Harman AMX MT-2002 Quick Start Manual

Harman AMX MT-2002 Quick Start Manual Manual pdf 2 page image

Wiring a Power ConnectionTo use the 2-pin 3.5 mm captive wire connector with a 12V ... -compliant powersupply, the incoming PWR and GND wires from the external source must beconnected to their corresponding locations on the connector (FIG. 5).The connector uses locking screws to insure a connection to the device, somake sure to insert and tighten the screws before applying power.PWR +Power SupplyTo the Touch PanelGND -FIG. 5 NETLINX POWER CONNECTOR WIRING DIAGRAM1. Insert the PWR and GND wires on the terminal end of the 2-pin 3.5 mmcaptive wire cable.Match the wiring locations of the +/- on both the power supply and theterminal connector.2. Tighten the clamp to secure the two wires. Do not tighten the screwsexcessively; doing so may strip the threads and damage the connector.3. Verify the connection of the 2-pin 3.5 mm captive wire to the external12V ... -compliant power supply and apply power.Powering On/Off Modero G5 PanelsModero G5 touch panels may be powered on by touching and holding theSleep button. To power off the panel, press and hold the Sleep button, andselect Power Off on the on-screen menu (FIG. 6):FIG. 6 SLEEP BUTTON - PRESS AND HOLD TO ACCESS POWER OFF/SETTINGS OPTIONSConfiguration and ProgrammingModero G5 touch panels are equipped with a Settings menu that provides theability to configure various features on the panels. To access the Settings menu,press and hold the Sleep button, and select Settings.Note: Information on the Settings menu, panel configuration, and programmingis provided in the Modero G5 Programming Guide, available at www.amx.com.Setting the Panel’s Device Number and Device Name1. In the Settings menu, select NetLinx. This opens a password keypad.2. Enter the panel password into the keypad (the default is 1988) and selectOK to access the NetLinx page.3. Press Device Number to open the NetLinx editing window.4. Enter a unique Device Number assignment for the panel and press OK.5. Enter a unique Device Name assignment for the panel and press OK.Configuring the Panel’s IP AddressThe first step is to configure the panel’s IP address. Note that this only configuresthe panel to communicate with a network; it is still necessary to connect to theNetLinx Master (see Connecting to a NetLinx Master below).Network Communication via DHCP1. In the Ethernet page, press DHCP/Static field to open the DHCP/Staticwindow. Note that DHCP is the default setting.2. Select Host Name, enter the new host name3. Press OK to save changes.Network Communication via Static Address1. In the Ethernet page, press DHCP/Static to open the DHCP/Static window.2. Select Static to open the Static IP window.3. Press any field to open a keypad or keyboard (depending on the field), andenter the appropriate network address information.4. Press OK to save your changes and return to the Ethernet page.Connecting to a NetLinx MasterTo establish the type of connection to make between the panel and theNetLinx Master:1. In the NetLinx page, press Mode to choose the connection mode (URL,Listen or Auto):CONNECTION MODESMode Description ProceduresURL The device connects to the targetMaster’s IP address via a TCPconnection.1. Select URL in the Mode menu.2. Enter the Master IP/URL, Master Port Number, andUsername/Password (if required by the Master).3. Press OK to save changes.Listen This mode allows the panelto“listen” for the Master’scommunication signals.Note that in this mode, the SystemNumber and Master IP/URL fieldsare read-only.1. Select Listen in the Mode menu.2. Confirm the panel’s IP address is on the Master’sURL list (via NetLinx Studio).3. Press OK to save changes.Note: The Host Name (set on the Ethernet page), canbe used to locate the panel on the Master (particularlyuseful for DHCP connections where the IP addresscan change).Auto Use this mode when both thepanel and the NetLinx Master areon the same Subnet.1. Select Auto in the Mode menu.2. Enter the System Number and Username andPassword (if applicable).3. Press OK to save changes.2. If password security is enabled on the target Master, enter the Usernameand Password:a. Select Username to open the NetLinx window.b. Enter the Username and Password required by the Master.c. Press OK to save changes and return to the NetLinx page.Related Software and Additional Documentation(at www.amx.com)• Programming the Modero G5 touch panel requires the use of either RapidProject Maker (RPM) or the latest version of Netlinx Studio and TPDesign5,both available to download at www.amx.com. Refer to the NetLinx Studioand TPDesign5 online help for information.• For information on designing touch panel pages intended to optimize theModero G5 experience, refer to the G5 Considerations Guide.• For additional information on the MT-2002 panel, refer to the Modero G5Touch Panel Instruction Manual.• For detailed information on the Settings menu as well programminginformation and instructions on upgrading firmware, refer to the Modero G5Programming Guide.• Detailed specifications drawings for the MT-2002 are available to downloadfrom www.amx.com.© 2019 Harman. All rights reserved. Modero X and Modero X Series, AMX, AV FOR AN IT WORLD, and HARMAN, and their respective logos areregistered trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarksof their respective companies. AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specificationswithout prior notice at any time. The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153AMX (UK) LTD, AMX by HARMAN - Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/ LAST REVISED: 05/01/2019

/ 2

Related manuals for Harman AMX MT-2002