Husqvarna DM230 Safety Instructions

Also see for DM 230: Price list Operator's manual Operator's manual Operator's manual Operator's manual

- 3 -Need It. Rent It!• DM 230 has three speed ranges for drill bit sizes up to 150 mm.• The machine has a water cooled gearbox with a pipe that runs through the spindle.• DM 230 can also be connected to a vacuum cleaner with the help of an adapter, used for dry drilling, which is attached to the spindle.• The drilling machine is equipped with SoftstartTM, ElgardTM and speed control.SoftstartTMSoftstartTM is an electronic power limitation, making it easier to start the drill. Maximum speed is reached in about three seconds after the powerswitch is pressed in.STARTING AND STOPPINGBefore startingMake sure that:The switch is undamaged. If not, the switch must be replaced by an authorized repairman.The switch is not sticking.The drill and its equipment are correctly installed:The drill is secured properly.If a stand is used, it must be attached to the machine by the fastening neck on the gearbox.Wear personal protective equipment. See instructions under the heading Personal protective equipment.The water cooling or vacuum cleaner (with the help of adapter) are attached to the machine. Use suitable drill bits depending on whether water ordry drilling is being performed. In the event of uncertainty contact your dealer, your service workshop or an experienced operator.StartingIMPORTANT! Changing gear may only be done when the machine is switched off. Otherwise there is a risk of damaging the gearbox.1 Set the working speed by turning the drill spindle and at the same time move the gear knob to the required position.2 Turn on the water cooling (wet drilling) or switch on the vacuum cleaner (dry drilling).3 Hold the machine steady.4 Press in the switch fully. Also press, if desired, the SmartstartTM button.StoppingWARNING! The drill bit continues to rotate for a while after the motor has been switched off. Do not stop the drill bit with your hands. Personalinjuries can occur.CoolingRun the machine unloaded for a minute or two to cool the motor.WORKING TECHNIQUESGeneral working instructionsWARNING! This section takes up the basic safety precautions for working with the drilling machine. This information is never a substitute forprofessional skills and experience. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact yourdealer, service agent or an experienced drilling machine user. Do not attempt any task that you feel unsure of!WARNING! Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation. Contact your doctorif you experience symptoms of overexposure to vibration. Such symptoms include numbness, loss of feeling, tingling, pricking, pain, loss of strength,changes in skin color or condition. These symptoms normally appear in the fingers, hands or wrists. These symptoms may be increased in coldtemperatures.Do not use the machine in bad weather, such as dense fog, rain, strong wind, intense cold, etc. Working in bad weather is tiring and can lead todangerous conditions, e.g. slippery surfaces.Never start to work with the power cutter before the working area is clear and you have a firm foothold. Look out for any obstacles with unexpectedmovement. Ensure when cutting that no material can become loose and fall, causing operating injury.Never perform handheld drilling from a ladder. Use the stand for safe drilling.Remain at a distance from the drill bit when the motor is running.Ensure that the working area is sufficiently illuminated to create a safe working environment.Make sure that no pipes or electrical cables are routed in the area to be drilled.Ensure the cord is behind you when you start to use the machine so that the cord will not be damaged.Never leave the machine unsupervised with the motor running. A rotating drill bit can entail a risk of serious injury.Always unplug the machine during longer work breaks.Do not overload the machine. Overloading can damage the machine.Keep tools sharp and clean in order to enable safer work.Always check the rear side of the surface where the drill bit will emerge when drilling right through. Secure and cordon off the area and make surethat no one can be injured or material damaged.

/ 4

Related manuals for Husqvarna DM 230