Epson Pulsense PS-100 Quick Start Manual

Also see for Pulsense PS-100: Quick start guide

Contents

declaration of conformity

Pulsense ™ PS-100Quick StartRead these instructions before using your product.Charge your productBefore using your product for the first time, make sure thebattery is fully charged. Charging takes approximately 1.5 to2.5 hours. A full charge lasts about 36 hours.Caution: Do not attach the charging cradle when the PS-100 iswet. If the PS-100 is wet, wipe it with a damp cloth, remove themoisture with a towel, then let it air dry before attaching thecharging cradle.1. Center the PS-100 under the large tab, then press downuntil it clicks into place.2. Insert the USB plug into a power source. You can use:■ Computer (USB is for charging only, not for datatransfer)■ Optional USB AC Adapter (part number SFAC04)The orange LED lights up when your PS-100 is connectedcorrectly. Charging is complete when the blue LED is lit.To remove your PS-100 from the charging cradle, press thesmall tab down and push the PS-100 out from the back.Install Epson PULSENSEViewDownload Epson PULSENSE View from your mobiledevice’s app store.The following mobile devices are supported:■ iPhone 4s, iPhone 5, iPhone 5c, or iPhone 5s with iOS7.1 or later■ Mobile device running Android TM 4.3 or later withBluetooth ® SmartLaunch the app and pair yourPS-100You must pair your PS-100 through the Epson PULSENSEView app. The PS-100 will not store any data until you’vepaired it with the app.Follow these steps:1. Start the Epson PULSENSE View app.2. Make sure that the PS-100 is within 3 feet (1 meter) of themobile device.3. Follow the on-screen instructions to pair your PS-100with your mobile device and perform the initialconfiguration.The PS-100 can store up to 480 hours of data before needingto be synced.LED statusThe LEDs on the PS-100 light up or flash to indicate differentstates. When exercising, the LEDs indicate which zone you’recurrently in. The PS-100 vibrates when entering or leaving azone.Wearing your PS-100Follow these steps to adjust the wristband:1. Unfasten the buckle of the wristband.2. Unhook the band and adjust it to fit your wrist.Keep these tips in mind when wearing your PS-100:■ The Pulsense band needs to be worn snugly around thewrist to collect more accurate heart rate data. This maycause a slight impression on the wrist. Adjust the band forthe comfort and performance you choose.■ When wearing the PS-100, make sure it does not touchthe ulna bone.■ For greater accuracy, wear the Pulsense band on yournon-dominant wrist.■ Before boarding an aircraft, put your PS-100 in airplanemode by repeatedly tapping the top of the band.Calibrating your heart rateTo personalize your heart rate zones and calibrate the sleepmonitoring feature, wear your PS-100 for 2 to 7 days whileyou sleep. The accuracy of your heart rate zone and sleep datawill improve after the PS-100 has calibrated your resting heartrate.Using PULSENSE ViewYou can view live and collected data, such as hearcalories, and sleep, from your PS-100 using the PView mobile app.Troubleshooting■ The PS-100 vibrates when entering or leavingturn off vibration, go to > Device SettingVibration in the PULSENSE View app. See thelp for more information about vibration.■ If you are missing data, note that data collectepairing with the app cannot be viewed.■ If you are having trouble pairing, make sure ypairing from the PULSENSE View app, not fsystem’s Bluetooth settings.Where to get helpInternet supportVisit epson.com/support/ps100 (U.S.) orepson.ca/support/ps100 (Canada) for solutions tproblems. You can get tips, usage information, andownload utilities, view the User’s Guide, or e-mTelephone support servicesCall (562) 276-4394 (U.S.) or (905) 709-3839 (CSupport hours are 6 AM to 8 PM, Pacific Time, Mthrough Friday, and 7 AM to 4 PM , Pacific Time,Days and hours of support are subject to changenotice. Toll or long distance charges may apply.NoticesSafety instructionsWARNING:■ Exercise according to your physical capabilities■ Stop exercising and consult your doctor if youduring exercise.■ This product is not intended for use to diagnosetreat disease or other conditions, and is not a mdevice.■ If you have any concerns, consult your doctorthis product.■ To avoid the possibility of skin irritation or discowearing the PS-100, you must keep the skin unclean and dry at all times. Do not allow water, sskin, or dirt to build up under the band. It is impkeep the band clean and dry at all times by wipwith a damp cloth, removing the moisture withletting it air dry.■ Stop using the PS-100 immediately if you havereaction to the band. Please consult your doctodevelop a rash or skin irritation.■ Remove the band from the wrist when rechargbattery.■ Do not use or store this product in the followingenvironments: locations with very high or low teor humidity, near volatile substances, dusty plastrong magnetic fields (for example, near a louDoing so may cause electric shock, fire, or themalfunction or be damaged.■ Do not disassemble this product, and do not atrepair it by yourself. It may cause an electric shaccident.■ Do not leave this product within reach of youngCaution:■ Although the PS-100 is water-resistant, do notdirectly onto this product or submerge it in watecompromise the water-resistant feature and caproduct to fail.Blue OrangeApp icon MeaningNo network connection. Make sure you have anetwork or data connection, then tap the icon toreconnect.No Bluetooth connection. Make sure Bluetooth isenabled on your product and mobile device, then tapthe icon to reconnect.Light pattern StatusHeart rate is below the fat burningzoneHeart rate is approaching the fatburning zoneHeart rate is in the fat burning zoneHeart rate is in the aerobic exercisezoneHeart rate is in the anaerobicexercise zoneHeart rate is above the anaerobicexercise zone (flashing rapidly)The battery is lowAirplane modeUlna boneSettings Swipe down for liveheart rateRefreshSSroSdE

/ 4

Related manuals for Epson Pulsense PS-100