HAMPTON BAY HD28906 Use And Care Manual

HAMPTON BAY HD28906 Use And Care Manual Manual pdf 1 page image

Item #1001 492 705Model #HD28906Use and Care GuideLOW VOLTAGE PATHLIGHT AND FLOODLIGHT KITPart Description QuantityA Lens cover 2B Lens 2C 20W Halogen MR11 Bulb 2D Body 2E Adjustment screw 2F Post 2G Connector 2H Spike 2I Top Cover 6J 10W Halogen T3 Bulb 6K Bulb socket 6L Post 6M Connector 6N Spike 6O 120W Transformer 1P Wire AWG14 SPT2W 75’ 1Q Plastic anchors 2R Screws 2PACKAGE CONTENTSAssembly and Installation1 Attaching and installing the floodlight2 Attaching and installing the pathlightWARNING: Never push the fixture into the ground by the lamp body (D) or use ahammer to insert the spike (H) into the ground.WARNING: Never push the fixture into the ground by the lens cover (I) or use ahammer to insert the spike (N) into the ground.CAUTION: Safe for outdoor operationWARNING: To reduce the risk of FIRE OR INJURY TO PERSONS:WARNING: Turn off/unplug and allow to cool before replacing lamp.WARNING: Lamp gets HOT quickly! Contact only switch/plug when turning on.Do not touch hot lens, guard or enclosure.WARNING: Keep the lamp away from materials that may burn.WARNING: Do not touch the lamp at any time. Use a soft cloth. Oil from skin maydamage the lamp.WARNING: Do not operate the luminaire fitting with a missing or damaged lensor bulb protector.□ Carefully remove the fixture from its protective packaging.□ Run the wire through the notch in the top of the spike (H) and attachthe spike to the post (F) by turning clockwise.□ Loosen the set screw (1) and slide off the light cap (A).□ Remove the lens cover (B) by turning counterclockwise.□ Do not remove the lens from the lens cover.□ Insert the bulb (C) into the bulb socket.Use a soft cloth, as oil from skin maydamage the lamp bulb.□ Replace the lens cover (B) and the light cap(A) over the body (D). Adjust the light’s beamby sliding the cap back and forth (back = widebeam, front = narrow beam) and screw the setscrew (1) in place once the proper light beamis found.□ Attach the body (D) and the post (F) using theadjustment screw (E) and rotating clockwise.□ Adjust the fixture’s angle by loosening theadjustment screw (E) and retightening it.□ Ensure the lens points up and never towardsthe ground.□ Carefully remove the fixture from its protective packaging.□ Pass the wire through the notch in the top of the spike (N) andattach the spike and post (L) by pressing them together.□ Insert the bulb (J) into the bulb socket (K). Use a soft cloth, as oilfrom skin may damage the lamp bulb.□ Attach the cover (I) and the post (L) together by turning clockwise.WARNING: Install in accordance with all local codes and ordinances.Only for use with low voltage power units with a maximum output rating of 15V,300W per secondary.FOR LANDSCAPE LIGHTING SYSTEMS ONLY. OUTDOOR USE ONLY. THE DEVICE ISACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THESUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCALINSPECTION AUTHORITIES HAVING JURISDICTION.PATHLIGHT UL LISTED UNDER MODEL # U201159SPOTLIGHT UL LISTED UNDER MODEL # U201167Please read and save these instructionsINSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONSIMPORTANT SAFETY INSTRUCTIONSLighted lamp is HOT!OPQR3 Connecting the wiresWARNING: The wire connector (G) & (M) contacts have sharp edges for piercingthe main low voltage cable. To avoid injury, do not touch the metal contacts.CAUTION: The wire from the low voltage power unit shall be 12-16 AWG typeunderground low Energy Circuit Cable or SPT2W.IMPORTANT:• Protect the wiring by routing it in close proximity to the light fitting, or next to abuilding structure such as a house or deck.• The landscape wire and connector can also be hidden under stone or buriedunder grass at a maximum depth of 6” (15.24 cm).• Do not submerge fixture in water.WARNING: Risk of Electric Shock. Install all luminaires 10 ft. (3.05 m) or morefrom a pool, spa or fountain.ABCDFEGHIJKLNMAB 1CDFEHGREA S E!IJKLNMIMPORTANT: We recommend to apply petroleum grease (not included) around thepost threading when replacing the head after you change the light bulb. Do notovertighten the head onto the post.