HAKO FX-8804 Instruction Manual

HAKO FX-8804 Instruction Manual Manual pdf 1 page image

HAKKO FX-8804 1Caution label 1Copyright © 2012 HAKKO Corporation. All Rights Reserved.HAKKO FX-8804 can not be operated by itself. Read the instruction manual for theHAKKO FX-888D soldering station used in conjunction with the HAKKO FX-8804.Do not set the temperature 400℃(752℉) or more.3. COMPATIBLE STATIONS 5. ASSEMBLY6. OPERATIONInstruction ManualSMD HOT TWEEZERHeat resistant pad 1Instruction manual 11. Put the caution label on the HAKKO FX-888Dsoldering station.The HAKKO FX-8804 can not be used attemperature above 400℃(752℉). If settingthe temperature over 400℃(752℉), the stationwill result in accidents or damage.2. Attach the heat resistant pad.Pass the iron cord through the hole in theheat resistant pad. Use it when removing the tips.Iron holderIf you use the iron holder for FH-800 included with HAKKO FX-888D,remove the iron receptacle and insert the holder clip (not included) as the figure below indicates.B. Turn on the power switchPower consumptionTemperature rangeTip to ground resistanceTip to ground potentialLength of cordLength (w/o cord)Weight (w/o cord)C. CalibrationNever set the temperature to any valueover 400℃(752℉). Doing so may damage the station.Set the temperature depending on the typeof work to be done.Refer to the HAKKO FX-888D instruction manualfor setting the temperature.2. Apply solder or flux.If there is not enough solder on the P.W.B.or the soldered area is too small,apply the solder or flux to the P.W.B.Solder wets to the tip.3. Melt the solderPlace the tip on the soldered part andmelt the solder. Confirm the solder is fullymelted. (Fig.1)4. Remove the component.After confirming that the solder is fully melted,hold the tweezer lightly to lift thecomponent, and remove it. (Fig. 2)Removing components(Fig.1)Solder(Fig. 2)Replacing the tipThe tip may be hot. Avoid holding the hot tip for a long time even if using theheat resistant pad. Otherwise burns may result.1. Turn the nipple counterclockwise and loosen it.Do not remove the nipple.2. Insert the new tip into the HAKKO FX-8804.When the tips click, they are fully inserted.Using the holder clip, attach the tip parallelto other tip.3. Tighten the nipple firmly, fix the tip.HAKKO FX-8804Caution labelHeat resistant padHandleHolder clip1. Temperature settingTip for Chip Tip for SOPThank you for purchasing the HAKKO FX-8804 SMD Hot TweezerPlease read this manual before operating the HAKKO FX-8804.Keep this manual readily accessible for reference.1. PACKING LIST AND PART NAMES Please make sure that all items listedbelow are included in the package.Tip(Chip 2L)2. SPECIFICATIONSUse the HAKKO FX-8804 with the HAKKOFX-888/888D soldering station.AC 26V 65W200 400℃ (400~752℉)<2Ω<2 mV1.2 m (47.2in.)186 mm (7.3in)93 g (0.21lb.)※Specifications and design are subject to change without notice.※This product is protected against electrostatic discharge.This product includes such features as electrically conductive plastic parts and grounding of the unitas measures to protect the device to be soldered from the effects of static electricity. Be sure to observethe following instructions:1. The plastic parts are not insulators, they are conductors. When making repairs or replacingparts, take sufficient care not to expose live electrical parts or damage insulation materials.2. Be sure to ground the unit during use.WARNING4. WARNINGS, CAUTIONS, NOTES AND EXAMPLESCAUTIONDo not touch the tip or metal parts near the tipDo not allow the tip to come close to, or touch, flammable materials.Inform others in the area that the unit is hot and should not be touched.Turn the power off when not in use, or left unattended.Turn the power off when changing parts or storing the HAKKO FX-8804.This appliance is not intended for use by persons (including children) with reduced physical,sensory or mental capabilities, or lack of experience and knowledge, unless they have beengiven supervision or instruction concerning use of the appliance by a person responsible for their safety.Children should be supervised to ensure that they do not play with the appliance.Do not use the HAKKO FX-8804 for applications other than desoldering.When you use the HAKKO FX-8804 for the first time, note that calibration is recommended.Do not set the temperature above 400℃ (752℉).Do not strike the iron against hard objects to remove excess solder. This will damage the iron.Do not modify the HAKKO FX-8804.Use only genuine HAKKO replacement parts.Do not allow the HAKKO FX-8804 to become wet, or use it when hands are wet.Remove power and iron cords by holding the plug - not the wires.Since smoke is produced when using the HAKKO FX-8804, be sure the work area is well ventilated.While using HAKKO FX-8804, do not do anything which may cause bodily harm or physical damage.When power is ON, tip temperature will be between 200℃ and 400℃ (400 to 752℉).To avoid injury or damage to personnel and items in the work area, observe the following :NOTE :Turn on the power for HAKKO FX-888D soldering station.The heater lamp flashes as the tip comes up to the set temperature.The unit is now ready to perform soldering work.Place the HAKKO FX-8804 in the iron holder when not in use.Turn the power off when not using the station for a long time.Before using the HAKKO FX-8804, be sure to calibrate the station.(Refer to the HAKKO FX-888D instruction manual.)Use HAKKO FG-100 Thermometer or HAKKO FG-101Soldering Tester to measure the tip temperature.When calibrating the tip, place the edge of the tip onthe measuring point of the HAKKO FG-100 or FG-101.NOTE :Dial type label onlyPut the label above the temperatureindicator lines.Put the label in a visible area such asthe front or top panel of the station.Very high tip temperature may damagethe P.W.B., possibly causing the printedpattern to become detached.Recommend setting the temperaturedepending on work conditions.Setting the lowest possible effectivetemperature helps protect parts thatare sensitive to heat and extends tiplife.Never force the component or squeeze with excessiveforce as this may damage the work and/or tips.Do not operate this stationover 400℃(752℉) withFX-8804 SMD HOT TWEEZER.Do not operate this stationover 400℃(752℉) withFX-8804 SMD HOT TWEEZER.2012.10MA02040XZ121001A. ConnectionBe sure to turn off the power before connectingor disconnecting the cord assembly forthe iron to and from the receptacle to avoiddamaging the unit.1. Connect the cord assembly of HAKKO FX-8804to the receptacle of HAKKO FX-888D.2. Place the iron into the iron holder.3. Plug the power cord into the power supply.receptacleTo disconnect, hold the plug.Push on the pluguntil it stops,making sureit is securelyconnected.

/ 2

Related manuals for HAKO FX-8804