GE iTwinkle Pre-Lit Tree Quick Manual

TM Pre-Lit TreeIMPORTANT SAFETY INSTRUCTIONS50 LED G35 lights with 450 Constant ON mini lights iTwinkle light showItem Number: 00684 / 00684D UL String Model Nos.: NHI-G35-50,CFPS(I)-100/2F(0.6), CFPS(I)-50(0.3) When using electrical products, basicprecautions should always be followed including the following:READ AND FOLLOW ALL SAFETYINSTRUCTIONS• This is an electrical product - not a toy! To avoid the risk of fire, burns, personalinjury and electric shock it should not be played with or placed where smallchildren can reach it.• Do not use seasonal products outdoors unless marked suitable for indoor andoutdoor use. When products are used in outdoor applications, connect theproduct to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is notprovided contact a qualified electrician for proper installation.• This seasonal use product is not intended for permanent installation or use.• Do not mount or place near gas or electric heaters, fireplaces, candles orother similar sources of heat.• Do not secure the wiring of the product with staples or nails, or place on sharphooks or nails.• Do not let lamps rest on the supply cord or on any wire.• Unplug the product when leaving the house, when retiring for the night, or ifleft unattended.• Do not use this product for other than its intended use.• Do not hang ornaments or other objects from cord, wire, or light string.• Do not place lighting string on carpeting, drapes, furniture or allow it to contactvinyl siding while the power is on.• Do not perform any maintenance or troubleshoot for bad/broken lamps whilethe power is on.• Do not close doors or windows on the product or extension cord as this maydamage the wire insulation.• Do not cover the product with cloth, paper or any material not part of theproduct when in use.• This product has a polarized plug (one blade is wider than the other) as afeature to reduce the risk of electric shock. This plug will fit in a polarized outletonly one way. If the plug does not fit fully in the outlet, reverse the plug. If it stilldoes not fit, contact a qualified electrician. Do not use with an extension cordunless plug can be fully inserted. Do not alter or replace the plug.• This product is equipped with push-in type lamps. Do not twist lamps• This product employs overload protection (fuse). A blown fuse indicates anoverload or short-circuit situation. If the fuse blows, unplug the product fromthe outlet. Also, unplug any additional strings or products that may beattached to the product. Replace the fuse as per the User Servicinginstructions (follow product marking for proper fuse rating) and check theproduct. If the replacement fuse blows, a short-circuit may be present and theproduct should be discarded.• Read and follow all instructions that are on the product or provided with theproduct.SAVE THESE INSTRUCTIONSUSE AND CARE INSTRUCTIONS• When the product is placed on a live tree, the tree should be well maintainedand fresh. Do not place on live trees in which the needles are brown or breakoff easily. Keep the tree holder filled with water.USE AND CARE INSTRUCTIONS (Continued)• If the product is placed on a tree, the tree should be well secured and stable.• Before using, or reusing, inspect product carefully. Discard any products thathave cut, damaged or frayed wire insulation or cords, cracks in thelampholders or enclosures, loose connections, or exposed copper wire.• When storing the product, carefully remove the product from wherever it isplaced, including trees, branches, or bushes, to avoid any undue strain orstress on the product conductors, connections and wires.• When not in use, store neatly in a cool, dry location protected from sunlight.USER SERVICING INSTRUCTIONSString Set Fuse Replacement:a) Before changing fuses, make sure the set is unplugged.b) Grasp plug and remove from the receptacle or otheroutlet device. Do not unplug by pulling on cord.c) Using a flathead screwdriver, open fuse cover. Slideopen the fuse access cover on top of attachment plugtowards blades.d) Remove fuses carefully.e) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).f) Close fuse cover. Slide closed the fuse access cover on top of attachmentplug. Make sure door is fully closed and fuses are completely covered.g) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse)that should not be removed. Discard product if the attachment plug isdamaged.Short and Long Extension Cord Fuse Replacement:Replace the fuse.a) Grasp the plug and remove from the receptacle orother outlet device. Do not unplug by pulling on cord.b) Using a flathead screwdriver, open fuse cover. Slideopen the fuse access cover on top of attachment plugtowards blades.c) Remove fuses carefully.d) Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse for the shortextension cord (provided with product). For long extension cord replace fuseonly with 7 Amp, 125 Volt fuse (provided with product).e) Close fuse cover. Slide closed the fuse access cover on top of attachmentplug. Make sure door is fully closed and fuses are completely covered.f) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse)that should not be removed. Discard product if the attachment plug isdamaged.Install Class 2 Power Supply To String:NOTE: Use only this GE branded, Class 2 Power Supply,Model SA3A-050-3000, manufactured by TDC that was providedwith this product. DO NOT use this adapter with any other product.Fig. 1 Fig. 2 Fig 31. Remove the Power Supply from its packing box.2. The LED string is fitted with a 2-pronged fitting.3. Align the notch in fitting with the inner tab on end of Power Supply {Fig. 1}4. Fully insert the fitting into the Power Supply {Fig. 2}5. Screw the collar completely onto the Power Supply turning clockwise {Fig. 3}WARNING:• This string contains two different types of Replaceable bulbs - steady-illuminating and fuse. REPLACEABLE FUSED BULBS are identified withwhite bases. There is one fuse bulb for each lighted circuit of 50 bulbs.Always replace burned-out bulbs promptly. If anumber of bulbs are burned out, extra stress is puton the remaining bulbs in the circuit. This may causeadditional bulbs to burn out prematurely. When afuse bulb fails the entire circuit will not light.• Risk of fire. This product employs overload protection (fuse bulb) in eachseries circuit to provide overload protection in addition to the fuse(s) located inthe plug. Do not replace the fuse bulb contained in this set with any othertype of bulb. Use only spare fuse bulbs provided with this product.Note: G35 LED’s are non-replaceable. Tampering with this set voidsthe warranty.Replace Steady Bulb: Before changing bulbs, make sure set is unplugged.NOTE: Steady and Fuse bulbs are not interchangeable.a) Grasp plug andremove from thereceptacle or otheroutlet device. Do notunplug by pulling cord.b) Hold bulb by the plasticbase and pullbulb/base straight out of socket.c) Replace bulb with only 2.5 Volt,0.75Watt super bright midgetpush-in type lamp providedwith product.d) Push spare bulb/baseassembly into socket. Do nottwist bulb when inserting intosocket. If bulbs are twisted, partof the set will not light.If the spare bulbs provided with the product have no plastic base orthe plastic base does not fit, first follow a)-b) above. Then 1) Removethe old bulb by straightening the bulb wires andpulling bulb straight from the base. (Fig. a), 2)Replace the new bulb by straightening the bulbleads and aiming each wire into a separate holein the plastic base (Fig. b), 3) Make sure eachbulb lead comes out an exit opening at the bottom of the plastic base.Now bend each lead up such that each bulb lead fits closely againstthe narrow side and in the center of the plastic base (Fig. c).Replace Fuse Bulb:NOTE: Fuse bulbs are secured in the base with adhesive. Do notattempt to remove.Remove old fuse bulb and replace with only 2.5 Volt, 0.75Watt fusebulbs provided with product.CAUTION:• To reduce the risk of fire and electric shock:a) Do not install on trees having needles, leaves or branch coverings of metalor materials which look like metal, andb) Do not mount or support strings in a manner that can cut or damage wireinsulation.• To reduce the risk of overheating, replace burned-out lamps promptly. Use2.5 Volt, 0.75Watt lamps only.• This Pre-Lit tree is rated 339 Watts, do not overload.For Indoor Use Only Printed in ChinaREPLACEABLEFUSED BULBS:identified with awhite base.

/ 2

Related manuals for GE 00684