Husqvarna AUTOMOWER 310 Operator's Manual

Also see for 315, 320: Operator's manual Operator's manual Quick guide Operator's manual Operator's manual

3.20.3.2 GuideUse the number keys to enter the delay time.The delay time is normally specified as a figure between0 and 10 minutes.3.20.3.3 Guide > Disable / EnableNormally the Guide method does not need to bedeactivated even if there is no guide wire installed.However, to disable the Guide method, selectDisableand press OK.3.20.3.4 Guide > More > Test guideTesting selected settings can be seen as a natural partof the installation.1. Place the robotic lawnmower about 3 m from theguide wire, facing the wire.2. The test function is found inInstallation >Findcharging station >Guide.3. SelectMore and press OK.4. SelectTest Guide, and press OK.5. Press START and close the hatch.6. Check that the robotic lawnmower follows the guidewire all the way to the charging station and that itdocks with the charging station. The test is approvedonly if the robotic lawnmower is able to follow theguide wire the entire distance to the charging stationand docks at the first attempt. If the roboticlawnmower is unable to dock on the first attempt, itwill automatically try again. The installation is notapproved if the robotic lawnmower needs two ormore attempts to dock with the charging station.3.20.3.5 Guide > More > ResetThe specific settings for each method,Guide can bereset to factory settings.1. To reset, select the method using the left and rightarrow keys followed by OK.2. SelectMore, thenReset and press OK.3.20.3.6 Boundary loopUse the number keys to enter the delay time.This time is normally longer than forGuide as it isnormally better if the robotic lawnmower follows theguide wire home to the charging station. The delay timeis normally specified as a figure between 10 and 20minutes but can be shorter if the guide wire is notinstalled and it is unlikely that the robotic lawnmowercan find the charging station through an irregular search.Note: If the robotic lawnmower passes a guide wirewhile following the boundary wire, it will stop searchingalong the boundary wire and instead start to follow theguide wire into the charging station.3.20.3.7 Boundary loop > Disable / EnableIf it is very inappropriate in the installation to follow theboundary loop, the Boundary method checkbox has tobe deactivated. To disable the boundary method, selectDisable and press OK.3.20.3.8 Boundary > More > Test right / Test leftTesting selected settings can be seen as a natural partof the installation. Using the Test function, the roboticlawnmower travels the maximum distance from the wiredefined by the selected corridor width.1. Place the robotic lawnmower about 3 m from theboundary wire, facing the wire.2. The test function is found inInstallation >Findcharging station >Boundary.3. SelectMore and press OK.4. SelectTest right/Test left, and press OK.5. Press START and close the hatch.6. Check that the robotic lawnmower follows the guidewire all the way to the charging station and that itdocks with the charging station. The test is approvedonly if the robotic lawnmower is able to follow theguide wire the entire distance to the charging stationand docks at the first attempt. If the roboticlawnmower is unable to dock on the first attempt, itwill automatically try again. The installation is notapproved if the robotic lawnmower needs two ormore attempts to dock with the charging station.Normal causes as to why the robotic lawnmower cannotfollow the wire are that obstacles close to the wire havenot been isolated or that the guide wire has not beenlaid at an angle on a steep slope. Check that thecharging station, the boundary wire and the guide wireare installed in accordance with the instructions inLaying the boundary wire on page 16, inPlan where tolay the boundary wire on page 13 and inLaying andconnecting the guide wire on page 18.3.20.3.9 Boundary > More > ResetThe specific settings for each method,Boundary can bereset to factory settings.1. To reset, select the method using the left and rightarrow keys followed by OK.2. SelectMore, thenReset and press OK.3.20.3.10 Charging station rangeThere may be reasons to reduce the range of thecharging station in rare cases. It may be necessary if forinstance the charging station is placed close to a bush30 - Installation 840 - 001 -