Epson UB-E04 User Manual

Also see for UB-E04: User manual Reference guide User manual User manual

EnglishIntroductionThe UB-E04 is an Ethernet interface board for Epson TM printers.This manual provides instructions, including a simple setup, to use this product safely and correctly.Key to SymbolsThe symbols in this manual are identified by their level of importance, as defined below. Read the following carefullybefore handling the product.CAUTION:Cautions must be observed to avoid minor injury to yourself, damage to your equipment, or loss of data.Note:Notes have important information and useful tips on the operation of your equipment.Features and FunctionsO Protocols: TCP, UDP, ICMP, IP, LP/LPR, TCP socket portO Communication standard: 10Base-T/100Base-TX, Full duplex/half duplexPart Names① Ethernet connector② USB Type-A connector③ Push button④ LED (green)⑤ LED (yellow)⑥ Password label** may not be attachedNote:Do not connect any equipment other than the Wireless LAN unit to the USB Type-A connector.Printer settingsIf the TM printer has a memory switch or a dip switch for “#25 pin reset signal” or “#31 pin reset signal” setting, do notchange the setting from Enable. Changing the setting may result in the printer to stop operating.Switch and function names may vary depending on the printer. For details, see the Technical Reference Guide of theprinter.CAUTION:Do not remove the interface board from or install the interface board into TM printer. Doing so may cause malfunctionof the printer or the interface board.Connecting the Cables1. Make sure both the printer and the host computer are turned off.2. Plug the Ethernet cable securely into the UB-E04’s Ethernet connector until you feel it click.CAUTION:Do not connect a telephone line, a display module cable, or a drawer kick cable to the Ethernet connector.Note:When the UB-E04 is installed, a customer display connector on the TM printer cannot be used.3. Connect the power supply cable to the printer.How to Set Up the ProductPreparationPrinting a Status SheetPower on the printer. Then, hold down the push button for more than 3 seconds to print a status sheet. You can checksetting values necessary (IP address, Subnet mask, Gateway address) for the network connection.ConnectionSet the setting of the host PC to match the network setting that you have confirmed with the status sheet.You can check whether the connection to the printer has been correctly done by inputting the ping command.Example: ping 192.168.192.168Note:Although the example shows the address 192.168.192.168, use whatever IP address is reported on the status sheet.Because the default IP addresses for all the printers are the same, you should power on and configure only one printer at atime.Resetting the product to Factory DefaultsHold down the push button on the interface card while turning on printer power and continue to hold it down until amessage that initialization starts is printed. This causes all internal settings to return to their factory defaults.SetupThere are two ways for the setup. For details, see the UB-E04 Technical Reference Guide.O Using a Web browser1. Input the IP address of this product in the address bar of the browser and press Enter.(Example: http://192.168.192.168 [default]).2. In the User authentication screen, enter the user name “epson” and the password.The initial password is as follows:Password label PasswordAttached Printed on the labelNot attached Printer’s serial number (10-digit alphanumeric characters, case-sensitive)Example of the password label:* The user name is fixed to “epson” but you may change the password.For security reasons, it is recommended to change the password from the default.3. Set parameters in each menu. If a parameter is changed, press [Send] to send settings to the printer.4. In the screen displayed after sending settings, press [Reset] to enable settings. When changing the IP address,etc., make sure settings in the host PC match that of the printer.O Using the EpsonNet Config (Ver. 4.5.7 or later)The EpsonNet Config is a utility to make network settings on an Epson printer with an Ethernet interface or awireless LAN interface.You can download the Technical Reference Guide and the EpsonNet Config from one of the following URLs.For customers in North America: https://www.epson.com/support/For customers in other countries and regions: https://www.epson-biz.com/Open Source Software LicenseThis product uses open source software in addition to Epson proprietary software.For information of the open source software used in this product, see the following URL.http://xxx.xxx.xxx.xxx/licenses.htmlFor “xxx.xxx.xxx.xxx” in the above URL, input your printer’s IP address.CautionCAUTION:Connecting an outdoor over head LAN cable directly to your product may lead to lightning damage. If you need toconnect such a cable to your product, the cable must be protected against an electrical surge between the cable andyour product. You should avoid connecting your product to a non-surge protected outdoor overhead LAN cable.CE MarkingU https://www.epson.eu/conformityFCC Compliance Statement for Users in the USAThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when theequipment is operated in a commercial environment.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordancewith the instruction manual, may cause harmful interference to radio communications. Operation of this equipmentin a residential area is likely to cause harmful interference in which case the user will be required to correct theinterference at his own expense.한국 사용자용이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서 가정용 환경에서 사용하는경우 전파간섭의 우려가 있습니다.WARNINGThis is a Class A product. In a domestic environment thisproduct may cause radio interference in which case theuser may be required to take adequate measures.The printers in which this board is installed becomesclass A devices.The connection of a non-shielded printer interface cableto this board will invalidate the EMC standards of thisdevice.You are cautioned that changes or modifications notexpressly approved by Seiko Epson Corporation couldvoid your authority to operate the equipment.The following standards are applied only to the interface boards that are so labeled. (EMC is tested using the Epsonpower supplies and TM series printers.)Les normes suivantes ne s’appliquent qu’aux cartes d’interface ainsi étiquetées. (CEM est testé à l’aide des blocsd’alimentation Epson et des imprimantes de la série TM.)Europe: CE markingNorth America/Amérique du Nord: FCC Class A, CAN ICES-3 (A)/NMB-3 (A)Oceania: Radiocommunications (Electromagnetic Compatibility) Standard , Class AAVERTISSEMENTCet appareil est un produit de classe A. Dans unenvironnement résidentiel, il risque de provoquer unbrouillage radio, auquel cas l’utilisateur pourra être tenude prendre des mesures adéquates.Les imprimantes dans lesquelles cette carte est installéedeviennent des appareils de classe A.La connexion d’un câble d’interface d’imprimante nonblindé à cette carte invalidera les normes CEM de cetappareil.Vous êtes averti que les changements ou modificationsnon expressément approuvés par Seiko EpsonCorporation peuvent invalider votre droit à fairefonctionner l’équipement.Standards and ApprovalsEnglish Français Español TürkçeRomână Українська 日本語https://support.epson.net/p_doc/938/User’s Manual / Manuel d’utilisation / ユーザーズマニュアルPrinted in XXXXXXImprimé XXXXXXImpresso XXXXXXImpreso en XXXXXX©Seiko Epson Corporation 2015–2023

/ 2

Related manuals for Epson UB-E04