Menu
GE 19299 Installation Instructions Manual
Also see for 19298: Installation instructionsUser manual
  |
192981929919300Version 063/28/2016work, see TROUBLESHOOTING.3. Hold the back plate of the push buttonin the selected location with the arrowon the back of the back plate pointingup.4. Using the 1/16" drill bit, drill a holethrough the back plate of the pushbutton (See Figure 4 — Mounting holelocations) and into the surface of theselected location.5. Secure with the two screws provided.6. Press front housing onto back cover.7. Test operation. If chime does not work,see TROUBLESHOOTING.Temporary Push button (transmitter) mounting instructions1. Clean the mounting location for the push button with a mixture of 50% water and 50%isopropyl alcohol.2. Remove protective backing from one side of the adhesive pad and attach it to the backplate of the push button.3. Remove protective backing from the other side of the adhesive pad and press the backplate to the cleaned mounting location and hold in place for a few seconds to allow for asecure bond.Chime (receiver) mounting instructionsPlug the chime into the top receptacle of the outlet (See Figure 5).Extra chime receivers and push buttons available at www.byjasco.com.TroubleshootingIf the chime does not work:1. Make sure push button switch is pressed down and held for at least 1 second.2. Verify battery installation is correct, noting polarity.3. Try a fresh battery in push button.4. Make sure chime is no further than 150 feet away from push button.5. Ensure push button is not mounted on metal, near metal studs, or near the floor.6. Try a new location for the chime.7. If the chime and push button(s) do not operate, repeat the electronic pairing process ofthe push button(s) to the chime in steps A-F below.A. To clear settings: Press and hold the pairing buttonon the bottom of the chime while plugging the chimeinto the outlet.B. Once chime is plugged in, release the Pairing button.C. Press and hold the Pairing button again. You will hearthe “Ding Dong” melody twice, and then the doublebeep to alert you the chime is ready to pair with thepush button. Release the pairing button.D. Press and release the push button (See Figure 3). Youwill hear one beep letting you know the chime accepted the signal.E. Wait 10 seconds and you will hear the double beep again to alert you the chime is nowpaired with the push button.F. Press the push button to test.Functional range may be adversely affected by one or more of the following factors:weather, radio frequency interference, low transmitter battery, and obstructions betweenthe transmitter and receiver.This device complies with part 15 of the FCC rules. Operation is subject to the followingtwo conditions:(1) this device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation.FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused byunauthorized modifications to this equipment. Such modifications could void the user’sauthority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the useris encourage to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.• Consult the dealer or an experienced radio/TV technician for help.MADE IN CHINAGE is a trademark of General Electric Company and is under license by JascoProducts Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.This Jasco product comes with a 1-year warranty. Visitwww.byjasco.com for warranty details.Questions? Contact us at 1-800-654-8483 between 7:30AM—5:00PM CST.Wireless Door ChimeInstallation instructionsRequired tools: Small flat blade screwdriver, #2 Phillips screwdriver, and 1/16" drill bit(not included)The wireless door chime kit has two components:Installing battery in push button (transmitter)1. Remove the front cover of the push button housing by pushing a flat blade screwdriverinto the slot at the bottom of the push button housing (See Figure 1).2. Install the CR2032 battery (included) with the positive(+) side up.3. Keep the front cover off the push button until melody selection is complete.NOTE: the chime and push button(s) have been electronically paired during production.Once the battery is installed in the push button and chime is plugged in, press the pushbutton(s) to ensure that the push button(s) cause the chime to operate.IF CHIME DOES NOT SOUND, SEE TROUBLESHOOTING.Melody Selection Setting (your chime will have either 2 or 8 melodies)Select the melody by pushing the Melody selection button located inside the push buttonhousing (See Figure 1). Press and release the melody selection button until you hear thedesired melody. Table 1 and Table 2 shows the order the melodies will be heard.The last melody played will be your selected chime melody.Volume AdjustmentThere are four volume settings on this chime.1. To adjust the volume, press and release the pairing button on the chime to playthe melody.2. While melody is playing, press and release the volume button on the chimeto select the desired sound level.Push button (transmitter) mounting instructionsNOTE: Avoid mounting on metal surfaces, as it may result ina reduced range of transmission. Do not mount in an areaexposed to direct rain. Push buttons are typically mountedat the same height as the door knob or handle (between 36"and 44" above the floor).Permanent push button (transmitter)mounting instructions1. Remove the front cover of the push button(See Figure 1).2. Before mounting, choose a mounting location that is nofurther than 150 feet from the chime unit location. Placethe push button where you would like to mount and testwith the chime as close to its final location as possible. Ifit works, continue with mounting the button. If it does notChime (Receiver) Figure 2VolumePairingPushbuttonBattecompMeloselecbuttoPushbuttoPush flat blade screwdriver intothe slot to open the coverFigure 3Plug the chimeinto the topreceptacle ofthe outletFigure 5Table 2 - 8 Melody Chime1 Dingdong2 Westminster3 Knocks (3 times)4 Fanfare5 Mozart6 Good Vibes7 Patriotic8 TangoTable 1 - 2 Melody Chime1 Dingdong2 WestminsterPush Button (Transmitter) Figure 1PushbuttonMountingholelocationsBatterycompartmentMelodyselectionbuttonPushbuttonPush flat blade screwdriver intothe slot to open the coverMountingholelocationsBatterycompartmentMelodyselectionbuttonPushbuttonFigure 4 |
Related manuals for GE 19298
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved