Fujitsu LPF-7200E User Manual

Also see for LPF-7200: Specifications

En-5EnglishFrançaisDeutschEspañol–– Be careful not to expose the projector to any steam, oily smoke, heat or humidity.Never place the projector in a location subject to steam, oily smoke heat or humidity. This may cause fire or electrical shock.–– Never place flammable objects such as a cigarette lighter, matches, gas canisters, spray cans, fireworks or plastic materials close to the lampventilation holes. This may cause fire or other damage.–– Always turn off the power switch before replacing the lamp. Allow the unit to cool off for at least one hour before replacing the lamp.Replace the lamp according to the directions in the operation manual. Fire, burns or electrical shock may occur if the replacement is performedincorrectly.–– A laser beam is projected if the laser button in the accessory wireless remote control is pressed. Never look directly into the laser beam.The laser beam may cause damage if it enters the eyes directly.–– As there is the possibility that ozone (O3 ) will be generated by the lamp power supply, handle the projector correctly according to the warningslisted in this operation manual.–– Be careful to avoid condensation.Dew or moisture condensation may be produced inside the projector if there are temperature differences between the inside and outside of theunit. Make sure that the projector has warmed up to room temperature before using it. This condition may cause electrical leakage, shock or fire.–– Be careful when transporting the projector.When transporting the projector, always remove the electrical plug and other cables. Be extremely careful to avoid dropping it or subjecting it toany shock or impact as this may cause fire or electrical shock.–– Never touch the electrical plug with wet hands.This may cause electrical shock.–– Do not touch the lamp storage cover interlock mechanism.Fire, electrical shock or other damage may occur if the interlock mechanism does not operate correctly.–– This product should be operated only with the type of power source indicated on the label. If you are not sure of the type of power supply to yourhome, consult your product dealer of local power company.–– Use a plug with a ground terminal. This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contactyour electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug.–– Use only the accessory cable designed for this product to prevent shock.The power supply voltage rating of this product is AC 100 – 240 V, the power cable attached conforms to the following power supply voltage.Use only the power cable designated by our dealer to ensure Safety and EMC.When it is used by other power supply voltage, power cable must be changed.The included cable differs according to the model.Using the Remote Control Laser PointerPOWERRGBMENUZOOM-PANZOOMMUTELASERVIDEOENTER/R-MOUSEVOLUMESOURCECANCELKEYSTONESTATUSFOCUSAUTOMOUSEPJAVOID EXPOSURE-LASERRADIATION IS EMITTED FROM THIS APERTURERAYONNEMENT LASERNE PAS REGARDER DANS LE FAISCEAUAPPAREIL A LASER DE CLASSE2EN60825-1 : 1994 + A11LONGUEUR D'ONDE : 650nmPUISSANCE MAXIMA : 1mWCAUTIONVISIBLE LASER RADIATIONDO NOT STARE INTO BEAMWAVE LENGTH : 650nm MAX OUTPUT : 1mWCLASS II LASER PRODUCTLASER RADIATIONDO NOT STARE INTO BEAMCLASS 2 LASER PRODUCTEN60825 - 1 : 1994 + A11WAVE LENGTH : 650nm MAX OUTPUT : 1mWLASER-STRAHLUNGNIGHT IN DEN STRAHLBLICKEN LASER KLASS 2EN60825-1 : 1994+A11WELLENLÄNGE : 650nmMAX AUSGANGSLEISTUNG : 1mWPlace ofManufacturer : AMade in JapanComplies with 21 CFR 1040.10 and 1040.11REMOTE CONTROL MODEL LPF-720RCMay-2000Laser window• When the LASER button on the remote control ispressed, a laser beam is emitted from the laserwindow shown in the figure.• Do not look directly at the laser beam and do notpoint the beam at another person.• Take care not to get the wireless remote controlunit wet. Failure may result.• Do not disassemble the wireless remote controlunit. Injury or failure may result.• Do not modify the wireless remote control unit.Injury or failure may result.CAUTIONUse of controls or adjustments or performance ofprocedures other than those specified herein mayresult in hazardous radiation exposure.Caution labelLASERbuttonPower cablePower supply voltage: AC100 –125V AC200 –240V AC240V