FAAC E024S Manual

Also see for E024S: User manual Manual

Contents

FAAC E024S Manual Manual pdf 10 page image

aa8 MEMORY STORING THE RADIO CODEThe control unit has an integrated 2-channel decoding system(DS, SLH, LC) named OMNIDEC. This system makes it possible tomemory-store both total opening (OPEN A) and partial openingOPEN B) of the automated system - this is made possible by anadditional receiver module (fig.3A ref. a) and Fig.3B ref. 1 forE024S for 391) and radio controls on the same frequency.The 3 types of radio codes (DS, LSH, RC) cannotcoexist.Only one radio code can be used at a time.8.1 MEMORY STORAGE OF DS RADIO CONTROLSA maximum of two codes can be stored. Oneon the OPEN A channel and one on the OPEN Bchannel.On the DS radio control, select the required ON-OFFcombination for the 12 dip-switches.Press the LOGIC (SW3) or SPEED (SW2) push-button, tomemory store respectively total opening (OPEN A) or partialopening (OPEN B), and as you hold it down, also press theSETUP (SW1) push-button. The relevant LED starts to flashslowly for 5 sec.Release both push-buttons.Within these 5 sec., press the appropriate push-button onthe radio control.The relevant LED lights up on steady beam for 1 second andthen goes OFF, indicating that storage was executed.To add other radio controls, set the same ON - OFFcombination used in point 1.8.2 MEMORY STORAGE OF SLH RADIO CONTROLSA maximum of 250 codes can be memorystored, split between OPEN A and OPEN B.On the SLH radio control, simultaneously press and holddown push-buttons P1 and P2.The radio control LED begins to flash.Release both push-buttons.Within 5 s, while the radio control LED is still flashing, press andhold down the selected push-button on the radio control(the radio control LED lights on with steady beam).Press the LOGIC (SW3) or SPEED (SW2) push-button torespectively memory store total opening (OPEN A) orpartial opening (OPEN B) and, by holding it down, press thepush-button SETUP (SW1The LED on the board lights up on steady beam for 1second and then goes OFF, indicating that storage wasexecuted.Release the radio control push-button.Quickly press twice the memory stored radio control push-button.1.2.3.4.5.6.1.2.3.4.5.6.7.8.7.2 MEMORY STORAGE OF BUS ACCESSORIESYou can add the BUS photocells to the system at any time,simply by memory-storing them on the board, observing thefollowing procedure:Install and program the accessories using the requiredaddress (see paragraph 7.1)Cut power to the board.Connect the two accessories cables to the red terminal-board J10 (any polarity will do).Power up the board, taking care to first connect the mainpower supply (transformer output) and then any batteriesand wait for the BUS LED to light on.Quickly press once only the SW1 (SETUP) push-button, toexecute learning. The BUS LED flashes.Give an OPEN impulse, leaves will move and the BUSlearning procedure is over.The board has memory stored the BUS accessories. Follow theinstructions in the table below to check if the BUS connectionis correct.Tab. 4 - Description of buS LEDSteady light Normal operation (LED ON even in theabsence of photocells)Slow flashinglamp (flashevery 0.5 sec)At least one input engaged: photocellengaged or not aligned, Open A or OpenB or Stop input engagedLight OFF(flash every 2.5sec)BUS line short circuitedFast flashinglamp (flashevery 0.2 sec)If you have detected a BUS connectionerror, repeat the acquisition procedure. Ifthe error is repeated, make sure that thereis no more than one accessory with thesame address in the system (also see theaccessories instructions)1.2.3.4.5.6.To change over from one code to another, you mustdelete the existing one (see paragraph on deletion),and repeat the memory-storage procedure.Fig. 3BFig. 3AE024S on 39E024S in boxENGLISH9