HP 4x SpeedCD–ROM Disk DriveUser’s GuideWorkstation Systems GroupOrder No. A1658–90669Edition E0895Printed in U.S.A.

revision history

documentation conventions

preparing for installation

general description

maintenance and troubleshooting

troubleshooting

removal and replacement procedures

warnings and cautions

HP A165890669 User Manual

safety and regulatory statements

installation notice

preparing the system

powering off the workstation and any peripherals

emissions regulations

emissions regulations compliance

scsi connector pinouts

705 Workstation

legal notices

about this manual

how to use this guide

typographic conventions

Installing SCR

Using SCR

Conﬁguring SCR

Setting the Data Collection Schedule

Collecting Conﬁguration Data On Demand

Checking Data Collection Status

Viewing Conﬁguration Information on a Node

Tracking Conﬁguration Changes with SCR

Checking Node Differences

Using Tags to Simplify Node Management

Using Filters

Simple Filter Example

Standard Filters

Using the Probe Filter

Additional Uses of SCR

Change Management

Disaster Recovery

SCR Reference (man Pages)

scrdelete (1M)

scrdiff (1M)

scrhist (1M)

scrstatus (1M)

scrtag (1M)

scrupdate (1M)

scrviewer (1M)

scrlog_viewer (1M)

General Description

Major Features of DDS Drives

DDS-2 Drive

DDS-2 Drive Physical Specifications

Preparing to Install the DDS-2 Drive

Setting the SCSI-2 Address

Address Jumpers

Rear View of DDS-2 Drive and SCSI Address/Jumper Settings

Switch Settings for Data Compression Operation Mode

Preparing the System

SCSI-2 Connection and Termination

Powering Off the Workstation and any Peripherals

Adding or Removing the DDS-2 Drive Bezels or Expansion Brackets

Removing a Bezel from the DDS-2 Drive

Your DDS-2 Drive Configuration

LEDs

Cleaning the Tape Heads

Using the DDS-2 Drive

Verifying the DDS-2 Tape Drive Operation

Media Interchangeability Restrictions

Ordering Information

Troubleshooting

Checking the Address Settings for Single-Ended Drives

Checking the Hardware Installation

Rechecking the Address Settings

Removal/Replacement Procedures

Removing and Replacing the DDS-2 Drive

Adding a Bezel to the DDS-2 Drive

Adding or Removing Expansion Brackets

related manuals

DDS-DC Drive Environmental Requirements

DDS-DC Drive Physical Specifications

Tools Required

Rear View of DDS-DC Drive and SCSI Address/Jumper Settings

Powering Off the Workstation and Any Peripherals

Adding or Removing the DDS-DC Drive Bezels or Expansion Brackets

Removing a Bezel from the DDS-DC Drive

Your DDS-DC Drive Configuration

Setting the Write-Protect Tab on a DDS Tape

Using the DDS-DC Drive

Verifying the DDS-DC Tape Drive Operation

Preparing to Install the DDS-DC Drive

Adding a Bezel to the DDS-DC Drive

A–1. SCSI Connector Pinouts

A165890669

A4325-60001

Model 710 - Workstation

Model 712/100 - Workstation

Model 712/60 - Workstation

Model 712/80 - Workstation

Model 715/100 - Workstation

Model 715/100XC - Workstation

Model 715/33 - Workstation

Model 715/50 - Workstation

Model 715/64 - Workstation

Model 715/75 - Workstation

Model 715/80 - Workstation

Model 720 - Workstation

Model 725/100 - Workstation

Model 725/50 - Workstation

Model 725/75 - Workstation

Model 730 - Workstation

Model 735cL - Workstation

Model 755/125cL - Workstation

Model 755cL - Workstation

HP A165890669 User Manual

Product

Learn More

Legal


Contents revision history documentation conventions preparing for installation general description maintenance and troubleshooting troubleshooting removal and replacement procedures warnings and cautions	HP 4x SpeedCD–ROM Disk DriveUser’s GuideWorkstation Systems GroupOrder No. A1658–90669Edition E0895Printed in U.S.A. Next / 61