Electrolux EW26SS70IS4 Installation Instructions Manual

B]Tools Necessary:Installation Instructions for Side-By-Side Refrigerator This document should only be removed by customer after installation.1 Pro are The installationSiteYour refrigerator is designed to be part of a built-in kitchencabinet system. Besure to coordinate site preparation andinstallation with your kitchen contractor.Includethese minimum guidelinesin your site preparation:* Choosea place near a grounded electrical outlet.Do not use an extension cord or an adapter plug.Avoid direct sunlight and close proximity to a range,dishwasher or other heat source.Floorshould be leveland able to support a fully loadedrefrigerator.The refrigerator's Ice & Water Dispenser requires watersupply access.. Planfor easyaccessto countertops when removingfood.Forcomplete access to drawers and freezer baskets,doors must be able to fully open.Allow the following clearancesfor ease of installation, proper air circulation, and plumbing and electricalconnections: Sides & Top:3/8 inch Rear. 1 inchTrans ort Un acka ed Refri orator To SiteBy now, you have already removedyour refrigerator's shipping carton.You rnaystill needto use a hand truck to move it through closespaces or entrances. If the refrigerator islargerthan an entrance, consider two options:Removethe entrance door if one exists.Removethe refrigeratordoors (see how in your Use& Care Guide).When using a hand truck:* Load refrigerator from side of cabinet only.Do not run retaining straps over handles.Do not over-tighten retaining straps.Neveruse refrigeratorhandlesto move the refrigerator.* Removetape from doors only after unit is in place.ConnectWater Su !Before Installing The Water Supply Line, You Will Need:* Basic Tools: adjustable wrench, flat-blade screwdriver,and Phillips TMscrewdriverAccess to a household cold water line with waterpressure between 30 and 100 psi.A water supply line made of 1ginch (6.4ram) OD, copperor stainless steel tubing. To determine the length oftubing needed,measure the distance from the ice makerinlet valve at the back ofthe refrigerator to yourcold water pipe. Then addapproximately 7 feet (2.1meters), so the refrigeratorcan be moved out forcleaning (as shown).A shutoff valve to connectthe water supply line to yourhousehold water system. DONOTuse a self-piercing typeshutoff valve.A compression nutand ferrule (sleeve) forconnecting a copper watersupply line to the ice makerinlet valve.To Connect Water Supply Line To Ice MakerInlet Valve1. Disconnect refrigerator from electric powerSOUrCe,2. Place end of water supply line into sink orbucket. Turn ON water supply and flush sup-ply line until water is clear. Turn OFFwatersupply at shutoff valve.3. Remove plastic cap from water valve inlet anddiscard cap.4. If you use copper tubing - Slide brasscompression nut, then ferrule (sleeve) ontowater supply line. Push water supply lineinto water valve inlet as far as it will go\I Z_at_ Vak,et (it;elude erlough _ubir;9 it; _op m alk_w(1Ainch/6.4 mm). Slide ferrule (sleeve) into alve inlet and finger tighten compression nut ontovalve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 1.If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slidecompression nut onto valve inlet and finger ghtencompression nut onto valve. Tighten anotherhalf turn with a wrench; DO NOT over tighten. See Figure 2.With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator5.as shown.6. Coil excess water supply line (copper tubingand arrange coils so they do not vibrate or7. Turn ON water supply at shutoff valve and8. Reconnect refrigerator to electrical power9. To turn ice maker on, lower wire signal arm (switch to the "l" position (rear mounted)._nly), about 2½ turns, behind refrigerator as shown_ar against any other surface.hten any connections that leak.Jrce._ide mounted) or set the ice maker's 0n/0ff poweriiii_iiiii_i_!i!_ii_i_i!iiii_ili!_!!iii_i_i!iii!_ili_I_I_ii!i!ii!i!_i;iiii_iiiii_iiiii_iiiiiiiii!iiiii_!iiii!!i;!!i_i_i_i_i_i_i_ii_i;!_iiiiii_i!ii!i_i_!iiiii!i!iiii_iii_i!!i,iii!i_iii!_i:i_i!iiiiii!;ii_!ili;iiii!_!ii!i!_!_i;i!i_i_i_:_:!_!_i!_i_i!_i_i_:i_i_!i_i_!_i_i_i_!_!;!_ii_i_!i_i_!_;_i!i!_:!_!i!_!i_;iii_!i_;_!i_;_!i_;i!_i_!_!!!i_!!;!_:_!_i_!_!JJii_!i!i_!i_i_!_!!i_i!i_!i_!_i_ii!_!!_!i_i;i_!!ii_i_i_i:!ii!iii_i!i!_i:ii!_i_i!ii_i!iii_i!i_i!iiii_ill_i_iiii_i:i!i_!,!i!_!,!i_!_i_i_!i!iiPlaceIn Permanent tuitionLevelRefrigerator & Adjust Doors(if necessary)'½.,oo,o,,oo_%,_o,,,,o-_To install toe grille !io.o"_._,_ _1 Open both doors. Slide left and right es of toe grille overlower hinges of refrigerator.2 While pushing toe grdle firmly against binet, fasten bottomclips of toe grille to cabinet.3 Fasten top clips to cabinet.4 Close the doors. Fasten right and left side clips into groove of bottom hinge.To remove toe grille1 With both doors closed, unfasten right and left side clips of toegrille from bottom hinge grove.2 Open both doors. Press firmly on top of toe grille until top of toegrille pops off.3 Pull toe grille outward towards your bod_ .nd off of lower hinges.NOTE: Level the unit with the adjustable rollers _fore leveling the doors.To level the doors using the adjustable lower hinge (some models): _i1 Before leveling either door, remove set screw that locks door height into posi- _1I_li °_'_T Ttion. (The door cannot be adjusted without set screw removed.) _ EtCh/2 If the refrigerator door is lower than the freezer door, raise the refrigeratordoor by turning the adjustment screw counterclockwise using a 7/l_inchwrench. (See iflustration.)3 If the freezer door is lower than the refrigerator door raise thefreezer door byturningthe adjustment screw counterclockwise _1 .....................using a 7/_ inch wrench. (See dlustration.) ....._!_,!:_!!_!_i........................,_*::;::::........................................4 After leveling, verify door stop contacts lower hinge and top of door i:_;does not contact upper hinge through full movement of door (from % ifully closed to fully open). '_'i5 Replace the toe grdle by fitting it into _ ce.RemoveInternal Shi in MaterialsElectrolux uses packing foam and tape to secure the internal parts of your refrigerator for shipping. Oncethe refrigerator is in position, you can remove this material.1 PIECE OF TAPE--3 PIECES OF TAPE--3 PIECES OF TAPE--2 PIECES OF TAPE_5 PIECES OF TAPE--2 PIECES OF TAPE_4 HECES OF TAPE--2 PIECES OF TAPE _1 FOAM BLOCK-...................._SHELF SPACER WiTH TOE GRILL_ i l-- 4P_ECESOFTAPE4 PIECES OF TAPE_ I BOX OF DOOR BINSAND DAIRY COMPARTMENT_--_4 P,ECESOFTAPEi _ . ,---"'t _ 1 BOX OF DOOR HANDLESX J _ AND 2 PIECES OF TAPE_--_P,ECESOFTAPEC_--_ 7 PIECES OF TAPEFOAMOLOCKSLocation of these materials may vary depending on your model,7 Problems?TryThese SuggestionsOperation problems are possible if any of the installation tasks are not completed. Here is a list of things tocheck for:Is the refrigerator's power cord plugged in?Is the refrigerator connected to the household water supply?If you had to remove the refrigerator and freezer doors, did you reattachwater and power connectorsat the door hinges? (Seethe Use& Care Guide for detailed instructions on removing and replacingdoors.)Is the ice maker power switch turned On?Other possibilities to check:Is the power to the receptacleturned on?Is the water filter above the fresh food compartment fully seated (see Use& Care Guide for details)?If you still have operation problems after checking these suggestions, please see the "Solutions ToCommon Problems" section in your Use & Care Guide., ?What s Next.Congratulations. You are ready to begin enjoying your new Electrolux refrigerator.* To become aware of important safety instructions and learn how to operate your refrigerator, pleaseread the entire Use & Care Guide.* You may want to start with the "Normal Operating Sights & Sounds" section of the Guide to learnmore about what to expect during typical operation.Pleaseregister your product. You can register online at www.electroluxusa.com, or you can simplysend in the Registration Card.Andthankyou for choosingElectro/ux.9 I--4In II i n h k ff LiDoors ice MakerE]Handlesare secure and tightE]Door seals completely to cabinet on all sidesE]Freezerdoor is level across the topLevelingE]Refrigerator is level,side to side and tiltedW' (6ram) front to backE]Toegrille is properly attached to refrigeratorDCabinet is setting solid on all cornersElectrical PowerE]House power turned onE]Refrigerator plugged inE]House water supply connected torefrigeratorE]No water leaks present at all connections -recheck in 24 hoursE]lce Maker is turned ONE]lce & Water Dispenser operates correctlyE]Front filter must be flush with filter housing(some models)Final ChecksE]Shipping material removedE]Fresh Food and Freezer temperatures setE]Crisper Humidity controls setE]Registration Card sent inNot satisfied with the installation of your refrigerator? L> Please contact the store you purchased it from.

/ 1

Related manuals for Electrolux EI23CS55GB6