Menu
HAKARU PLUS TFL-B101Q Manual
                    |
HAKARU PLUS CORPORATION Tel. 81-6-6300-219505/12/16 TFL-B101Q DS (FL6)Page 1Smart mono-color digital bargraphwith four fully programmable set points formonitoring, measurement, and control applications.HAKARU PLUS CORPORATION• Two 10 Amp Form C, and two 5 Amp Form A relays available• Auto-sensing AC/DC power supply. For voltages between85-265 V AC / 95-370 V DC (PS1) or 15-48 V AC / 10-72 V DC (PS2).• Optional isolated 16 bit analog output. User or factoryscalable to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across anydesired span from ± one bar to the full scale range• Provision to connect an external programming lockout switch.• Optional NEMA-4 front cover.• 24 V DC excitation is available to power external 4/20 mAtransmitters and 5 or 10 V DC excitation is available forresistance bridge type sensors.• The two 101 segment bargraph can be independently scaled.• Bargraph center zero function.• Four programmable setpoints.• Relays activation can be selected to occur above (HI) or below(LO) each setpoint.• Decimal point setting.Input Specs: ..............Depends on range and function selectedA/D Converter: ..........14 bit single slopeAccuracy: ..................±(0.1% of reading + 1segment)Temp. Coeff.: .............100 ppm/°C (Typical)Warm up time:...........2 minutesConversion Rate: ......10 conversions per second (Typical)Bargraph Display: .....101 segment 4” vertical (std),horizontal (optn), red (std), green (optn),one red one green (optn)Polarity: .....................Selectable center zeroPositive Overrange: ..Bargraph display flashesNegative Overrange: First segment of bargraph display flashesRelay Output: ............Two 5 Amp Form A relays and Two10 Amp Form C relaysAnalog Output: ..........Isolated 16 bit user scalable mA or VOIC (mA out) ...........4-20 mA @ 0 to 500Ω max loop resistanceOIV (volts out) .......... 0-10 V DC @ 500 Ω or higher resistancePower Supply: ...........AC/DC Auto sensing wide range supplyPS1 (std).................85-265 VAC / 95-370 VDC @ 2.5W max 4.2WPS2 .........................15-48 VAC / 10-72 VDC @ 2.5W max 4.2WOperating Temp.: ......0 to 60°CStorage Temp:...........–20°C to 70°CRelative Humidity: ....95% (non condensing)Case Dimensions: .....3/32 DIN, Bezel: 36x144 mm(1.42”x5.69”)Depth behind bezel: (4.64") 117.5 mmPlus 10 mm (0.39”) for Right-angledconnector, or plus 18.3 mm (0.72”) forStraight-thru connector, or plus 26.5 mm(1.05”) for Push-On connector.Weight: .......................9.5 oz., 12 oz when packedGeneral FeaturesInput Module CompatibilitySpecificationsIndexSoftware FeaturesCenter Barfor Dual ScaleApplications(Tri-Color orMono-Color)Left or Right Bar to match 6” EdgewiseMechanical Meters with Left or RightPointers (Mono-Color only)TFL-B101QOMI 220 Bargraph Meter101 Segment LEDsin a 9/64 DIN CASEMore than 50 different Plug-in I-Series Input SignalConditioners are approved for OMI 220 Family meters. Someexamples are shown on pages 12 - 15. Check with your localdistributors for an up to date listing.Analog Scaling and Calibration 9Case Dimensions 15Center Zero Mode Scaling for Bipolar Inputs 6-7Component Layout 11Connector Pinouts 10Connectors 11Controls and Indicators 2Glossary of Programming Symbols and Modes ofOperation 2Custom Scales 19Functional Diagram 10General Features 1Input Module Analog Calibration Procedures 17Input Module Compatibility 1Input Module Component Glossary 16I-Series Input Signal Conditioning Modules 12-15OMI 220 Family Bargraphs and Meters 17One Point Quickset Rescaling and Calibration Procedure6Ordering Information 20Opening the Case to Access Mode Select Headers 4Overview of Display Modes, Scaling Capabilities andOperation Modes 3Panel Adapter 3Pin Descriptions 10Setpoint Adjust 7-8Setting the Colors 8Software Features 1Specifications 1Standard Display Mode Calibration Procedure 5Space 18Two Point Quickset Scaling and Calibration 5,6 |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved