Honeywell DX100 (M) Quick Start Manual

Honeywell DX100 (M) Quick Start Manual Manual pdf 1 page image

1 211DX100 (M)TERMINATION UNITMAN0617 Issue 03 February 20032104M0703Quick Start GuideThe DX100 (M) Termination Unit is an explosion proof active junction box thatprovides a signal connection point for the Searchpoint Optima and Searchline Excelrange of gas detectors and the associated field wiring, and a mounting point for theSearchpoint Optima and Optima Plus detectors. The unit is certified to UL and CSAstandards and is intended for use in hazardous environments.The Termination Unit also provides a digital interface between the attached gas detectorand an RS485 link to the network controller.Note: Gas detector digital address configuration information is not provided here but inthe DX100 Series Termination Units Technical Handbook.The DX100 (M) provides:• terminals for connecting the gas detector and the field cabling• an Intrinsically Safe (IS) connection point for the Hand HeldInterrogator (SHC1)• a local mounting point for the Searchpoint Optima or Optima Plus gasdetectorThe unit features three 3/4” NPT cable/conduit entries, two terminal blocks and a voltageclamp with a communications link entry socketWhen used with an Optima or Optima Plus, one of the unit’s three cable/conduit entries(usually the left-hand one) is used to mount the gas detector directly to the box. The gasdetectors output a 4-20mA signal that is sent via the Termination Unit and field wiring backto the system controller.The voltage clamp and the external socket provide the IS connection to theHandheld Interrogator (SHC1) which allows operator interaction with the attached gasdetector to commission, calibrate or diagnose the system. Full details about the gasdetectors can be found in their respective technical documents, which include operation ofthe SHC1.Caution: Only the SHC1 Handheld Interrogator should be connected to theDX100 (M) communication link entry socket.This guide covers the basic on-site mechanical and electrical installation of the unit. Referto the DX100 Series Termination Units Technical Handbook (Part No: 2104M0701) formore detailed information about the DX100 (M).Information noticesThe types of information notices used throughout this document are as follows:WARNINGSIndicates hazardous or unsafe practice that could result in severe injury ordeath to personnel.Caution: Indicates hazardous or unsafe practice which could result inminor injury to personnel, or product or property damage.Note: Provides useful/helpful/additional information.1. INTRODUCTION6. CERTIFICATION CERTIFICATIONThis section specifies UL and CSA certification information for the DX100 (M)Termination Unit. It includes relevant Control Drawings.A Honeywell Analytics certification label is located on the right-hand side of the DX100 (M) Termination Unit.The label contains all the relevant information regarding theproduct’s identification and certification state.The following diagram shows the UL/CSACertification Label.The part number for the DX100 (M) Termination Unit is2104B2382.UL/CSA Certification LabelUL Control DrawingTERMINATIONUNIT DX100 (M)UL FILE E136193COMMUNICATIONSFIXED SOCKET I.S.OUTPUT TO CALIBRATOR.(FACTORY FITTED)NOTE 2CONTROLEQUIPMENTNOTE 1SENSORANY SUITABLE UL LISTEDOR CLASSIFIED EXPLOSIONPROOF APPARATUS.HANDHELDCALIBRATORTYPE SHC 1UL FILE E136193NOTES:1. APPARATUS WHICH IS UNSPECIFIED EXCEPT THAT ITMUST NOT BE SUPPLIED FROM, NOR CONTAIN IN NORMALOR ABNORMAL CONDITIONS A SOURCE OF POTENTIALWITH RESPECT TO EARTH IN EXCESS OF 250V rmsOR 250V d.c.2. WIRING FROM THE HANDHELD CALIBRATOR (SHC1) TOTHE TERMINATION UNIT (DX100) IS NOT TO EXCEED15 METRES MAX.3. INSTALL EQUIPMENT INCLUDING FIELD WIRING INACCORDANCE WITH ARTICLES OF THE NATIONALELECTRICAL CODE FOR DIVISION 1HAZARDOUSLOCATIONS.SENSOR ENTRY(CONDUIT CONNECTIONREQUIRED WITH SEAL)NON HAZARDOUS AREASUPPLY ENTRY (CONDUITCONNECTION REQUIREDWITH SEAL)OPTIONAL TRANSMITTERSEARCHLINE EXCEL FILENo. E91044TRANSMITTER ENTRYP(CONDUITCONNECTIONPREQUIRED WITH SEAL)HAZARDOUS (CLASSIFIED) LOCATIONCLASS 1 DIV. 1 GROUPS B,C,D.2. SAFETYEnsure that you read and understand this document BEFORE installing/operating the equipment. Pay particular attention to the Safety Warnings.WARNINGS1. The DX100 (M) Termination Unit is certified for and intended for use inpotentially hazardous areas. Install and use the DX100 (M) Termination Unitin accordance with the latest regulations. No modifications to the unit ispermitted without reference to the relevant certifying authority2. Install UL approved and certified equipment including field wiring in strictaccordance with the articles of the National Electrical Code for Division 1Hazardous Locations (NFPA 70).3. Install CSA approved and certified equipment including field wiring in strictaccordance with Canadian Electrical Code, Part 1.4. For installations elsewhere, the appropriate local or national regulationsshould be used.5. The Code of Practice regarding Selection, Installation, Use And MaintenanceOf Apparatus For The Detection Of Combustible Gases (Other Than ForMining Applications Or Explosive Processing And Manufacture) must becomplied with.6. The DX100 (M) Termination Unit must be properly earthed to protect againstelectrical shock, minimise electrical interference and comply with IS SafetyRequirements.7. Dismantling or repair of equipment should be carried out in the safe areaonly.8. Do not drill holes in the housing as this will invalidate the explosion protection.9. In order to maintain electrical safety, the unit must not be operated inatmospheres with more than 21% oxygen.10. Do not open the enclosure in the presence of an explosive atmosphere.CAUTIONSOnly the Handheld Interrogator (SHC1) must be connected to theTermination Unit’s communication link entry socket.Honeywell Analytics reserve the right to change or revise the information supplied in thisdocument without notice and without obligation to notify any person or organization ofsuch revision or change. If further details are required that do not appear in thisdocument contact Honeywell Analytics or one of its agents.CSA Control DrawingSENSOR ENTRY(CONDUIT CONNECTIONREQUIRED WITH SEAL)NON HAZARDOUS AREASUPPLY ENTRY (CONDUITCONNECTION REQUIREDWITH SEAL)COMMUNICATIONSFIXED SOCKET I.S.OUTPUT TO CALIBRATOR.(FACTORY FITTED)NOTE 2CONTROLEQUIPMENTNOTE 1SENSORTERMINATIONUNIT DX100 (M)CSA FILE LR48148TRANSMITTER ENTRYP(CONDUITCONNECTIONPREQUIRED WITH SEAL)HAZARDOUS (CLASSIFIED) LOCATIONCLASS I, DIV. 1 GROUPS B,C,D.ANY SUITABLE CSA LISTEDOR CLASSIFIED EXPLOSIONPROOF APPARATUS.HANDHELDCALIBRATORTYPE SHC 1CSA FILE LR48148OPTIONALTRANSMITTERSEARCHLINE EXCELFILE No. LR48148NOTES:1. APPARATUS WHICH IS UNSPECIFIED EXCEPT THAT ITMUST NOT BE SUPPLIED FROM, NOR CONTAIN IN NORMALOR ABNORMAL CONDITIONS A SOURCE OF POTENTIALWITH RESPECT TO EARTH IN EXCESS OF 250V rmsOR 250V d.c.2. WIRING FROM THE HANDHELD CALIBRATOR (SHC1) TO THETERMINATION UNIT (DX100) IS NOT TO EXCEED15 METRES MAX.3. INSTALL EQUIPMENT INCLUDING FIELD WIRINGIN ACCORDANCE WITH CANADIANELECTRICAL CODE, PART 1CERTIFICATION14This publication is not intended to form the basis of a contract, and the company reserves theright to amend the design and specification of the instruments without notice.A company of the Zellweger Luwa Grouptotal environmental solutionsCertification labelMEMBERS OF THE ZELLWEGER ANALYTICS DIVISIONUK AND INTERNATIONALENQUIRIESZellweger Analytics LtdHatch Pond House4 Stinsford RoadNuffield EstatePooleDorsetBH17 0RZ, UKTel: +44 (0)1202 676161Fax: +44 (0)1202 678011Email: sales@zelana.co.ukASIA PACIFICZellweger Analytics LtdAsia Pacific Regional Office1 Scotts Road#25-04 Shaw CentreSingapore 228208Tel: +65 6862 7701Fax: +65 6862 3858Email:zalasia@singnet.com.sgBELGIUMZellweger Analytics NVLeuvensesteenweg 392aChee de LouvainB-1932 ZaventemBelgiumTel: +32 27140311Fax: +32 27140344Email: zabl@zelana.comFRANCEZellweger Analytics France SALes Fermes Californiennes62 avenue de l’EuropeEmerainville77436 MARNE LA VALLEECEDEX 2FranceTel: 33 (1) 60 95 45 46Fax: 33 (1) 60 95 45 50GERMANYZellweger Analytics GmbHSollner Strasse 65bD-81479 MunchenGermanyTel: +49 89 791 920Fax: +49 89 791 9243Email:vertriebscenter@zelana.deITALYZellweger Analytics srlVia F. Primaticcio 1681-20147 MilanoItalyTel: +39 0248 3391Fax: +39 0248 3023 14Email: zaitaly@zelana.comMIDDLE EASTZellweger Analytics LimitedPO Box 52196Dubai UAETel: +971 4 3458 338Fax: +971 4 3458 778Email:zelana@emirates.net.aeNETHERLANDSZellweger Analytics BVPostbus 157NL-3740AD BaarnTel: +31 (0)355435646Fax: +31 (0)355435929Email: zabl@zelana.comSPAINZellweger Analytics SAAvda Remolar 3108820 El Prat de LlobregatBarcelonaSpainTel: +34 93 379 9611Fax: +34 93 379 8551Email: zellana@jet.esUSAZellweger Analytics, Inc.5089 Bristol Industrial WaySuite B & CBuford, Georgia 30518USATel: +1 770 831 4800Toll Free: +1 800 535 0606Fax: +1 678 546 1954Email: sales@zelana.com13126. SPECIFICATIONSConnectionsInputsOutputsPower SupplySearchpoint OptimaSearchpoint Optima PlusSearchline ExcelSearchline Excel Cross-DuctField wiring.IS protected Honeywell SHC1 HandheldInterrogator communications (RS485)4-20mA (Non-isolated).18-32VDC.EnvironmentalOperating temperature UL -25°C to 40°C (-13°F to 104°F).CSA -55°C to 40°C (-67°F to 104°F).EnclosureEntry Socket One IS protected Communications Link Entry Socketfor connecting the Honeywell SHC1 Handheldinterrogator.Cable/Conduit Entries Three 3/4 NPT entries (one each side and one in thebottom) to accept gas detector and field cabling or 3/4”conduit.Size 212mm (8.35in.) wide x 152.4mm (6in.) high xWeightMaterialIngress ProtectionCertificationDigital Interface117.5mm (4.625in.) deep. Add approximately 60mm(2.36in.) to the height for the Communications LinkEntry Socket.2.5kg.Aluminium.IP66 to BS EN 60529, Degrees of protection providedby enclosures (IP code).UL Class I, Div 1, Groups B, C, DCSA Class I, Div 1, Groups B, C, D(see Certification for details)Use the Modbus® RTU communications protocolField Wiring from 22-12 AWG (0.326 to 3.31mm 2), 105CDX100 (M) Termination UnitQuick Start GuideIssue a3 03/2017H_MAN0617_V12104-M-0703© 2017 Honeywell Analytics11179Please Note:While every effort has been made to ensureaccuracy in this publication, no responsibilitycan be accepted for errors or omissions. Datamay change, as well as legislation, and youare strongly advised to obtain copies of themost recently issued regulations, standards,and guidelines.This publication is not intended to form thebasis of a contract.© 2017 Honeywell AnalyticsFind out more at:www.honeywellanalytics.comContact Honeywell Analytics:Europe, Middle East, AfricaLife Safety Distribution GmbHJavastrasse 28604 HegnauSwitzerlandTel: +41 (0)44 943 4300Fax: +41 (0)44 943 4398gasdetection@honeywell.comCustomer Service:Tel: 00800 333 222 44 (Freephone number)Tel: +41 44 943 4380 (Alternative number)Fax: 00800 333 222 55Middle East Tel: +971 4 450 5800 (Fixed Gas Detection)Middle East Tel: +971 4 450 5852 (Portable Gas Detection)AmericasHoneywell Analytics Inc.405 Barclay Blvd.Lincolnshire, IL 60069USATel: +1 847 955 8200Toll free: +1 800 538 0363Fax: +1 847 955 8210detectgas@honeywell.comAsia PacificHoneywell Analytics Asia Pacific#701 Kolon Science Valley (1)34 Worldcup Buk-ro, Mapo-gu,Seoul 03922,KoreaTel: +82 (0)2 6909 0300Fax: +82 (0)2 2025 0328India Tel: +91 124 4752700analytics.ap@honeywell.comTechnical ServicesEMEA: HAexpert@honeywell.comUS: ha.us.service@honeywell.comAP: ha.ap.service@honeywell.comwww.honeywell.com© 2016 Life Safety DistributionGmbH. All rights reserved.This document containsproprietary information of LifeSafety Distribution GmbH and itsaffiliated companies and isprotected by copyright and otherinternational laws. Reproductionor improper use without specificwritten authorization of LifeSafety Distribution GmbH isstrictly forbidden.CHoneywell Analytics Inc.Lincolnshire. Made in USA

/ 2

Related manuals for Honeywell DX100 (M)