Haier XQS50-28 User Manual

Contents

Haier XQS50-28 User Manual Manual pdf 3 page image

The ventilationholes at thebottomBefore UsingBefore UsingSafety precautionsIn case the washing machine is installed on groundwith carpet, be careful not to block the ventilation holewith carpet.Do not put the machine at damp place like thebathroom. Never wash it with water. Do notput wet laundries on the control panel coating .Do not let the machine share one receptacle with otherelectric appliances. If the power plug is damaged, orthe plugging into the receptacle is loose, do not usethe plug any more.Do not wash water-proof laundry like the raincoat,bikecovers, down textiles etc. To avoid abnormalvibrations in spinning and damages to the laundries.Do not bend, stretch, twist, bind the power cord by force, or reformit.Do not press or clamp it with heavy items. If the power cord and powerplug are bad, or the receptacle is loose, be sure to have it replaced bythe technicians of our special shop or our agent,or the after-sales servicedepartment to avoid any risk.Keep the prong of the power plug clean.Ifdust is found on the power plug, please wipe it off with dry cloth.In normal usage of the washing machine, the powerplug shall be ready to be pulled or plugged with hang.Be sure to pull the plug off and close the water faucetwhen occurring power failure,delivering the maching,setting the machine idle or cleaning the machine,Donot plug or pull the power plug with wet hand.earthDo not use water with temperature higher than 50Please plug the plug on special 220V AC receptacle.Be sure to use three phase power receptacle.Ensurethe earthing prong of the power redeptacle is earth-ed reliably.Use leakage protector if possible.The digitron displays E0.The safety switch acts, and thespinning cannot work. Thedigitron displays E3.The water filling does not work, or isslow. After about 15 minutes later,the digital displays E4.The drainage cannot work, or is too slow.The digitron displays E1.It stops running in midway. The digitrondisplays E2.The power voltage is too low.The top lid is not closed.The top lid is opened during reserveprocedure.Close the top lid.Close the top lid.Is the drain hose put down?Is the drain hose blocked?Put down the drain hose. Open and close thetop lid once.Clean the foreign material. Open and closeThe top Lid Once.Are the laundries put slantingly?Is the machine slanting?Reorder the laundries. Close the top lid.The machine will start running after 10seconds of being placed horizontally.Is the water tap opened, or is there watersupply failure?Is the water inlet valve blocked?Is the water pressure too low?Open the water tap. Push the start/Pausebutton once.Clean the water inlet valve then pushthe start/Pausebutton once.Push the sStart/Pause button once.The water level sensor is bad. Please contact the after-salesservice department.Is the machine slanting?Are the laundries put slantingly in spinning?Are there any foreign materials?Is the screw of the jointer of waterinlet hose loose or awry?Pull off the power plug. Wait for thevoltage resuming normal before usage.Adjust the machine to be evenReorder the laundries and close the top lid.Remove the foreign materials.Fasten the screw of the jointer properly.The water tap leaksThe digitron displays E8.The digitron displays E6.There's abnormal soundinside the machinePhenomenan The reason How to settleTrouble-shooting Answer to question(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdownssometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the specialmaintenance department or after-sale service department of our company. Do not repair it by yourself.The digitron displays E9. The power voltage is too high.The machine doesnot actNot washNot spinIs there power failure?Is the power plug inserted tightly?Is the water level reached preset position?Please use it when there's power supply.Insert the power plug tightly.Fill water to the preset position.Is the power plug inserted tightly?Is the top lid closed reliably?Are the laundries set flat?Insert the power plug tightly.Close the top lid.Set the laundries flat.Common phenomenaPhenomena Explanation* The spinning is intermittent when it starts. * Balance the laundries to avoid slanting.* The wash proced ure pauses. * The cloth sensor is detecting the cloth. It will startadding water after about 48 seconds.* Select “ Spin” program, but it doesn’t work. * The program is setting the drain time. A certainperiod is needed before it starts spinning.* The pusaltor pauses during washing, rinsingor adding water.* It is to avoid splashing during water filling.* There may be some water flowing out of thedrain hose in the first use of the machine.* It is the water remained in the performanceinspection by the factory.