Menu
HandyHeat DVTH132 A Owner's Manual
   | |
-MaterialOne (1) PB130 -230 po wer baseOne (1) floor sensor (for floor h eating control mod ules AFand F )One (1) wall plate (optional, in cert ain countries)Power BasePB130-230Installation InstructionsTechnical SpecificationsModel : PB1 30-23 0Supply : 23 0 VAC , 50 HzLo ad : 16 A maxi mum (resistive onl y)Power : 3680 W atts (NI) @ 230 VACC erti fica tio n: E N607 30-2-9 / EN5 008 1-1 / EN50 082-2St orage: -20°C to 50°CProtect ion : C lass 2Pr otec tion de gree: I P 20Automatic action : Type 1. BEnvironment : Normally pollutedSize (H • W • D) : 75 x 75 x 14 mm (7 .5 x 7.5 x 1.4 cm)NO TE: T he termin als are designed to handle a wire sizebetween 0 .33 to 3.1 mm2.TWO (2) YEAR LIMITED WARRANTYThis produ ct is guaranteed ag ainst workmanship defects for a two -year period followingthe ini tial date o f purchase. During this period, HandyHeat . will re pair orreplace, a t our option and without char ge, any def ective p roduct which has been us edunder normal conditions.The warranty does not cover delivery co sts and do es n ot apply to products po orlyinstalled o r randomly damaged f ollowing i nstalla tion. This warranty cancels andreplaces any ot her manu facturer's e xpress or implied warranty as well as any othercompany c ommitment.HandyHeat cannot be held liable for related or rand om dama ges f ollowingthe installation of th is prod uct. The defective p roduct as well as t he p urchase invoicemust be r eturned to the p lace o f purchase or ma iled, prepaid and insure d, to thenea rest locat ion.If you have any question s concerning the inst allation of thePB130-230 power base , call our techn ical support team at:IntroductionT he PB130-230 power base is designed to power aDVTH13xSeries con trol mo dule. The resistive load must not exceed3680 watts (NI) @ 230 VAC (16 A).Installation GuidelinesT u rn off power to the heating system at the main power pa ne lto avoid e le c trical shoc k. Installa tion s h o u ld be ca r rie d out bya n elec tr ic ia n.All work must conform to the most recent country’ s regu la-tions for electrical inst allations an d wiring.Th is thermost at should be connected on a circuit equ ippedwith a fuse or a circuit breaker . It must be installed on a certi-fied el ectrical box.Fo r a new inst alla tion, choo se a lo ca tion about 1.5 m (5 ft.)above the floor.The thermost at must be installed facing the heating system.T he thermostat must be installed on an inside wall.Avoid locations where there are air dra fts (top of stairca se, airoutlet), dead air spo ts (b ehind a door), d irect sunl ight or con-cealed chimne ys or stove pipe s.Remove the scre w holding the con-trol module to the power base.Note that the scre w can not becompletely re moved.If yo u have a wall plate : Before makingthe co nnections, make sure that the basecovers t he ele ctrical bo x entirely. If n ot,inse rt the cover pl ate on rear of the base.NOTE: T he cover plate can be us ed to coverthe pla te for aesthetics.Connect the wires:• Power :Terminals 1 and 5• Lo ad :Terminals 2 and 4• F loo r sensor :Terminals 6 and 7(no pola rity needsto be respected )Do n ot pla ce the floor sensordirectly next to an element butrather, for maximumperformance, the floor sensor sh ould be ce ntered be tween the wire sin the mat (80°C max.). The tem pera ture sensor wire ca nnot la yacross any heater wires.If the lo ad is driven thro ugh acontactor, a snubber must be installedat the con tactor’s co il termina l. Seewiring dia gram below.Push wires into th e electrical box an d securethe base to the electrical box anchora ge.Th e head of the screw must be lessthan 2mm th ick.Con figure the switches (if neces-sary) a nd install the co ntrol mod-ule o nto the p ower base (r efer tothe user gu ide).Return power to the heating system .DVK-130-001-AInstallation and WiringNdr. Fabriksvej 5DK-8722 HedenstedDenmarkTel. +45 7675 8030Fax +45 7675 8032Email: info@dansk-varmekabel.dkwww.handy-heat.com |
Related manuals for HandyHeat DVTH132 A
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved