GE 23501a Manual

Also see for 23501a: Manual

MODELO NO. 23501aFOR INDOOR AND OUTDOOR USEIMPORTANT SAFETY INSTRUCTIONSWhen using electric products, basic precautions should always be followed including the following:a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. Whenproducts are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.c) This seasonal use product is not intended for permanent installation or use.d) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.f) Do not let lamps rest on the supply cord or on any wire.g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.h) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock itshould not be played with or placed where small children can reach it.i) Do not use this product for other than its intended use.j) Do not hang ornaments or other objects from cord, wire, or light string.k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.l) Do not cover the product with cloth, paper or any material not part of the product when in use.m)This product is equipped with push-in type lamps. Do not twist lamps.n) Read and follow all instructions that are on the product or provided with the product.o) SAVE THESE INSTRUCTIONSUSE AND CARE INSTRUCTIONSa) When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place onlive trees in which the needles are brown or break off easily. Keep the tree holder filled with water.b) If the product is placed on a tree, the tree should be well secured and stable.c) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, orfrayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, orexposed copper wire.d) When storing the product, carefully remove the product from wherever it is placed, including tree, branches,or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.e) When not in use, store neatly in a cool, dry location protected from sunlight.USER SERVICING INSTRUCTIONSReplace the lamp.1. Grasp plug and remove from the receptacle or other outlet device.Do not unplug by pulling cord.2. Pull lamp and plastic base straight out of lampholder.3. Replace lamp with only 3.3 Volt, 0.066 Watt,LED type lamp (provided with product).If the new lamp base does not fit in lampholder, follow the steps below step 3.a) Remove the base of burned out lamp by straightening lamp leads and gently pull lamp out.b) Thread leads of new lamp through holes in old base with one lead in each hole.c) After lamp is fully inserted into base, bend each lead up, like other lamps in thelight set so that the leads will touch the contacts inside the lampholder.CAUTION:1. Replace lamps only with 3.3 volt, 0.066 watt spare lamps provided with this product.2. Risk of fire. This product does not contain lamp shunts, which allow the product to operate if one lampburns out. Do not replace lamps with other than the spare lamps provided with this product.Warning: Changes or modifications to this unit not expressly approved by the partyresponsible for compliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates, usesand can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.For questions and /or assistance, call customer service at 1-877-398-7337or visit us on the web at www.geholidaylighting.com FP-18 PRINTED IN CHINA©2018 Nicolas Holiday Inc., 204 Spring Hill Road Trumbull, CT 066119F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560 All rights reserved.TROUBLESHOOTINGPROBLEM POSSIBLE CAUSE CORRECTIVE ACTIONIf the productdoes not light One or more of the based LEDs mayhave loosened from the socket duringtransporting. There is a break in thecircuit between the LED leads and thesocket terminals. Male/femaleconnectors not fully inserted together.Non working control box. Foot pedalin off position.Unplug the set at the outlet. Starting with thefirst unlit LED, gently push (don't twist) eachLED base firmly into the socket. If still does notlight, then remove each based LED and checkfor out of place lead wires. Make certainconnectors fully inserted and securing cap fullytightened. Step on foot pedal to turn LEDs on.If a based LEDis missing One or more of the based bulbs mayhave come out of the socket whentransporting.Mark socket(s) with a piece of tape and unplugthe set. Replace the based LED or use one ofthe spare based LEDs included with product.If an LED fails tolight (shorts oropens)Incorrect LED, premature LED failureor voltage is too high. The LED may be out or dimly lit. Replace badLEDs as soon as you find them.LEDs fail toswitch fromwhite to multiIf applicable, then a defective controlbox or color change foot pedal. Contact Customer Support.

/ 2

Related manuals for GE 23501a