts if nooperation is done for about 2 minutes while the System is turnedon.Laser Touch OperationYou can use 4/¢ and VOL +/– on the front panel by slidingyour finger up or down on the illumination.Motion Sensor on the Front PanelWhen you move your hand close to the front panel while the Systemis on standby, the controls on the front panel illuminate.• When no operation is done for about 5 seconds, the illuminationturns off.• When the ECO Mode is activated, the motion sensor does not work.INSTRUCTIONSLVT1989-001A[J/C]0209RYMMDWDAT©2009 Victor Company of Japan, Limited12 4Basic and Common OperationsSupplied AccessoriesAfter unpacking, check to be sure that you have all thefollowing items.• Remote control, RM-SUXGN6J (× 1)• Lithium coin battery (× 1: installed in the remote control)• AM loop antenna (× 1)• FM antenna (× 1)• Video cord (× 1)If anything is missing, consult your dealer immediately.Prepare the Remote ControlWhen you use the remote control for the first time, pull outthe insulation sheet.To Replace the Battery in the Remote ControlNOTES:• Store the battery in a place where children cannot reach. Ifa child accidentally swallows the battery, consult a doctorimmediately.• To prevent the battery from overheating, cracking, or startinga fire:– Do not recharge, short, disassemble or heat the battery ordispose of it in a fire.– Do not leave the battery with other metallic materials.– Wrap the battery with tape and insulate when throwingaway or saving it.– Do not poke the battery with tweezers or similar tools.• Dispose of battery in the proper manner, according to federal,state, and local regulations.Basic Disc/USB Mass Storage Class Device OperationsTo Press Indication/ResultPlay back the disc • During playback, press again to pause.Play back the USBmass storage classdeviceStop playback • While playback is stopped, total track numberand total playing time (for MP3/WMA files,group number and track number) appear.Select a track Select the next tracks.To go back to the beginning of the current orprevious tracks.Select a group(MP3/WMA only)Select the next groups.Select the previous groups.Forward search/Reverse searchPress and hold to fast-forward the track duringplayback.Press and hold to fast-reverse the track duringplayback.Changethe displayinformation(only for USB)Press repeatedly.NOTES:• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or“NO USB” appears on the main display.• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,“NO PLAY” appears on the main display.Playing Repeatedly—Repeat Play1 Press repeatedly to specify the repeat mode as follows:RPT TRK: Repeats the current (or specified) track. [ 1]RPT GRP: Repeats all tracks in the current group (MP3/WMAonly). [ ]RPT ALL: Repeats all tracks. [ ALL ]RPT OFF: Normal playback2 orGetting Started Playing Back a Disc/USB Mass Storage Class DeviceMICRO COMPONENT SYSTEMUX-GN6—Consists of CA-UXGN6 and SP-UXGN5This System can play back...– CD.– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA filesin ISO 9660 format.– USB mass storage class device containing MP3/WMA files.• When playing back an MP3 or WMA track, corresponding indicator lights up.Loading a Disc (on the System only)1 Touch to open the disc tray.2 • When using an 8 cm (3 3/16 inch) disc, place it onthe inner circle of the disc tray.3 Touch to close the disc tray.Connecting a USB Mass Storage Class DeviceYou can connect a USB mass storage class device such as a USB flash memorydevice, MP3 player, multimedia card reader, etc. to the System.Front viewNOTES:• When connecting with a USB cable, use the USB 2.0 cable whose length is less than1 m (3.3 ft).• USB mass storage class device is charged through the USB terminal when the Systemis turned on and the source is “USB.”• You cannot connect a computer to the USB terminal of the System.• Do not disconnect the USB mass storage class device when the System is turned on. Itmay cause malfunction of both this System and the device.• Noise and static electricity may stop the USB mass storage class device sound. In thiscase, disconnect the USB mass storage class device and connect it again after turningoff the System.• Depending on the shape of USB mass storage class device, the USB terminal maynot be fully inserted into the USB terminal on the System. In such a case, use a USBextension cable (not supplied) to connect.Prohibiting Disc Ejection (on the System only)You can lock the disc tray so that no one can eject the loaded disc.While the System is on standby...To cancel the prohibition, repeat the sameprocedure.3Programming the Playing Order—Program Play(only for Disc)1 Select disc as the source.2 Activate the Program Play.3 orSelect tracks you want for Program Play.• For MP3/WMA files only: You can also use UP orDOWN.4 Press to store the selected track.5 Repeat steps 3 and 4 to program other tracks you want.• If you try to program a 33rd track, “PGM FULL” appears.6 The tracks are played back in the programmedorder.Operations for Program Play (while not playing)• To check the programmed contents, press 4 or ¢.• To add tracks, repeat steps 3 and 4 above.• To erase the entire program, press and hold CANCEL for about 2 seconds.• To exit from Program Play, press PROGRAM or 7.– The stored program is kept.Playing at Random—Random Play (only for Disc)1 Select disc as the source.2 Press repeatedly to select the desired Random Mode.RANDOM: Plays all tracks in random order. [ALL RND ]RND GRP: Plays tracks in the current group in randomorder. (MP3/WMA only). [ RND ]RND OFF: Normal playback3 Playback starts in random order.Operations for Random Play• To skip a track, press ¢.• To go back to the beginning of the current track, press 4.Thank you for purchasing a JVC product.ToPressIndication/ResultMainunit RemoteTurn on or off(standby) the powerThe STANDBY lamp on the System turns off/on.Select a source See “Playing Back a Disc/USB Mass Storage Class Device”on page 4.See “Listening to an iPod/Viewing Images on the iPod”on page 5.Press repeatedly to select “FM,” “AM,” or “AUDIO IN” asthe source.• See “Listening to FM and AM Broadcasts” or “Listeningto Other Equipment” on page 5.Adjust the volume—Drop the volume ina moment — To restore the volume, press again, or adjust thevolume level.Select the SoundMode—Press repeatedly to select the desired Sound Mode.The SOUND indicator lights up.Emphasize thesound (SoundTurbo)The S.TURBO indicator lights up.To cancel this function, press again.Reinforce the basssound (Hyper BassSound) —The HBS indicator lights up.• When Sound Turbo function is activated (see above),the HBS indicator goes off and HBS button does notwork.To cancel this function, press again.Change the displaybrightnessPress repeatedly when the System is turned on.Turn off the displaywhile on standbyPress repeatedly while the System is on standby.ClockDISP OFF:ECO ON:Turns off the display with the motion sensoron.Turns on the ECO (Ecology) Mode.ECO Mode reduces power consumptionwhile the System is on standby by turningoff the display and motion sensor.NOTE:DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the suddenblast of sound can damage your hearing, speakers and/or headphones when you turn on the System or startplayback.Rear viewOutdoor FM antenna(not supplied)FM antenna (supplied)NOTES:• Make sure the antenna conductors do not touch any otherterminals, connecting cords and power cord. Also, keep theantennas away from metallic parts of the System, connectingcords, and the AC power cord. This could cause poor reception.• Keep the AM loop antenna cable wrapped around the AM loopantenna frame, otherwise the effectiveness and sensitivity of theAM loop antenna may be reduced.• Make sure both the speakers are connected correctly and firmly.• When connecting the speaker cords, match the polarity of thespeaker terminals: red color to (+) and black color to (–).• DO NOT connect more than one speaker to each terminal.• DO NOT allow the conductor of the speaker cords to be in touchwith the metallic parts of the System.Do not connect the AC power cord until all other connections have been made.To connect the FM antenna (supplied)Extend it so that you can obtain the best reception.For better FM receptionDisconnect the supplied FM antenna, and connectto an outdoor FM antenna using a 75 Ω wire withcoaxial type connector.Press and holdInsertReleaseRedBlackFrom leftspeakerFrom rightspeakerLVT1989-001A EN_UX-GN6[JC]USB cable (notsupplied)orUSB memory(not supplied)STANDBY lampStereo mini plug cordPHONES jackTouch to turn on the System.To use 4/¢ To use VOL +/–To a wall outletPlug the AC power cord only after allconnections are complete.CA-UXGN6 CA-UXGN6Turn the AM loop antenna untilthe best reception is obtained.To connect the AM loop antennaTo assemble the AM loop antenna (supplied)RedBlackTo connect the speaker cordsFor customer use:Enter below the Model No. and Serial No. which arelocated either on the rear, bottom or side of the cabinet.Retain this information for future reference.Model No.Serial No.Warnings, Cautions and OthersMises en garde, précautions et indicationsdiversesThe lightning flash with arrowhead symbol,within an equilateral triangle is intended toalert the user to the presence of uninsulated“dangerous voltage” within the productsenclosure that may be of sufficient magnitudeto constitute a risk of electric shock to persons.The exclamation point within an equilateraltriangle is intended to alert the user tothe presence of important operating andmaintenance (servicing) instructions in theliterature accompanying the appliance.For U.S.A.This equipment has been tested and found to complywith the limits for a Class B digital device, pursuant to part15 of the FCC Rules.These limits are designed to provide reasonableprotection against harmful interference in a residentialinstallation. This equipment generates, uses and canradiate radio frequency energy and, if not installed andused in accordance with the instructions, may causeharmful interference to radio communications. However,there is no guarantee that interference will not occurin a particular installation. If this equipment does causeharmful interference to radio or television reception, whichcan be determined by turning the equipment off and on,the user is encouraged to try to correct the interference byone or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment andreceiver. Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technicianfor help.Le symbole de l’éclair à l’intérieur d’un triangleéquilatéral est destiné à alerter l’utilisateur surla présence d’une “tension dangereuse” nonisolée dans le boîtier du produit. Cette tensionest suffisante pour provoquer l’électrocutionde personnes.Le point d’exclamation à l’intérieur d’untriangle équilatéral est destiné à alerterl’utilisateur sur la présence d’opérationsd’entretien importantes au sujet desquellesdes renseignements se trouvent dans lemanuel d’instructions.IMPORTANT FOR LASER PRODUCTS1. CLASS 1 LASER PRODUCT2. CAUTION: Do not open the top cover or cabinet. Thereare no user serviceable parts inside the unit; leave allservicing to qualified service personnel.3. CAUTION: Visible and/or invisible class 1M laser radiationwhen open. Do not view directly with optical instruments.4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACEDINSIDE THE UNIT.IMPORTANT POUR PRODUITS LASER1. PRODUIT LASER CLASSE 12. ATTENTION: N’ouvrez pas le couvercle supérieur nile coffret de l’appareil. Il n’y a aucune pièce réparablepar l’utilisateur à l’intérieur de l’appareil; confiez touteréparation à un personnel qualifié.3. ATTENTION: Rayonnement laser visible et/ou invisiblede classe 1M une fois ouvert. Ne pas regarder directementdans le faisceau avec des instruments optiques.4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DEPRÉCAUTION PLACÉE À L’INTERIEUR DE L’APPAREIL.CAUTION:Changes or modifications not approved by JVC could voidthe user’s authority to operate the equipment.[European Union only][Union européenne seulement]CAUTIONThe button in any position does not disconnect the mainsline.Disconnect the mains plug to shut the power off completely(the STANDBY lamp goes off).The MAINS plug or an appliance coupler is used as thedisconnect device, the disconnect device shall remain readilyoperable.• When the System is on standby, the STANDBY lamp lightsred.• When the System is turned on, the STANDBY lamp goes off.The power can be remote controlled.ATTENTIONLa touche , quelle que soit sa position, ne coupe pas laligne principale.Débrancher la fiche principale pour couper complètementl’alimentation du secteur (le témoin STANDBY s’éteint).La fiche secteur ou un coupleur est utilisé comme dispositifde déconnexion de l’appareil, et l’appareil déconnecté doitêtre prêt à être utilisé.• Quand l’appareil est en mode d’attente, le témoin STANDBYest allumé en rouge.• Quand l’appareil est sous tension, le témoin STANDBY s’éteint.L’alimentation peut être commandée à distance.WARNING: TO REDUCE THE RISK OF FIRE ORELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCETO RAIN OR MOISTURE.CAUTIONTo reduce the risk of electrical shocks, fire, etc.:1. Do not remove screws, covers or cabinet.2. Do not expose this appliance to rain or moisture.ATTENTIONAfin d’éviter tout risque d’électrocution, d’incendie, etc.:1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir lecoffret de l’appareil.2. Ne pas exposer l’appareil à la pluie ni à l’humidité.CAUTION:• Do not block the ventilation openings or holes. (If theventilation openings or holes are blocked by a newspaperor cloth, etc., the heat may not be able to get out.)• Do not place any naked flame sources, such as lightedcandles, on the apparatus.• When discarding batteries, environmental problemsmust be considered and local rules or laws governing thedisposal of these batteries must be followed strictly.• Do not expose this apparatus to rain, moisture, drippingor splashing and that no objects filled with liquids, such asvases, shall be placed on the apparatus.For USA-California OnlyThis product contains a CR Coin Cell Lithium Battery whichcontains Perchlorate Material – special handling mayapply.See www.dtsc.ca.gov/hazardouswaste/perchlorateRemote sensorCAUTION: Excessive sound pressure from earphones orheadphones can cause hearing loss.ATTENTION: Une pression acoustique excessive des écouteursou du casque d’écoute peut entraîner une perte auditive.Lithium coin battery(product number: CR2025)Insulation sheetTo connect the monitor(not supplied)—To view video/picturefrom the iPodSP-UXGN5CAUTION: Battery shall not be exposed to excessive heatsuch as sunshine, fire, or the like.ATTENTION: Les piles ne doivent en aucun cas êtreexposées à une chaleur excessive (lumière du solei, feu,etc.).SP-UXGN5Point at the remote sensor on the front panel.Headphones(not supplied)CAUTION:Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.MonitorVideo cord(supplied)The operations on pages 4 to 6 are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also beused for the operations.(canceled)AM loop antenna(supplied)(canceled)ATTENTION:• Ne bloquez pas les orifices ou les trous de ventilation. (Siles orifices ou les trous de ventilation sont bloqués par unjournal un tissu, etc., la chaleur peut ne pas être évacuéecorrectement de l’appareil.)• Ne placez aucune source de flamme nue, telle qu’unebougie, sur l’appareil.• Lors de la mise au rebut des piles, veuillez prendre enconsidération les problèmes de l’environnement et suivrestrictement les règles et les lois locales sur la mise au rebutdes piles.• N’exposez pas cet appareil à la pluie, à l’humidité, à unégouttement ou à des éclaboussures et ne placez pas desobjets remplis de liquide, tels qu’un vase, sur l’appareil.Front/Face Side/Côté