Harman Kardon MAS 101 Owner's Manual

Also see for MAS 101: Service manual Service manual

Contents

Harman Kardon MAS 101 Owner's Manual Manual pdf 11 page image

MAS SYSTEM11OperationUsing the MAS system is simple and intuitive. The front-panel controls use advancedtouch-sensitive technology. To use the front panel, place a finger over any of the illuminatedicons. A gentle tap is all that is necessary. Wait a few seconds for the system to processeach command. To remove fingerprints, wipe the front panel with a dry microfiber cloth.Using the Remote ControlPoint the remote at the front of the MAS system. The remote IR sensor is located onthe right half of the front panel of the controller. Do not block the sensor. The remotehas a range of approximately 6m, up to 30 degrees off center. If the batteries requirereplacement, see Step 2 of the Installation section. Use caution and dispose of batteriesaccording to environmental requirements. Never throw the batteries into fire, and removethem from the remote if the remote will be unused for a long period of time.Turning on the MAS SystemTo turn on the MAS system, press and hold the Power button on the remote or the controllerfor 1 second. The system will also turn on when one of the Source Selectors, the Ejectbutton or the Play/Pause button on the remote is pressed.Press the Power button to turn off the system. If the clock has been turned off, themessage display will go dark to conserve power. Otherwise, the time will be displayedat half-brightness.Setting the ClockThe clock may be set using the Settings menu. See Figure 2.1. Press the Settings button on the remote.2. Press the 7/3 buttons until “Time Setup” appears in the message display.3. Press the Enter button to display “Clock.”Turn the clock on or off: Press the Enter button and use the 7/3 buttons to select “On”or “Off.” Turning the clock off conserves power when the system is powered down toStandby mode.4. Set the clock: Press the 7/3 buttons until “Set Clock” appears on the lower line. Pressthe Enter button to display “Set Time.”Set the time: Press the Enter button and use the numeric keys to enter the hour,tthen the minute. If the 12-hour time format is active, use the 7/3 buttons to select“AM” or “PM.” Press the Enter button to advance from one field to the next withoutchanging it, and press the Enter or Back button to save the settings.Set the format: Press thet 7/3 buttons until “Set 12/24 hour” appears. Press theEnter button to change the format, and use the 7/3 buttons to select betweenthe 12- and 24-hour time displays. Press the Enter or Back button to save thechange.5. Set the day of the week: Press the 7/3 buttons until “Set Day” appears. Press the Enterbutton to display the day of the week, and use the 7/3 buttons to select the desired day.Press the Enter or Back button to save the changes.Setting the AlarmsFor automatic turn-on at a programmed time, set one or both of the alarms. The alarmsmay be set using the Settings menu. See Figure 3 on page 12.1. Press the Settings button on the remote.2. Press the 7/3 buttons until “Alarm Setup” appears in the message display.S e t t i n g sS p e a k e r S e t u pRightEnter BackEnter BackEnter Enter or BackLeftRightLeftRightLeft> S e t t i n g sT i m e S e t u p ><<<T i m e S e t u pS e t C l o c k > T i m e S e t u pS e t D a y>T i m e S e t u pC l o c kC l o c kO f f S e t D a yM o n d a y >>S e t C l o c kS e t 1 2 / 2 4 h o u r >S e t 1 2 / 2 4 h o u r1 2 h o u r >S e t C l o c kS e t T i m e >S e t T i m e1 2 : 4 3 >RightLeftEnter Enter or BackEnter Enter or BackEnter Enter or BackFigure 2: Setting the Clock