Honeywell 7845GSM Quick Manual

Also see for AlarmNet 7845GSM: Installation and setup guide Quick setup guide Installation guide

Honeywell 7845GSM Quick Manual Manual pdf 1 page image

7845GSM / 7845i-GSM QUICK GUIDEfor “C” Series Replacement and New InstallationsK14324V1 8/06 Rev. B Copyright 2006 Honeywell International Inc.165 Eileen Way, Syosset, New York 11791This guide explains how to install a 7845GSM or 7845iGSM for basic ECP mode applications primarilyintended to replace "C" series modules. This guide can also be used by experienced installers for new7845GSM/7845i-GSM installations. Abbreviated programming and registration procedures also provided.Programming assumes module's default valueswill be used. See Installation Guide for values.Connect 7720P to Module.Exit Program Mode by pressing "Shift -ESC," thenpress "N" at the Review prompt, then press"Shift -Y" at the "EXIT PROG MODE?" prompt.Go to "PRIMARY SUB ID" prompt and enter ID.(provided by CS)Go to "PRIMARY CS ID" prompt and enter ID.(provided by CS)Scroll (Using Up/Down Arrows) to "PRIMARYCITY ID" prompt and enter ID. (provided by CS)Enter Program Mode by pressing [ # ], then"Shift -Y" at the "START PROGRAM MODE"prompt.Go to "DEVICE MODE" prompt and confirmmodule is in "ECP" Device Mode. (Refer to theInstallation and Setup Guide if using any othermode.)Honeywell's AlarmNet DirectPROGRAMMING AND REGISTERING THE MODULE WITH THE 7720PA.B.C.D.E.F.G.For new 7845GSM/7845i-GSM:Register Module by pressingShift - [ ] Up Arrow key.Disconnect the 7720P and install modulecover (use cover securing screw for ULinstallations).Wait for the "Registration Success" messageto appear. The unit is registered and availablefor alarm reporting. Refer to the Installationand Setup Guide if any error messagesare displayed.A.B.You can also register the module by calling theAlarmNet Technical Assistance Center (TAC)at 1-800-222-6525.You will need the following information:· MAC number (found on the label).· Subscriber information (provided by thecentral station), including a city code,CSID, and a subscriber ID.When instructed to do so, triple-click thetamper switch to complete the registration.COMMAND FUNCTIONShift - [D]Shift - [C]Shift - [F]Shift - [X]Shift - [ ]Shift - [T]Shift - [S]Shift - [E]Shift - [B]Shift - [A] Software Revision (month, day, year)MAC Address, SCID, and IMEI DisplaysTime (GMT from AlarmNet network)Network Diagnostics Display (internet status)System Status (faults, battery, line voltage)GSM Status Display Screens (radio status)Network Diagnostic TestTest Alarm (for registered modules only)Reset the module(UP arrow) Registration for new installation(DN arrow) Registration with PIN for Replacement[ ][ENTER] Enter Program ModePROGRAMMER KEYBOARD COMMANDS("D" and "F" apply to 7845i-GSM only)NOTES: A. AlarmNet-I Account: The 7845GSM and 7845i-GSM modules require an AlarmNet–I account.For new installations, please obtain the account information from the central station prior to programmingthis module. For replacement installations, the AlarmNet-I account is created automatically when the moduleis registered (based on the existing "C" series account).B. For Replacement InstallationsCheck the existing device for its current mode and programming options prior to replacing.Do not use the existing “C” radio’s antenna. (AMPS antenna is not compatible with this module).·····By 7720P: See procedure below.By Phone (registration only): See below.Registering by Phone:RegisteringIf replacing a "C" series module:Register Replacement Module by pressing[ ] Down Arrow key, Then enterPIN Number (last four digits of old module'sMIN number) and press Enter.ORFor a replacement module, an alarm message(00D0 010B 0) will be sent to the central stationindicating the "C" series module has beenreplaced.C.By AlarmNet Direct Website: GO TO: https://services.alarmnet.com/AlarmNetDirect/userlogin.aspxLog in and follow the on-screen prompts. See "Honeywell's Alarmnet Direct" section on back.This product can now be programmed and registered through the Alarmnet Direct Website, which is a powerfulweb-based solution that provides our customers with a communication link to AlarmNet devices and services.To program and register the module via the website (if you are already signed up for this service),please go to: https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx.Log in and follow the on-screen prompts.For purposes of validation, please have the following information available when programming the module:1. Primary City ID (two-digit number)2. Primary Central Station ID (two-digit hexadecimal number)3. Primary Subscriber ID (four-digit number)4. MAC ID and MAC CRC number (located on outside of box and on label inside module)or Min Number of the device you’re replacing5. Mode of operation of existing radio if replacing a “C” series radio.Dealer Sign-UpIf you are not signed up for this service, click on “Dealer Sign-Up” from the login screen to gain access to ourweb-based programming of Honeywell's 7845GSM/7845i-GSM and next generation communication devices.Dealer Sign-Up Direct Link: https://services.alarmnet.com/AlarmNetDirectP_SignUp.You will be instructed how to proceed and a login will be created upon completing the sign-up form. Only onesign-up per dealer is required. Once an initial user is established, additional logins may be created by that user.NOTE: Central Stations sign up by contacting AlarmNet Administration at 800-222-6525 option 3.Programming and RegistrationProgramming(WHEN USING ECP MODE ONLY)

/ 2

Related manuals for Honeywell AlarmNet 7845GSM