Fujitsu PR-LN4 Setup Manual

Also see for PR-LN4: Software guide

KA02086-Y625-02EN© 2016 FUJITSU ISOTEC LIMITED This manual was made with recycled paper. Continued on the backPR-LN4 SETUP GUIDEStarting User Software1. Insert the attached CD-ROM into the CD drive of your computer running Windows. * If the [User Account Control] dialog box is displayed,2. The main menu starts automatically. click [Allow] or [Yes].Double click "PR-LN4 Installer" or select a "PR-LN4(LAN) Installer" and OK Button. * The Auto Play window will be displayed, click RunDLSELECT.EXE.- The explanation that follows assumes the following environment: * The displayed screens may vary with the environment- A DHCP server is included. in which you configure the PR-LN4.- A printer driver is already installed on your PC. * If the main menu does not start automatically,- In the case of Windows 8/Server 2012 and later, please start on a desktop screen. directly run DLSELECT.EXE on the CD-ROM drive- If you need to make detailed configuration settings or to change the existing (the D drive if the CD-ROM drive letter is D).configuration, refer to PR-LN4 Software Guide.Procedure for configuring the LAN cardGetting started CAUTION- Thank you for purchasing Fujitsu's printer LAN card PR-LN4. - INJURYInstalling this LAN card in your printer allows you to print in a network environment. Before starting installation, be sure to turn off- This setup guide explains the steps for configuring the PR-LN1 in a Windows environment. the power switch and disconnect the powerFor further information about the configuration method, refer to the online manual included plug from the outlet.in the CD-ROM supplied with this product. Otherwise, you may receive an electric shock.- Please note: When you install the LAN card, you will need to remove screws and the optioninterface cover. Keep these items on hand.- This setup guide applies only to computers running Windows.Components on the panel1. Network port(auto detects10BASE-T/100BASE-TX)2. Link/Act LED (Orange)3. Speed LED (Green)1. Network portConnects to the network cable.(Category 5 or higher for a 100BASE-TX network)2. Link/Act LED (Orange)Turns on when a link is established as 100BASE-TXor 10BASE-T. Blink when receiving a packet.3. Speed LED (Green)Turns on when the connection is detected as100BASE-TX.Turns off when not connected or when theconnection is detected as 10BASE-T.Checking the package contents and theitems that you will need to prepare- Before installing the LAN card, verify that the packagecontains the items below. If some item is faulty or missing,contact the store or dealer where you purchased this product. - Obtain the following.PR-LN4 Setup Guide (this Document)User Software CD-ROM(containing the configurationtools and manual)Installing the PR-LN4For DL7400Pro/DL7600Pro1. Turn off the power to the printer, disconnect the power cord,and remove the option interface cover from the printer.* Installing the LAN card in a printer that is turned on may cause aprinter failure.2. Verify that the LAN card can be inserted into the guides. Then installthe LAN card by inserting it into the guides and sliding it in until it stops.3. Confirm that the power to the printer is off, and then insert the power card.CAUTION1. If this product is to be connected to another printer, be sure to resetPR-LN4 setting tool to the factory default settings before starting theconnection work.2. Burn: Be sure not to touch the printer board during operation or after turning it off because apart of the printer board may be very hot. Touching the board under such circumstancesmay lead to injury or may even damage the board itself.Connecting to the network1. Verify that the power to the printer is off.2. Connect the network cable to the network port (10BASE-T or 100BASE-TX)on the PR-LN4.3. Connect the other end of the network cable to the Ethernet hub.4. Turn on the power to the printer and verify that the Link/Act LED on theLAN card goes on.PR-LN4 SETUP GUIDE143Ethernet hub2Install the PR-LN4in your printer.Install theLAN Setting Tool.Connect tothe network.Configure thePrinter port.5○ ×6 7Network cable** Use a Category 5 or higher network cableif you are using the PR-LN4 in a 100BASE-TXenvironment.1.2.3.

/ 2

Related manuals for Fujitsu PR-LN4